SBX218
2 x 18" Powered Subwoofer
► Powerful neodymium transducers
with tremendous motor strength
reduce system weight and increase
output response at all output levels.
► 4-in Voice Coil Drivers
► Cable Chases for Concealed Wiring
and Rigging.
► Multiple tie down points for secure
stacking.
► Universal power supply for reliable
operation on any mains source
anywhere in the world
OVERVIEW
The SBX218 is a high output subwoofer
system designed to support any system from
RSX to ADAPTive Series products. SBX Series
use of neodymium woofers with a 4-in voice
coil ensures the best sonic performance,
meeting expectations for medium to large
venues.
Tie Down Points
Do not hang or y
from these points
Runner
Pole Cup
Cable Pass Thru
Conceal wiring for
clean look
Engineered for both production and
installation uses, SBX218 is equipped with a
threaded pole mount and rugged handles,
making for a perfect solution for small gigs
to large concert systems. Integrated runners
on the top and sides lock subs together
to resist movement due to vibration and
provide a clean look. Support of ground stack
operation of NTX can be accomplished with
two sets of ybar locating pins, providing safe
operation at any splay angle
SBX218's hefty grill with large openings
protects the woofers, resists damage, and
is acoustically transparent. The ultra large
port, inspired by aircraft design, eliminates
port noise. EAW DynO™ gets every last dB of
performance out of the system in the most
challenging conditions.
Handles
Front Panel LED
One Main Street | Whitinsville, MA 01588 | Tel 800 992 5013 / 508 234 6158 | www.eaw.com
EAW products are continually improved. All specications are therefore subject to change without notice. ©2021 Eastern Acoustics Works
SBX218 Module
TECHNICAL SPECIFICATIONS
DUAL 18" POWERED SUBWOOFER
PERFORMANCE
Max SPL (Half Space) 141dB
Operating Range 25Hz–120Hz
ELECTRICAL
Input Type Electronically Balanced
Max Input Level 21dBu
Impedance 20 kOhm (balanced)
Input Wiring
Input Selection Analog, Dante
Ampliers & Processing
(LF/HF) Type
Maximum Output 2 x 2500W
Driver Protection Integral DSP limiting
AC Mains (nominal)
Connector
Input 100 V TO 240 V
Frequency 50 Hz to 60 Hz
Power Consumption Idle – 40W
Controls/Communication
Connections
Protocols Ethernet/Dante
Software EAW Resolution 2™
XLRF, Pin 1 chassis, pin 2 +, pin 3 – separate
loop-thru XLRM (for analog signal only)
Modied Class D
Neutrik PowerCON TRUE1 TOP
1/8th - 400W
1/3rd - 600W
Full - 1100W
Neutrik PowerCON TRUE1 TOP
CONFIGURATION
Subsystem
Operating Mode
Single Amp
ORDERING DATA
Part Numbers:
SBX218 Black 2070846-70
Accessories
SBX218|CART 207107870
SBX218|CASTER KIT 2070738
SBX218|COVER 2071298
NTX|RAINSHIELDHORIZONTAL 2070971
M20 THREADED POLE 2047634
PHYSICAL
Dimensions (H × W × D) 21.3 X 52.7 X 31.5in (540 X 1340 X 800mm)
Weight 208 lbs.
Transducer Loading
2x18" cone, 4" VC Vented
Amplier Channels External Signal Processing
VLF DSP w/EAW DynO™
PERFORMANCE GRAPHS
Frequency Response1 =60Hz Seting =100Hz Setting
1 Variation in acoustic output level with frequency for a constant input signal. Processed: normalized to 0 dB SPL. Unprocessed inputs: 2 V (4
ohm nominal impedance), 2.83 V (8ohm nominal impedance), or 4 V (16 ohm nominal impedance) referenced to a distance of 1 m.
2
Tel 800 992 5013 / +1 508 234 6158 | www.eaw.com
SBX218 Module
3
Tel 800 992 5013 / +1 508 234 6158 | www.eaw.com
SBX218 Module
SIGNAL DIAGRAM
INPUT PANEL
1 XLR Input
2 XLR Thru
3 Dante A / B
4 LCD UI Display
5 DSP Navigation / Edit Wheel
One Main Street
Whitinsville, MA 01588
4
Tel 800 992 5013 / +1 508 234 6158
www.eaw.com
1903_SB818P|F_SPEC
Loading...