Page 1
NSX-T99
EZ
SERVICE MANUAL
COMPACT DISC STEREO
CASSETTE RECEIVER
SYSTEM
NSX-T99 CX-NT99
• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
NSX-T99, (S/M Code No. 09-003-426-5T2).
• If requiring information about the CD mechanisim, see Service Manual of 6ZG-1,
(S/M Code No. 09-001-338-7N2)
CASSEIVER
BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM
BASIC CD MECHANISM : 6ZG-1 ZRNDM
CD
SPEAKERS
SX-WNT99 RC-ZAS04
REMOTE
CONTROL
S/M Code No. 09-005-426-5R2
REVISION
DATA
Page 2
SPECIFICATIONS
<FM Tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity(IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<MW Tuner section>
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
Usable sensitivity 350 uV/m
Antenna Loop antenna
<LW Tuner section>
Tuning range 144 kHz to 290 kHz
Usable sensitivity 1400 uV/m
Antenna Loop antenna
<Amplifier section>
Mid-high frequency amplifier
Power output* Rated: 45 W + 45 W
(8 ohms, THD 1 %,1 kHz / DIN 45500)
Reference: 55 W + 55 W
(8 ohms, THD 10 %,1 kHz / DIN 45324)
DIN MUSIC POWER: 100 W + 100 W
Total harmonic distortion 0.3 % (28 W, 1 kHz, 8 ohms,
DIN AUDIO)
Low frequency amplifier
Power output* Rated: 135 W + 135 W
(6 ohms, THD 1 %, 75 Hz / DIN 45500)
Reference: 165 W + 165 W
(6 ohms, THD 10 %, 75 Hz / DIN 45324)
DIN MUSIC POWER: 310 W + 310 W
Total harmonic distortion 0.3 % (84 W, 75 Hz, 6 ohms,
DIN AUDIO)
* without connecting to surround speakers
Inputs VIDEO/AUX : 300 mV (adjustable)
MD : 300 mV (adjustable)
MIC1,MIC2 : 1.0 mV (10 kohms)
LINE OUT : 150 mV
Outputs SPEAKERS HIGH FREQ :
accept speakers of 8 ohms or more
SPEAKERS LOW FREQ :
accept speakers of 6 ohms or more
SURROUND SPEAKERS : accept
speakers of 8 to 16 ohms
PHONES (stereo jack) : accepts
headphones of 32 ohms or more
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response CrO2 tape: 50 Hz – 16000 Hz
Normal tape: 50 Hz – 15000 Hz
Signal to noise ratio 60dB (Dolby B NR ON, CrO2 tape
peak level)
Recording system AC bias
Heads Deck 1: Playback head x 1
Deck 2: Recording/Playback head
x 1, erase head x 1
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 83 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
Wow and flutter Unmeasurable
<Speaker system SX–WNT99>
Cabinet type 4 way, built-in subwoofer
Speakers Subwoofer :
200 mm ( 77/8 in.) cone type
Mid range:
100 mm (4 in.) cone type
Tweeter :
60 mm ( 23/8 in.) cone type
Super Tweeter :
20 mm (13/16 in.) ceramic type
Impedance 6 ohms / 8 ohms
Output sound pressure level 87 dB/W/m
Dimensions (W x H x D) 260 x 463 x 314 mm
(101/4 x 181/4 x 123/8 in..)
Weight 8.0 kg (17 lbs 10 oz)
<General>
Power requirements 230 V AC, 50Hz
Power consumption 255W
Dimensions of main unit 300 x 382.6 x 396.4mm
(117/8 x 151/8 x 15 5/8in.)
Weight of main unit 13.2 kg (29 lbs 2 oz)
Standby power consumption
If the power-economizing mode is OFF: 37 W
If the power-economizing mode is ON: 0.9 W
• Design and specifications are subject to change without
notice.
• Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
• The word "BBE"and the "BBE symbol" are trademarks of BBE
Sound, Inc.
Under license from BBE Sound,Inc.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy P.C.B
Solder
– 3 –
Page 4
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
FRONT C.B
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
15
C113
Short with tweezers.
Fig-2-2
C113
%
*
VSS
VDD
MICROCOMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
Page 6
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
8A-NF3-635-010 C-IC,LC876596W-5P49
87-A21-482-010 IC,RPM6938-H4
87-A20-869-040 C-IC,M62449FP
87-A21-398-010 IC,STK490-110
87-A20-355-010 IC,CXA1553P
87-A20-783-040 C-IC,BA7762AFS
87-A21-577-040 C-IC,M61506FP
87-070-289-040 IC,BU 2092F
87-A21-021-040 C-IC,BU2099FV
87-A21-018-040 C-IC,M65849BFP631D
87-A21-452-030 C-IC,BD3876KS2
87-A20-440-040 C-IC,BU1920FS
87-A21-560-010 IC,LA1844L-A
87-070-127-110 IC,LC72131 D
87-020-454-010 IC,DN 6851
TRANSISTOR
87-026-245-080 TR,DTC114ES
87-A30-217-010 TR,2SB1436(R)
87-A30-198-080 TR,KTC3199GR
89-213-702-010 TR,2SB1370E
87-A30-218-080 TR,2SB1237(Q)
87-A30-087-080 C-FET,2SK2158
87-A30-086-040 C-TR,CSD1306E
87-A30-076-080 C-TR,2SC3052F
87-A30-107-070 C-TR,CMBT5401
87-A30-074-080 C-TR,RT1P 141C
87-A30-190-080 TR,CC5551
87-A30-105-080 C-TR,RT1P441C
87-026-610-080 TR,KTC3198GR
87-A30-106-040 C-TR,CMBT5551
87-A30-276-040 C-TR,DTA143EKA
87-A30-063-080 C-TR,KRA104S
87-026-609-080 TR,KTA1266GR
87-A30-186-010 FET,2SK3053
87-A30-075-080 C-TR,2SA1235F
87-A30-329-080 TR,CD1585BC
87-A30-318-080 TR,CSA952K
89-327-143-080 TR,2SC2714O
87-A30-072-080 C-TR,RT1P 144C
87-A30-234-080 TR,CSC4115BC
89-503-602-080 C-FET,2SK360E
87-A30-269-040 C-FET,2SJ461-T1
87-A30-097-010 TR,FN1016
87-A30-098-010 TR,FP1016
87-A30-073-080 C-TR,RT1N141C
87-026-463-080 TR,2SA933S
DIODE
87-A40-673-090 DIODE,D10XB20
87-020-465-080 DIODE,1SS133
87-A40-438-080 ZENER,MTZJ4.7A
87-017-654-060 DIODE,GBU6JL6131
87-A40-736-080 DIODE,1N4148M(SEM)
87-A40-553-080 DIODE,1N4003 LES
87-A40-781-080 ZENER,UZ36BSA
87-070-274-080 DIODE,1N4003 SEM
87-A40-768-080 ZENER,UZ16BSA
87-017-154-080 ZENER,HZS6C3L
87-A40-488-080 DIODE,1SS244
87-020-331-080 CHIP-DIODE,DAN202K
87-A40-313-080 C-DIODE,MC 2840
87-A40-270-080 C-DIODE,MC2838
87-A40-751-080 ZENER,UZ6.2BSB
87-A40-269-080 C-DIODE,MC2836
87-A40-747-080 ZENER,UZ5.1BSB
87-A40-646-010 DIODE,FMB-G16L
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
87-A40-764-080 ZENER,UZ10BSC
87-017-149-080 ZENER,HZS6A2L
MAIN C.B
C3 87-A10-712-080 C-CAP,S 0.22-50 F
C4 87-A10-712-080 C-CAP,S 0.22-50 F
C21 87-016-035-090 CAP, E 6800-35 VR
C22 87-016-035-090 CAP, E 6800-35 VR
C25 87-010-990-080 CAP,E 33-100 SME
C26 87-016-300-080 CAP,E 22-100 SME
C27 87-010-990-080 CAP,E 33-100 SME
C28 87-016-300-080 CAP,E 22-100 SME
C31 87-010-263-080 CAP, ELECT 100-10V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-247-080 CAP, ELECT 100-50V
C35 87-010-406-080 CAP, ELECT 22-50V
C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-393-080 CAP, ELECT 100-35V
C39 87-010-393-080 CAP, ELECT 100-35V
C40 87-010-190-080 S CHIP F 0.01
C60 87-010-403-080 CAP, ELECT 3.3-50V
C80 87-010-401-080 CAP, ELECT 1-50V
C81 87-010-374-080 CAP, ELECT 47-10V
C82 87-010-260-080 CAP, ELECT 47-25V
C104 87-010-196-080 CHIP CAPACITOR,0.1-25
C105 87-010-196-080 CHIP CAPACITOR,0.1-25
C111 87-010-401-080 CAP, ELECT 1-50V
C112 87-010-401-080 CAP, ELECT 1-50V
C115 87-010-401-080 CAP, ELECT 1-50V
C116 87-010-401-080 CAP, ELECT 1-50V
C121 87-010-406-080 CAP, ELECT 22-50
C122 87-010-406-080 CAP, ELECT 22-50
C151 87-010-405-080 CAP, ELECT 10-50V
C161 87-010-184-080 C-CAP,S 3300P-50 K B
C162 87-010-184-080 C-CAP,S 3300P-50 K B
C163 87-010-196-080 CHIP CAPACITOR,0.1-25
C171 87-012-368-080 C-CAP,S 0.1-50 F
C172 87-012-368-080 C-CAP,S 0.1-50 F
C173 87-012-368-080 C-CAP,S 0.1-50 F
C174 87-012-368-080 C-CAP,S 0.1-50 F
C175 87-A11-572-080 C-CAP,S 0.015-50 K B
C176 87-A11-572-080 C-CAP,S 0.015-50 K B
C177 87-010-197-080 CAP, CHIP 0.01 DM
C178 87-010-197-080 CAP, CHIP 0.01 DM
C301 87-010-318-080 C-CAP,S 47P-50 CH
C302 87-010-318-080 C-CAP,S 47P-50 CH
C303 87-012-157-080 C-CAP,S 330P-50 CH
C304 87-012-157-080 C-CAP,S 330P-50 CH
C305 87-012-157-080 C-CAP,S 330P-50 CH
C306 87-012-157-080 C-CAP,S 330P-50 CH
C307 87-010-196-080 CHIP CAPACITOR,0.1-25
C311 87-010-198-080 CAP, CHIP 0.022
C312 87-010-198-080 CAP, CHIP 0.022
C313 87-010-180-080 C-CER 1500P
C314 87-010-180-080 C-CER 1500P
C315 87-010-178-080 CHIP CAP 1000P
C316 87-010-178-080 CHIP CAP 1000P
C317 87-A10-201-080 C-CAP,S0.33-16 KB
C318 87-A10-201-080 C-CAP,S0.33-16 KB
C319 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C320 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C321 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C322 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C324 87-010-260-080 CAP, ELECT 47-25V
C325 87-010-370-080 CAP,E 330-6.3 SME
C327 87-010-404-080 CAP, ELECT 4.7-50V
C328 87-010-404-080 CAP, ELECT 4.7-50V
C332 87-010-196-080 CHIP CAPACITOR,0.1-25
C335 87-010-401-080 CAP, ELECT 1-50V
DESCRIPTIONREF. NO. KANRI
– 6 –
Page 7
PART NO.
NO.
C336 87-010-401-080 CAP, ELECT 1-50V
C337 87-010-196-080 CHIP CAPACITOR,0.1-25
C339 87-010-196-080 CHIP CAPACITOR,0.1-25
C340 87-010-196-080 CHIP CAPACITOR,0.1-25
C351 87-012-140-080 CAP 470P
C352 87-012-140-080 CAP 470P
C354 87-010-175-080 CAP 560P
C355 87-012-349-080 C-CAP,S 1000P-50 CH
C356 87-010-260-080 CAP, ELECT 47-25V
C357 87-010-197-080 CAP, CHIP 0.01 DM
C358 87-010-183-080 C-CAP,S 2700P-50 B
C359 87-010-183-080 C-CAP,S 2700P-50 B
C360 87-010-183-080 C-CAP,S 2700P-50 B
C370 87-010-196-080 CHIP CAPACITOR,0.1-25
C371 87-010-175-080 CAP 560P
C372 87-010-175-080 CAP 560P
C373 87-010-179-080 CAP,CHIP S B1200P
C374 87-010-179-080 CAP,CHIP S B1200P
C375 87-010-545-080 CAP, ELECT 0.22-50V
C376 87-010-545-080 CAP, ELECT 0.22-50V
C378 87-010-196-080 CHIP CAPACITOR,0.1-25
C381 87-010-197-080 CAP, CHIP 0.01 DM
C382 87-010-318-080 C-CAP,S 47P-50 CH
C383 87-010-197-080 CAP, CHIP 0.01 DM
C384 87-010-402-080 CAP, ELECT 2.2-50V
C385 87-010-184-080 CHIP CAPACITOR 3300P(K)
C386 87-010-196-080 CHIP CAPACITOR,0.1-25
C388 87-012-156-080 C-CAP,S 220P-50 CH
C501 87-010-263-080 CAP, ELECT 100-10V
C502 87-010-196-080 CHIP CAPACITOR,0.1-25
C503 87-016-460-080 C-CAP,S 0.22-16 B
C504 87-016-460-080 C-CAP,S 0.22-16 B
C505 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C506 87-010-184-080 CHIP CAPACITOR 3300P(K)
C507 87-A11-550-080 C-CAP,S 820P-50 K B
C508 87-016-669-080 C-CAP,S 0.1-25 K B
C509 87-016-669-080 C-CAP,S 0.1-25 K B
C510 87-010-184-080 CHIP CAPACITOR 3300P(K)
C511 87-A11-550-080 C-CAP,S 820P-50 K B
C512 87-016-460-080 C-CAP,S 0.22-16 B
C513 87-010-544-080 CAP, ELECT 0.1-50V
C514 87-010-374-080 CAP, ELECT 47-10V
C515 87-010-401-080 CAP, ELECT 1-50V
C516 87-010-401-080 CAP, ELECT 1-50V
C517 87-010-183-080 C-CAP,S 2700P-50 B
C518 87-010-183-080 C-CAP,S 2700P-50 B
C531 87-010-560-080 CAP,E 10-50 GAS
C532 87-010-196-080 CHIP CAPACITOR,0.1-25
C533 87-010-196-080 CHIP CAPACITOR,0.1-25
C534 87-012-156-080 C-CAP,S 220P-50 CH
C535 87-010-178-080 CHIP CAP 1000P
C536 87-010-196-080 CHIP CAPACITOR,0.1-25
C538 87-010-318-080 C-CAP,S 47P-50 CH
C541 87-010-178-080 CHIP CAP 1000P
C603 87-010-318-080 C-CAP,S 47P-50 CH
C604 87-010-318-080 C-CAP,S 47P-50 CH
C605 87-010-318-080 C-CAP,S 47P-50 CH
C606 87-010-318-080 C-CAP,S 47P-50 CH
C611 87-010-956-080 CHIP-CAP,S 0.068-25B
C612 87-010-369-080 C-CAP,S 0.033-25 K B
C613 87-010-197-080 CAP, CHIP 0.01 DM
C614 87-016-669-080 C-CAP,S 0.1-25 K B
C616 87-010-180-080 C-CER 1500P
C617 87-010-198-080 CAP, CHIP 0.022
C618 87-010-401-080 CAP, ELECT 1-50V
C619 87-010-263-080 CAP, ELECT 100-10V
C620 87-016-669-080 C-CAP,S 0.1-25 K B
C621 87-010-197-080 CAP, CHIP 0.01 DM
C623 87-010-401-080 CAP, ELECT 1-50V
C624 87-010-401-080 CAP, ELECT 1-50V
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C626 87-010-992-080 C-CAP,S 0.047-25 B
C627 87-010-400-080 CAP, ELECT 0.47-50V
C628 87-010-400-080 CAP, ELECT 0.47-50V
C629 87-010-992-080 C-CAP,S 0.047-25 B
C630 87-010-383-080 CAP, ELECT 33-25V
C631 87-010-185-080 C-CAP,S 3900P-50 B
C632 87-010-185-080 C-CAP,S 3900P-50 B
C634 87-010-196-080 CHIP CAPACITOR,0.1-25
C635 87-A10-307-080 CAP,M 0.1-50 J
C636 87-A10-307-080 CAP,M 0.1-50 J
C637 87-A10-307-080 CAP,M 0.1-50 J
C638 87-A10-307-080 CAP,M 0.1-50 J
C639 87-010-405-080 CAP, ELECT 10-50V
C641 87-010-401-080 CAP, ELECT 1-50V
C642 87-010-401-080 CAP, ELECT 1-50V
C643 87-010-196-080 CHIP CAPACITOR,0.1-25
C644 87-010-401-080 CAP, ELECT 1-50V
C671 87-010-322-080 C-CAP,S 100P-50 CH
C672 87-010-322-080 C-CAP,S 100P-50 CH
C673 87-010-197-080 CAP, CHIP 0.01 DM
C675 87-010-196-080 CHIP CAPACITOR,0.1-25
C679 87-010-196-080 CHIP CAPACITOR,0.1-25
C680 87-010-197-080 CAP, CHIP 0.01 DM
C682 87-010-196-080 CHIP CAPACITOR,0.1-25
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-010-197-080 CAP, CHIP 0.01 DM
C773 87-010-184-080 CHIP CAPACITOR 3300P(K)
C774 87-010-184-080 CHIP CAPACITOR 3300P(K)
C779 87-010-186-080 C-CAP,S 4700P-50 KB
C780 87-010-186-080 C-CAP,S 4700P-50 KB
C782 87-010-197-080 CAP, CHIP 0.01 DM
C783 87-010-197-080 CAP, CHIP 0.01 DM
C784 87-010-197-080 CAP, CHIP 0.01 DM
C785 87-010-197-080 CAP, CHIP 0.01 DM
C786 87-010-197-080 CAP, CHIP 0.01 DM
C788 87-010-149-080 C-CAP,S 5P-50 CH
C789 87-012-365-080 C-CAP,S 0.027-25VBK
C790 87-012-365-080 C-CAP,S 0.027-25VBK
C791 87-010-196-080 CHIP CAPACITOR,0.1-25
C792 87-010-197-080 CAP, CHIP 0.01 DM
C793 87-010-404-080 CAP, ELECT 4.7-50V
C795 87-010-197-080 CAP, CHIP 0.01 DM
C796 87-010-197-080 CAP, CHIP 0.01 DM
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-010-197-080 CAP, CHIP 0.01 DM
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-012-369-080 C-CAP,S 0.047-50F
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-012-369-080 C-CAP,S 0.047-50F
C803 87-010-198-080 CAP, CHIP 0.022
C804 87-010-263-080 CAP, ELECT 100-10V
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C811 87-010-403-080 CAP, ELECT 3.3-50V
C812 87-010-403-080 CAP, ELECT 3.3-50V
C814 87-010-197-080 CAP, CHIP 0.01 DM
C815 87-010-400-080 CAP, ELECT 0.47-50V
C816 87-010-400-080 CAP, ELECT 0.47-50V
C818 87-010-180-080 C-CAP,S 1500P-50 KB
C819 87-010-179-080 CAP,CHIP S B1200P
C820 87-010-179-080 CAP,CHIP S B1200P
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-012-349-080 C-CAP,S 1000P-50 CH
C824 87-010-405-080 CAP, ELECT 10-50V
C825 87-010-596-080 CAP, S 0.047-16
C831 87-010-406-080 CAP,E 22-50V
C849 87-010-196-080 C-CAP,S 0.1-25 ZF
C869 87-010-197-080 C-CAP,S 0.01-25 KB
DESCRIPTIONREF. NO. KANRI
– 7 –
Page 8
PART NO.
NO.
C870 87-018-131-080 CAP,TC U 1000P-50 KB
C871 87-012-156-080 C-CAP,S 220P-50 CH
C872 87-012-156-080 C-CAP,S 220P-50 CH
C873 87-012-140-080 C-CAP,S 470P-50 CH
C874 87-010-405-080 CAP,E 10-50 SME
C875 87-010-196-080 C-CAP,S 0.1-25 ZF
C876 87-010-405-080 CAP,E 10-50 SME
C877 87-010-197-080 C-CAP,S 0.01-25 KB
C878 87-010-316-080 C-CAP,S 33P-50 CH
C879 87-010-314-080 C-CAP, S 22P-50 CH
C940 87-010-197-080 C-CAP, S 0.01-25 KB
C942 87-010-149-080 C-CAP, S 5P-50 CH
C947 87-010-197-080 C-CAP, S 0.01-25 KB
C948 87-012-140-080 C-CAP, S 470P-50 CH
C952 87-010-197-080 C-CAP, S 0.01-25 KB
C957 87-010-311-080 C-CAP, S 12P-50 CH
C958 87-010-197-080 C-CAP, S 0.01-25 KB
C985 87-010-322-080 C-CAP, S 100P-50 CH
C989 87-010-197-080 C-CAP, S 0.01-25 KB
C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C962 87-010-401-080 CAP,E 1-50 SME
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-010-197-080 CAP, CHIP 0.01 DM
C974 87-010-197-080 CAP, CHIP 0.01 DM
C979 87-010-322-080 C-CAP,S 100P-50 CH
C981 87-010-260-080 CAP, ELECT 47-25V
C982 87-010-196-080 CHIP CAPACITOR,0.1-25
C983 87-010-197-080 CAP, CHIP 0.01 DM
C984 87-010-197-080 CAP, CHIP 0.01 DM
C987 87-010-197-080 CAP, CHIP 0.01 DM
C991 87-010-312-080 C-CAP,S 15P-50 CH
C992 87-010-312-080 C-CAP,S 15P-50 CH
C993 87-010-178-080 CHIP CAP 1000P
C995 87-010-178-080 CHIP CAP 1000P
C997 87-010-196-080 CHIP CAPACITOR,0.1-25
C998 87-010-260-080 CAP, ELECT 47-25V
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-423-010 FLTR, CF SFE10.7MS3G-A
CF832 82-785-747-010 CF,MS2GHY,R
CN1 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3
CN91 87-A60-619-010 CONN,2P V 2MM JMT
CN92 87-A60-619-010 CONN,2P V 2MM JMT
CN101 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3
CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-A60-131-010 CONN,6P V FE
CN605 87-099-568-010 CONN,11P TUC-P11P-B1
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)
CNA2 8A-NF3-640-110 CONN ASSY,3P (VM) ANF-3
FB161 87-003-223-080 F-BEAD,BL02RN2
FB162 87-003-223-080 F-BEAD,BL02RN2
FB301 87-008-372-080 FILTER, EMI BLOIRNI
FB501 87-008-372-080 FILTER, EMI BLOIRNI
FFC302 88-906-481-110 FF-CABLE,6P 1.25 480MM
FFE831 A8-6ZA-191-130 6ZA-1 FEENM
J102 87-A60-238-010 TERMINAL,SP 4P (MSC)
J103 87-A60-483-010 JACK,DIA6.3 BLK ST W/S KM
J601 87-A60-885-010 JACK,PIN 6P R/W MSC
J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05
JW991 87-003-216-080 F-BEAD,-3.6-5 BL01RN1-A62T5
L101 87-A50-610-010 COIL,1UH K(MDEC)
L102 87-A50-610-010 COIL,1UH K(MDEC)
L301 87-A50-049-010 COIL,TRAP 85K(COI)
L302 87-A50-049-010 COIL,TRAP 85K(COI)
L351 87-007-342-010 COIL,OSC 85K BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L821 87-A50-209-010 COIL,1POLE MPX(MIT)
L822 87-A50-209-010 COIL,1POLE MPX(MIT)
L832 87-005-847-080 COIL,2.2UH(CECS)
L861 87-005-847-080 COIL,2.2UH K CECS
L941 87-A50-020-010 COIL,ANT LW (COI) 252KHZ
L942 87-A50-019-010 COIL,OSC LW (COI) 856KHZ
L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)
R117 87-012-142-080 C-CAP,S 0.33-16 ZF
R118 87-012-142-080 C-CAP,S 0.33-16 ZF
R161 87-A00-441-050 RES,270-1/2W J RP
R162 87-A00-441-050 RES,270-1/2W J RP
R163 87-A00-441-050 RES,270-1/2W J RP
R164 87-A00-441-050 RES,270-1/2W J RP
R790 87-010-197-080 CAP, CHIP 0.01 DM
R991 87-010-322-080 C-CAP,S 100P-50 CH
R993 87-010-322-080 C-CAP,S 100P-50 CH
R995 87-010-322-080 C-CAP,S 100P-50 CH
SFR301 87-024-355-080 SFR,33K DIA6 H
SFR302 87-024-355-080 SFR,33K DIA6 H
SFR303 87-024-355-080 SFR,33K DIA6 H
SFR304 87-024-355-080 SFR,33K DIA6 H
SFR305 87-024-356-080 SFR,47K DIA6 H
SFR306 87-024-356-080 SFR,47K DIA6 H
SFR351 87-024-356-080 SFR,47K DIA6 H
SFR352 87-024-356-080 SFR,47K DIA6 H
TC942 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECRLA
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P
X861 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
DISPLAY C.B
C103 87-010-196-080 CHIP CAPACITOR,0.1-25
C104 87-010-313-080 CAP, CHIP 18P
C105 87-010-322-080 C-CAP,S 100P-50 CH
C106 87-012-145-080 CAP, CHIP S 270P CH
C107 87-012-157-080 C-CAP,S 330P-50 CH
C108 87-015-681-040 E/CAP 10-16
C109 87-010-401-040 CAP,E 1-50 SME
C110 87-010-196-080 CHIP CAPACITOR,0.1-25
C112 87-016-460-080 C-CAP,S 0.22-16 B
C113 87-A10-189-040 CAP,E 220-10
C114 87-010-196-080 CHIP CAPACITOR,0.1-25
C115 87-010-198-080 CAP, CHIP 0.022
C116 87-010-493-040 CAP,E 0.47-50 GAS
C117 87-010-498-040 CAP,E 10-16 GAS
C118 87-010-194-080 CAP, CHIP 0.047
C119 87-A10-797-040 CAP,E 47-35 M 5L SRM
C120 87-015-699-040 CAP,E 10-50 7L
C121 87-015-699-040 CAP,E 10-50 7L
C122 87-010-197-080 CAP, CHIP 0.01 DM
C123 87-010-196-080 CHIP CAPACITOR,0.1-25
C125 87-010-196-080 CHIP CAPACITOR,0.1-25
C128 87-010-178-080 CHIP CAP 1000P
C129 87-010-194-080 CAP, CHIP 0.047
C131 87-A10-189-040 CAP,E 220-10
C132 87-A10-189-040 CAP,E 220-10
C151 87-010-194-080 CAP, CHIP 0.047
C192 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C196 87-010-194-080 CAP, CHIP 0.047
C197 87-010-194-080 CAP, CHIP 0.047
C213 87-A10-189-040 CAP,E 220-10
C301 87-010-318-080 C-CAP,S 47P-50 CH
C303 87-016-460-080 C-CAP,S 0.22-16 B
C304 87-016-460-080 C-CAP,S 0.22-16 B
C305 87-010-196-080 CHIP CAPACITOR,0.1-25
C306 87-010-196-080 CHIP CAPACITOR,0.1-25
DESCRIPTIONREF. NO. KANRI
– 8 –
Page 9
PART NO.
NO.
C310 87-010-067-040 CAP,E 0.1-50 5L
C701 87-010-981-040 CAP,E 22-35 5L SRE
C901 87-012-157-080 C-CAP,S 330P-50 CH
C902 87-010-176-080 C-CAP,S 680P-50 SL
C903 87-010-176-080 C-CAP,S 680P-50 SL
C904 87-010-176-080 C-CAP,S 680P-50 SL
C905 87-010-176-080 C-CAP,S 680P-50 SL
C906 87-010-176-080 C-CAP,S 680P-50 SL
C907 87-010-176-080 C-CAP,S 680P-50 SL
C908 87-010-176-080 C-CAP,S 680P-50 SL
C909 87-010-176-080 C-CAP,S 680P-50 SL
C910 87-010-176-080 C-CAP,S 680P-50 SL
C911 87-010-176-080 C-CAP,S 680P-50 SL
C912 87-010-176-080 C-CAP,S 680P-50 SL
C913 87-010-176-080 C-CAP,S 680P-50 SL
C914 87-012-145-080 CAP, CHIP S 270P CH
CN101 87-099-720-010 CONN,30P TYK-B(P)
CN102 87-A60-054-010 CONN,14P V 9604S-14C
CN103 87-099-750-010 CONN,15P V 9604SC
CN601 87-A60-062-010 CONN,05P V 9604S-05C
CN701 87-099-750-010 CONN,15P V 9604SC
FFC102 88-914-481-110 FF-CABLE,14P 1.25 480MM
FFC104 88-915-161-110 FF-CABLE,15P 1.25
FFC601 88-905-081-110 FF-CABLE,5P 1.25
FFC701 88-915-161-110 FF-CABLE,15P 1.25
FL101 8A-NF3-613-010 FL,BJ752GK-ANF3
JW315 87-A90-896-080 F-BEAD, 035600STY7
JW316 87-A90-896-080 F-BEAD, 035600STY7
L101 87-A50-333-010 COIL,OSC 9.43MHZ
CD KEY C.B
CN301 87-A60-079-010 CONN,08P H 9604S-08F
FFC302 88-908-381-110 FF-CABLE,8P 1.25
LED311 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED312 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED313 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED314 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED315 87-A40-380-180 LED,SEL6510C-TP5 GRN
S311 87-A90-095-080 SW,TACT EVQ11G04M
S312 87-A90-095-080 SW,TACT EVQ11G04M
S313 87-A90-095-080 SW,TACT EVQ11G04M
S314 87-A90-095-080 SW,TACT EVQ11G04M
S315 87-A90-095-080 SW,TACT EVQ11G04M
S316 87-A90-095-080 SW,TACT EVQ11G04M
S317 87-A90-095-080 SW,TACT EVQ11G04M
CONTROL C.B
C401 87-010-196-080 CHIP CAPACITOR,0.1-25
C407 87-010-322-080 C-CAP,S 100P-50 CH
C410 87-010-196-080 CHIP CAPACITOR,0.1-25
C417 87-010-322-080 C-CAP,S 100P-50 CH
C423 87-010-196-080 CHIP CAPACITOR,0.1-25
C424 87-010-196-080 CHIP CAPACITOR,0.1-25
C501 87-010-178-080 CHIP CAP 1000P
C502 87-012-156-080 C-CAP,S 220P-50 CH
C531 87-010-196-080 CHIP CAPACITOR,0.1-25
C532 87-010-196-080 CHIP CAPACITOR,0.1-25
CN104 87-099-750-010 CONN,15P V 9604SC
CN302 87-A60-059-010 CONN,08P V 9604S-08C
LED101 87-A40-317-080 LED,SLR-342VCT31 RED
LED421 87-A40-831-010 LED,SELU1E10CXM-LF70 BLUE-DEF
LED422 87-A40-831-010 LED,SELU1E10CXM-LF70 BLUE-DEF
LED440 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED441 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED442 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED443 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED444 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED445 87-A40-380-180 LED,SEL6510C-TP5 GRN
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
LED446 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED447 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED448 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED449 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED451 87-A40-537-040 LED,SLR-56PT-T31-W
LED452 87-A40-537-040 LED,SLR-56PT-T31-W
LED453 87-A40-537-040 LED,SLR-56PT-T31-W
LED454 87-A40-537-040 LED,SLR-56PT-T31-W
LED455 87-A40-537-040 LED,SLR-56PT-T31-W
LED456 87-A40-537-040 LED,SLR-56PT-T31-W
LED461 87-A40-317-080 LED,SLR-342VCT31 RED
LED462 87-A40-317-080 LED,SLR-342VCT31 RED
LED463 87-A40-317-080 LED,SLR-342VCT31 RED
LED464 87-A40-317-080 LED,SLR-342VCT31 RED
LED465 87-A40-317-080 LED,SLR-342VCT31 RED
LED521 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF
LED522 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF
S201 87-A90-095-080 SW,TACT EVQ11G04M
S202 87-A90-095-080 SW,TACT EVQ11G04M
S203 87-A90-095-080 SW,TACT EVQ11G04M
S204 87-A90-095-080 SW,TACT EVQ11G04M
S205 87-A90-095-080 SW,TACT EVQ11G04M
S206 87-A90-095-080 SW,TACT EVQ11G04M
S207 87-A90-095-080 SW,TACT EVQ11G04M
S208 87-A90-095-080 SW,TACT EVQ11G04M
S211 87-A90-095-080 SW,TACT EVQ11G04M
S214 87-A90-095-080 SW,TACT EVQ11G04M
S216 87-A90-095-080 SW,TACT EVQ11G04M
S217 87-A90-095-080 SW,TACT EVQ11G04M
S221 87-A90-095-080 SW,TACT EVQ11G04M
S222 87-A90-095-080 SW,TACT EVQ11G04M
S223 87-A90-095-080 SW,TACT EVQ11G04M
S224 87-A90-095-080 SW,TACT EVQ11G04M
S225 87-A90-095-080 SW,TACT EVQ11G04M
S228 87-A90-095-080 SW,TACT EVQ11G04M
S229 87-A90-095-080 SW,TACT EVQ11G04M
S230 87-A90-095-080 SW,TACT EVQ11G04M
S231 87-A90-095-080 SW,TACT EVQ11G04M
S232 87-A90-095-080 SW,TACT EVQ11G04M
S234 87-A90-095-080 SW,TACT EVQ11G04M
S241 87-A90-095-080 SW,TACT EVQ11G04M
S242 87-A90-095-080 SW,TACT EVQ11G04M
S243 87-A90-095-080 SW,TACT EVQ11G04M
S244 87-A90-095-080 SW,TACT EVQ11G04M
S245 87-A90-095-080 SW,TACT EVQ11G04M
S246 87-A90-095-080 SW,TACT EVQ11G04M
S247 87-A90-095-080 SW,TACT EVQ11G04M
S248 87-A90-095-080 SW,TACT EVQ11G04M
S249 87-A90-095-080 SW,TACT EVQ11G04M
S250 87-A90-095-080 SW,TACT EVQ11G04M
S251 87-A90-095-080 SW,TACT EVQ11G04M
S252 87-A90-095-080 SW,TACT EVQ11G04M
S253 87-A90-095-080 SW,TACT EVQ11G04M
SW501 87-A91-739-010 SW,RTRY EC12E12404-25MM RT
VOLUME C.B
C161 87-010-178-080 CHIP CAP 1000P
C162 87-012-156-080 C-CAP,S 220P-50 CH
S511 87-A90-095-080 SW,TACT EVQ11G04M
S512 87-A90-095-080 SW,TACT EVQ11G04M
S513 87-A90-095-080 SW,TACT EVQ11G04M
S514 87-A90-095-080 SW,TACT EVQ11G04M
S515 87-A90-095-080 SW,TACT EVQ11G04M
SW101 87-A91-740-010 SW,RTRY EC12E24308-30MM
MIC C.B
C601 87-010-196-080 CHIP CAPACITOR,0.1-25
C602 87-010-186-080 CAP,CHIP 4700P
DESCRIPTIONREF. NO. KANRI
– 9 –
Page 10
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
C603 87-010-112-040 CAP,E 100-16
C604 87-010-405-040 CAP,E 10-50
C605 87-010-546-040 CAP,E 0.33-50
C606 87-010-320-080 CHIP CAP 68P
C608 87-012-157-080 C-CAP,S 330P-50 CH
C621 87-010-178-080 CHIP CAP 1000P
CN602 87-A60-082-010 CONN,05P H 9604S-05F
J601 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
J602 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
L601 87-003-098-080 COIL,2.2UH
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
R162 87-A00-418-010 RES,M/F 0.15-3W J
R165 87-A00-418-010 RES,M/F 0.15-3W J
R166 87-A00-418-010 RES,M/F 0.15-3W J
R231 87-A00-258-080 RES,M/F 0.22-1W J
R232 87-A00-258-080 RES,M/F 0.22-1W J
R243 87-A00-258-080 RES,M/F 0.22-1W J
R244 87-A00-258-080 RES,M/F 0.22-1W J
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
WH101 87-A90-460-010 HLDR,WIRE 2.5-7P
AMP C.B
C101 87-010-188-080 CAP,CHIP 6800P
C102 87-010-188-080 CAP,CHIP 6800P
C103 87-010-405-080 CAP, ELECT 10-50V
C104 87-010-405-080 CAP, ELECT 10-50V
C107 87-010-404-080 CAP, ELECT 4.7-50V
C108 87-010-404-080 CAP, ELECT 4.7-50V
C111 87-010-322-080 C-CAP,S 100P-50 CH
C112 87-010-322-080 C-CAP,S 100P-50 CH
C113 87-A10-812-080 C-CAP,S 220P-200 J CH
C114 87-A10-812-080 C-CAP,S 220P-200 J CH
C119 87-010-197-080 CAP, CHIP 0.01 DM
C120 87-010-197-080 CAP, CHIP 0.01 DM
C121 87-010-260-080 CAP, ELECT 47-25V
C122 87-010-260-080 CAP, ELECT 47-25V
C123 87-010-190-080 C-CAP,S 0.01-50 ZF
C173 87-010-186-080 CAP,CHIP 4700P
C174 87-010-186-080 CAP,CHIP 4700P
C205 87-010-187-080 CAP,CHIP S5600P
C206 87-010-187-080 CAP,CHIP S5600P
C207 87-010-403-080 CAP, ELECT 3.3-50V
C208 87-010-403-080 CAP, ELECT 3.3-50V
C209 87-010-184-080 CHIP CAPACITOR 3300P(K)
C210 87-010-184-080 CHIP CAPACITOR 3300P(K)
C211 87-010-401-080 CAP, ELECT 1-50V
C212 87-010-401-080 CAP, ELECT 1-50V
C215 87-012-156-080 C-CAP,S 220P-50 CH
C216 87-012-156-080 C-CAP,S 220P-50 CH
C217 87-010-260-080 CAP, ELECT 47-25V
C218 87-010-260-080 CAP, ELECT 47-25V
C221 87-016-100-080 CAP, ELECT 10-50 M BP SME
C222 87-016-100-080 CAP, ELECT 10-50 M BP SME
C223 87-010-197-080 CAP, CHIP 0.01 DM
C224 87-010-197-080 CAP, CHIP 0.01 DM
C249 87-012-368-080 C-CAP,S 0.1-50 F
C251 87-010-993-080 C-CAP,S 0.056-25 B
C252 87-010-196-080 CHIP CAPACITOR,0.1-25
C253 87-010-196-080 CHIP CAPACITOR,0.1-25
C254 87-010-993-080 C-CAP,S 0.056-25 B
C255 87-010-190-080 S CHIP F 0.01
C256 87-010-190-080 S CHIP F 0.01
C265 87-010-260-080 CAP,E 47-25V
C402 87-010-196-080 CHIP CAPACITOR,0.1-25
C413 87-A10-119-080 CAP,E 10-100 REA
C414 87-A10-119-080 CAP,E 10-100 REA
CNA101 8A-NF8-652-010 CONN ASSY,7P TID-A(480)
CNA103 8A-NF8-656-010 CONN ASSY,5P TID-A(400)
CON101 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3
CON102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3
FB101 87-A90-896-080 F-BEAD, 035600STY7
FB102 87-A90-896-080 F-BEAD, 035600STY7
J201 87-A61-148-010 JACK,PIN 4P R/W BLUE
JW124 87-A90-896-080 F-BEAD, 035600STY7
JW138 87-A90-896-080 F-BEAD, 035600STY7
JW944 87-A90-896-080 F-BEAD, 035600STY7
L251 87-A50-610-010 COIL,1UH K(MDEC)
L252 87-A50-610-010 COIL,1UH K(MDEC)
R161 87-A00-418-010 RES,M/F 0.15-3W J
PT C.B
C1 87-010-387-080 CAP,E 470-25 SME
C8 87-A11-148-080 CAP,TC U 0.1-50 Z F
C9 87-A11-148-080 CAP,TC U 0.1-50 Z F
C10 87-A11-148-080 CAP,TC U 0.1-50 Z F
C11 87-A11-148-080 CAP,TC U 0.1-50 Z F
C12 87-010-917-000 CAP,E 3300-50 M SMG
C13 87-010-917-000 CAP,E 3300-50 M SMG
C16 87-010-403-040 CAP,E 3.3-50 SME
C18 87-A11-148-080 CAP,TC U 0.1-50 Z F
C19 87-A11-148-080 CAP,TC U 0.1-50 Z F
C20 87-A11-148-080 CAP,TC U 0.1-50 Z F
C21 87-A11-148-080 CAP,TC U 0.1-50 Z F
C22 87-A10-231-090 CAP,E 3300-80
C23 87-A10-231-090 CAP,E 3300-80
C27 87-A11-148-080 CAP,TC U 0.1-50 Z F
C28 87-A11-148-080 CAP,TC U 0.1-50 Z F
C29 87-A11-148-080 CAP,TC U 0.1-50 Z F
C30 87-A11-148-080 CAP,TC U 0.1-50 Z F
C31 87-A11-148-080 CAP,TC U 0.1-50 Z F
C32 87-A11-148-080 CAP,TC U 0.1-50 Z F
C33 87-A11-148-080 CAP,TC U 0.1-50 Z F
C34 87-A11-148-080 CAP,TC U 0.1-50 Z F
C35 87-A11-148-080 CAP,TC U 0.1-50 Z F
C36 87-A11-148-080 CAP,TC U 0.1-50 Z F
C37 87-A11-148-080 CAP,TC U 0.1-50 Z F
C38 87-A11-148-080 CAP,TC U 0.1-50 Z F
!
CN1 87-A61-110-010 CONN,9P V TID-A
!
CN2 87-A61-108-010 CONN,5P V TID-A
!
F101 87-035-459-010 FUSE,5A 250V
!
F102 87-035-459-010 FUSE,5A 250V
!
FB101 87-A90-562-010 F-BEAD,9.5-17.5.5-28.5 BRH
!
FC1 87-033-213-080 FUSE CLAMP,PFC5000
!
FC2 87-033-213-080 FUSE CLAMP,PFC5000
!
PR1 87-026-682-080 PROTECTOR,10A 60V491
!
PR2 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
!
PR3 87-A90-195-080 PROTECTOR,7A 125V 49
!
PR4 87-A90-195-080 PROTECTOR,7A 125V 49
!
PR5 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
!
PR8 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
!
PT2 8A-NF8-622-010 PT,SUB ANF-8 (E)
!
PT101 8A-NF3-602-010 PT,LH EI105-60 ANF-3
!
RY1 87-A90-976-010 RELAY,AC 12V SDT-S-112LMR
!
T1 87-A60-317-010 TERMINAL, 1P MSC
!
T2 87-A60-317-010 TERMINAL, 1P MSC
VM C.B
CNA3 87-049-919-010 CONN,3P EH V WHT
GEQ C.B
C201 87-010-402-080 CAP, ELECT 2.2-50V
C202 87-010-402-080 CAP, ELECT 2.2-50V
C205 87-010-404-080 CAP, ELECT 4.7-50V
C207 87-016-669-080 C-CAP,S 0.1-25 K B
C208 87-016-669-080 C-CAP,S 0.1-25 K B
C209 87-016-460-080 C-CAP,S 0.22-16 B
– 10 –
Page 11
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
C210 87-016-460-080 C-CAP,S 0.22-16 B
C211 87-012-365-080 C-CAP,S 0.027-25VBK
C212 87-012-365-080 C-CAP,S 0.027-25VBK
C213 87-010-956-080 CHIP-CAP,S 0.068-25B
C214 87-010-956-080 CHIP-CAP,S 0.068-25B
C215 87-010-197-080 CAP, CHIP 0.01 DM
C216 87-010-197-080 CAP, CHIP 0.01 DM
C217 87-010-198-080 CAP, CHIP 0.022
C218 87-010-198-080 CAP, CHIP 0.022
C219 87-010-183-080 C-CAP,S 2700P-50 B
C220 87-010-183-080 C-CAP,S 2700P-50 B
C221 87-010-188-080 CAP,CHIP 6800P
C222 87-010-188-080 CAP,CHIP 6800P
C223 87-010-178-080 CHIP CAP 1000P
C224 87-010-178-080 CHIP CAP 1000P
C225 87-010-182-080 C-CAP,S 2200P-50 B
C226 87-010-182-080 C-CAP,S 2200P-50 B
C227 87-010-112-080 CAP, ELECT 100-16V
C228 87-010-196-080 CHIP CAPACITOR,0.1-25
C229 87-010-322-080 C-CAP,S 100P-50 CH
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C230 87-010-322-080 C-CAP,S 100P-50 CH
C231 87-010-322-080 C-CAP,S 100P-50 CH
CN201 87-A60-546-010 CONN,11P H GRY TUC-P11X-C1
DECK C.B
CN502 87-099-756-010 CONN,15P 9604S F
SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-036-110-010 SW,MICRO SPPB62
HEAD-1 C.B
HEAD-2 C.B
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
Resistor Code
0.55
108
118
128
: A
: A
– 11 –
Page 12
TRANSISTOR ILLUSTRATION
KTA1266GR
KTC3198GR
KTC3199GR
B C E
2SB1370E
FN1016
FP1016
E C B
CSA952K
CD1585BC
CSC4115BC
E C B
CC5551
E C B
2SB1237Q
E C B
DTC114ES
2SA933S
G D S
2SK3053
E C B
2SB1436(R)
D
G
S
2SK2158
2SJ461-T1
B
2SA1235F
2SC2714O
2SC3052F
CMBT5551
CMBT5401
CSD1306E
C
E
DTA143EKA
KRA104S
RT1N141C
RT1P141C
RT1P144C
RT1P441C
S
D
G
2SK360E
– 12 –
Page 13
WIRING - 1 (MAIN)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 13 –
R
S
T
U
Page 14
SCHEMATIC DIAGRAM 1 (MAIN 1/3 / VM)
14
Page 15
SCHEMATIC DIAGRAM 2 (MAIN 2/3)
15
Page 16
SCHEMATIC DIAGRAM 3 (MAIN 3/3 / HEAD-1 / HEAD-2)
16
Page 17
WIRING - 2 (DISPLAY / CD KEY)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 17 –
R
S
T
U
Page 18
SCHEMATIC DIAGRAM 4 (DISPLAY / CD KEY / DECK)
18
Page 19
WIRING - 3 (CONTROL \ VOLUME \ MIC)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 19 –
R
S
T
U
Page 20
SCHEMATIC DIAGRAM 5 (CONTROL / VOLUME / MIC)
20
Page 21
WIRING - 4 (AMP)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 21 –
R
S
T
U
Page 22
SCHEMATIC DIAGRAM 6 (AMP)
22
Page 23
WIRING - 5 (DECK / HEAD-1 / HEAD-2)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 23 –
R
S
T
U
Page 24
SCHEMATIC DIAGRAM 7 (GEQ)
24
Page 25
WIRING - 6 (PT / VM / GEQ)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 25 –
R
S
T
U
Page 26
SCHEMATIC DIAGRAM – 8 (PT)
– 26 –
Page 27
IC BLOCK DIAGRAM
27
Page 28
28
Page 29
29
Page 30
30
Page 31
27
Page 32
FL (BJ752GK-ANF3) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
– 32 –
Page 33
ANODE CONNECTION
– 33 –
Page 34
IC DESCRIPTION
IC, LC876596W-5P49
Pin No.
1 CLK O Common serial CLOCK output.
2 DATA O Common Serial DATA output.
3 STB O Common serial STROBE output.
4 CS-RHYTHM O Rhythm IC chip select output.
5 GEQ-CE O GEQ IC chip enable output.
6 HP-MUTE I Headphone plug-in detect input. (Output "L" at HOLD)
7 O-POWER O System power ON/OFF output. (Active "H")
8 PLL-CE O Tuner PLL IC chip enable output.
9 O-MUTE O System mute ON/OFF output.
10 I-MIC I Auto-VF MIC level special A/D input. (Output "L" at HOLD)
11 RESET I Reset input.
12 VOL-JOG I Main volume JOG rotary encoder A/D input.
13 MULTI-JOG I MULTI JOG rotary encoder A/D input.
14 VSS1 – Connected to GND.
15 CF 1
16 CF2
17 VDD1 – Power supply.
Pin Name I/O
– 9.43MHz oscillator circuit.
Description
18 HOLD I Power supply voltage detect A/D input.
19 ~ 22 KEY 1 ~ 4 I KEY 1 ~ 4 A/D input. (Output "L" at HOLD)
23 I-CDSW I CD mechanism SW A/D input. (Output "L" at HOLD)
24 I-DISH I CD turntable photo sensor A/D input. (Output "L" at HOLD)
25 I-SPEANA I SPEANA level A/D input. (Output "L" at HOLD)
26 I-RDSCLK/I-WRQ I TUNER RDS IC CLK (INT2) input / CD WRQ input. (Output "L" at HOLD&INI)
27 I-TU-SIG/MS I Tuner tuning signal level A/D input / Deck MS SENS. (Output "L" at HOLD)
28 I-TMBASE I Timebase clock (8Hz) input. (Output "L" at HOLD)
29 I-RMC I Remote control signal input. Active: "L". (Output "L" at HOLD)
30 ~ 42 G13 ~ G1 O FL grid G13 ~ G1 output.
43 ~ 45 P39 ~ P37 O FL segment P39 ~ P37 output.
46 VDD3 – Power supply.
47 P36/SPEANA A O FL segment P36 output / SPEANA band select output (A) .
48 P35/SPEANA B O FL segment P35 output / SPEANA band select output (B) .
49 P34/SPEANA C O FL segment P34 output / SPEANA band select output (C).
50 P33 O FL segment P33 output.
51 VP – Power supply for FL.
52 ~ 59 P32 ~ P25 O FL segment P32~ P25 output.
60 P24/NO AC-DEMO I/O
FL segment P24 output / NO AC-DEMO at AC-IN diode input. (No store DEMO
mode.)
61 P23/CASINO-DEMO I/O FL segment P23 output / CASINO-DEMO select diode input.
62 P22/NO-ECO I/O FL segment P22 output / NO-ECO select input.
63 P21/NO-RHYTHM I/O FL segment P21 output / NO-RHYTHM select diode input.
64 P20/AC3-DPL I/O FL segment P20 output / AC3-DPL select diode input. (Not used.)
– 34 –
Page 35
Pin No.
65 P19/K-CON I/O FL segement P19 output / K-CON select diode input. (Not used.)
66 P18/RDS I/O FL segement P18 output / RDS select diode input. (Not used.)
67 P17/FM1 I/O FL segment P17 output / FM1 select diode input. (Not used.)
68 P16/SW I/O FL segment P16 output / SW step initial diode input. (Not used.)
69 P15/LW I/O FL segment P15output / LW stereo select diode input. (Not used.)
70 P14/AM-10K I/O FL segment P14 output /AM-10K select diode input.
71 P13/AM-ST I/O FL segment P13 output / AM-ST select diode input. (Not used.)
72 VDD4 – Power supply.
73~76 P12~P9 O FL segment P12~P9 output.
77 P8/REA I/O FL segment P8 ouput / REC enable (A) switch input (active: "L").
78 P7/CST1 I/O FL segment P7 output / Cassette (1) switch.
79 P6/CAM1 I/O FL segment P6 output / CAM (1) switch input (active: "L").
80 P5/AUTO2 I/O FL segment P5 output / Auto stop reel (2) pulse input.
81 P4/AUTO1 I/O FL segment P4 output / Auto stop reel (1) pulse input.
82 P3/CAM2 I/O FL segment P3 output / CAM (2) switch input. (active:"L").
83 P2/REB I/O FL segment P2 output / REC enable (B) switch input. (active:"L").
84 P1/CST2 I/O FL segment P1 output / Cassette (2) switch input. (active:"L").
85 K-SCAN O Key scan output. (active:"L").
Pin Name
I/O Description
86 SOL1 O DECK (1) solenoid ON/OFF output.
87 SOL2 O DECK (2) solenoid ON/OFF output.
88 O-MOTOR O Deck motor ON/OFF output .
89 VSS2 – Connected to GND.
90 VDD2 – Power supply.
91 O–DISHREV O CD turn table dish reverse output.
92 O-DISHFWD O CD turn table dish forward output.
93 O-OPEN O CD tray open output.
94 O-CLOSE O CD tray close output.
95 IFC-TU/I-SQDATA I Tuner tune/IF count input (active: "L") / CD SUB-Q data input.
96
97
98 CD-CE/
99 CLK (CD) O CD IC control clock output.
100 STB(SHIFT) O Shift register strobe output.
I-STEREO/I-DRF
(O-CLK-VCD)
O-DATA(CD)/
I-RDS DATA
IO BUSY (VCD)
I/O Tuner stereo detect input (active "L") / DRF input.
I/O CD IC control data output / Tuner RDS data input. (Not used.)
I/O CD chip enable output.
– 35 –
Page 36
ADJUSTMENT <TUNER/DECK/DISPLAY>
13
A MAIN C.B
SFR352
IC303
SFR302
SFR301
SFR303
TP8 (LCH)
TP9 (RCH)
4
5
7
8
9
14
SFR351
SFR306
SFR304
TP11
(LCH)
GND
GND
SFR305
16
L801
TP10 (RCH)
IC601
9
IC801
8
L802
24
TP2
(CLK)
9
TP3
L942
R815
TP4
4
3
TC942
(3/3)
L951
TP1
(VT)
4
L941
5
(1/3)
4
FFE831
B DISPLAY C.B
K DECK C.B
17
16
15
14
13
12
11
10
FL101
6
2
3
IC101
1
TP1
(K-SCAN)
TP2(GND)
L101
18
DECK–1 P,DECK-2 R/P/E HEAD
SFR1
10
– 36 –
11
REV
11
FWD
Page 37
< TUNER SECTION >
< DECK SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to MW 1602kHz and check that the test point is
2052kHz ± 45Hz.
2. MW VT Check
Settings : • Test point : TP1 (VT)
Method : Set to MW 1602kHz and MW 531kHz and check that
the test point is less than 8.0V(1602kHz) and more than
0.6V(531kHz).
3. LW VT Adjustment
Settings : • Test point : TP1 (VT)
• Adjustment location : L942
Method : Set to LW 144kHz and adjust L942 so that the test
points becomes 1.5V ± 0.05V.
Then set to LW 290kHz and check that the test point is
less than 8.0V.
4. LW Tracking Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L941............................... 144kHz
TC942............................ 290kHz
Method : Set up TC942 to center before adjustment. The level at
144kHz is adjusted to max. by L941. Then the level at
290kHz is adjusted to max. by TC942.
5. MW Tracking Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L951(1/3)........................ 999kHz
Method : Set to MW 999kHz and adjust L951(1/3) so that the test
point is max.
6. FM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to FM 108.0MHz and check that the test point is
less than 8.0V.
Set to FM 87.5MHz and check that the test point is
more than 0.5V.
7. FM Tracking Check
Settings : • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 98.0MHz and check that the test point is less
than 13dBµV.
10. Tape Speed Adjustment
Settings : • Test tape : TTA–100(3kHz)
• Test point : TP10(Rch), TP11(Lch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz(FWD) and ±
45Hz(REV) with respect to forward speed.
11. Head Azimuth Adjustment
Settings : • Test tape : TTA–300 (315/10kHz)
• Test point : TP10(Rch), TP11(Lch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back the 10kHz signal of the test tape and adjust
screw so that the output becomes maximum. Next,
perform on each FWD PLAY and REV PLAY mode.
12. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–300 (315/10kHz)
• Test point : TP10(Rch), TP11(Lch)
Method : Play back the 315Hz and 10kHz signals of the test tape
and check that the output ratio of the 10kHz signal with
respect to that of the 315Hz signal is within 0 ± 2dB.
13. PB Sensitivity Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–200 (400Hz)
• Test point : TP10(Rch), TP11(Lch)
• Adjustment location : SFR301 (DECK 1, Lch)
SFR302 (DECK 1, Rch)
SFR303 (DECK 2, Lch)
SFR304 (DECK 2, Rch)
Method : Play back the test tape and adjust SFRs so that the
output level of the test points become 245mV±10mV.
14. REC/PB Frequency Response Adjustment (DECK 2)
Settings : • Test tape : TTA–602 (Normal)
• Test point : TP10(Rch), TP11(Lch)
• Input signal : 1kHz / 10kHz (LINE IN)
• Adjustment location : SFR351 (Lch)
SFR352 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 12.5mV. Record and play back the 1kHz and
10kHz signals and adjust SFRs so that the output level
of the 10kHz signals becomes 0dB ± 0.5dB with respect
to that of the 1kHz signal.
8. MW IF Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location : L802
• Input level : Variable
Method : Adjust L802 so that the output becomes max.
9. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4
(DC Balance)
TP8(Lch), TP9(Rch)
(Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the
distortion is minimum.
Next, check that the voltage between TP3 and TP4 is
0V ± 0.3V.
– 37 –
15. REC/PB Frequency response Check (DECK 2)
Settings : • Test tape : TTA-615 (CrO
• Test point : TP10(Rch), TP11(Lch)
• Input signal : 1kHz/10kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 12.5mV. Record and play back the 1kHz and
10kHz signals and check that the output is 0dB ± 2dB.
)
2
Page 38
16. REC/PB Sensitivity Adjustment (DECK 2)
Settings : • Test tape : TTA–602 (Normal)
• Test point : TP10(Rch), TP11(Lch)
• Input signal : 1kHz (LINE IN)
• Adjustment location : SFR305 (Lch)
SFR306 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 125mV. Record the play back the 1kHz signal
and adjust SFRs so that the output level becomes 0dB ±
0.5dB
17. REC/PB Sensitivity Check (DECK 2)
Settings : • Test tape : TTA-615 (CrO
• Test point : TP10(Rch), TP11(Lch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 125mV. Record and play back the 1kHz signal
and check that the output is 0dB ± 1.5dB.
)
2
< DISPLAY SECTION >
18. µ-CON OSC Adjustment
Settings : • Test point : TP1(K-SCAN), TP2 (GND)
• Adjustment location : L101
Method : Insert AC plug with pressing TUNER function key.
Adjust L101 so that the frequency across the test
point is 208.8Hz ± 0.2Hz.
.
– 38 –
Page 39
MECHANICAL EXPLODED VIEW 1 / 1
– 39 –
Page 40
MECHANICAL PART LIST 1 / 1
PART NO.
NO.
1 88-NF3-090-010 RING,FOOT
2 8A-NF3-042-010 PANEL ASSY,TRAY
3 8A-NF3-029-010 BOX,CASS R
4 8A-NF3-040-010 PANEL,CASS R
5 8A-NF3-059-010 WINDOW,CASS R
6 8A-NF3-039-010 PANEL,CASS L
7 8A-NF3-058-010 WINDOW,CASS L
8 8A-NF3-028-010 BOX,CASS L
9 8A-NF3-090-010 REFLECTOR,CASS L
10 81-532-080-010 LABEL, CASS. COMPT
11 8A-NF3-091-010 REFLECTOR,CASS R
12 8A-NF3-048-010 PANEL,REFLECTOR- CD
13 8A-NF3-049-010 PANEL,KEY-CD
14 8A-NF3-047-010 PANEL,CD
15 8A-NF3-071-010 KEY,CD
16 8A-NF3-089-010 REFLECTOR,CD
17 8A-NF3-203-010 GUIDE,LED-CD
18 87-NF4-216-010 HLDR,LOCK 1
19 86-NF9-224-010 SPR-C,LOCK
20 82-NF5-229-010 PLATE,LOCK
21 87-NF8-220-010 DMPR,150
22 82-NF5-218-010 SPR-T,EJECT 1 (SIN)
23 8A-NF3-082-010 KNOB,RTRY JOG
24 8A-NF3-087-010 REFLECTOR,JOG
25 8A-NF3-078-010 RING,JOG U
26 8A-NF3-081-010 KNOB,RTRY VOL
27 8A-NF3-076-010 RING,VOL
28 8A-NF3-002-010 CABI,FR EZ
29 8A-NF3-051-010 WINDOW,DISP
30 8A-NF3-033-010 PANEL,FR EZ
31 8A-NF3-063-010 KEY ASSY,OPE
32 8A-NF3-066-110 KEY,REC
33 8A-NF3-065-010 KEY,KARAOKE
34 8A-NF3-061-010 KEY,GEQ
35 8A-NF3-068-010 KEY,JOG
36 8A-NF3-072-010 KEY,FUNC
37 8A-NF3-088-010 REFLECTOR,FUNC
38 8A-NF3-067-010 KEY,BBE
39 8A-NF3-062-010 KEY,DSP
40 8Z-NF3-210-010 GUIDE,FL
41 8A-NF3-070-010 KEY,ECO
42 8A-NF3-201-010 GUIDE,LED-FUNC
43 8A-NF3-213-110 HLDR,HT-SINK L
44 8A-NF3-214-010 HLDR,HT-SINK R
45 8A-NF3-210-010 HLDR,SIDE L
DESCRIPTIONREF. NO. KANRI
PART NO.
46 8A-NF3-208-010 HLDR,CHAS L
47 87-NF4-221-010 HLDR,CABLE
48 87-A91-423-010 FAN,AD0612DS-D7OGL
!
49 87-A80-148-010 AC CORD ASSY,E BLK
50 87-A90-562-010 F-BEAD,9.5-17.5-28.5 BRH
51 8A-NF3-209-010 HLDR,CHAS R
52 8A-NF3-211-010 HLDR,SIDE R
53 8A-NF3-229-110 HLDR,BRACKET
54 87-085-185-010 BUSHING, AC CORD (E)
55 8A-NF3-212-010 HLDR,REAR
56 84-ZG1-245-210 CAP,OPTICAL
57 8A-NF3-026-010 CABI,BOTTOM
58 8Z-NF3-048-010 COVER, BOTTOM
59 82-NF5-219-010 SPR-T,EJECT 2 (SIN)
60 87-NF4-217-110 HLDR,LOCK 2
61 87-064-185-010 HLDR,WIRE
62 8A-NF8-206-010 HLDR,PWB M
63 8A-NF3-221-010 HLDR,IC-VM
64 8A-NF3-225-010 COVER, HLDR
65 8A-NF3-223-010 HLDR,FAN
66 87-A91-711-010 FAN, 3110GL-B4W-B34-H02 -400MM
67 8A-NF3-014-010 CABI,REAR EZSM
68 8A-NF3-228-010 HLDR,PWB-PT
69 8A-NF3-027-010 CABI,STEEL
A 87-067-703-010 TAPPING SCREW, BVT2+3-10
B 87-067-581-010 TAPPING SCREW, BVT2+3-15
C 87-721-097-410 QT2+3-12 GLD
D 87-591-095-410 TAPPING SCREW, QIT+3-8 (GLD)
E 87-B10-190-010 BVT2+3-22 W/O SLOT
F 87-067-689-010 TAPPING SCREW, BVTT+3-8
G 87-067-761-010 TAPPING SCREW, BVT2+3-10
H 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
I 87-721-096-410 QT2+3-10 GLD
J 87-067-758-010 BVT2+3-12 W/O SLOT
K 87-067-975-010 S-SCREW,IT+4-8
L 87-067-641-010 UTT2+3-8(W/O SLOT)BL
M 87-067-579-010 TAPPING SCREW, BVT2+3-8
NO.
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange
– 40 –
Page 41
B
B
31
38
39
40
34
33
35
43
45
41
41
44
49
47
48
46
C
C
30
8
(DECK 1)
D
18
52
51
D
D
CAPSTAN N 2.2-41.5
DECK C.B
50
50
A
CUSH-G,DIA3.7-8-3.2
A
37
32
C
E
CUSH-G,DIA3.7-8-3.2
CAPSTAN N 2.2-41.7
SH,1.63-3.2-0.5 SLT
SH,
BELT D2
2ZM3MK2 PR4N
(BOTTOM SIDE)
2000/3/6 YPR4N
TAPE MECHANISM EXPLODED VIEW 1 / 1
14
15
A
12
3
2
5
11
9
6
10
13
17
A
4
16
19
20
B
B
42
PH(DECK 1)
RPH(DECK 2)
7
HEAD 1 C.B(DECK 1)
HEAD 2 C.B(DECK 2)
1
36
(DECK 1)
29
(DECK 2)
22
21
24
25
23
A
26
29
(DECK 2)
28
27
– 41 –
Page 42
TAPE MECHANISIM PARTS LIST 1 / 1
PART NO.
NO.
1 82-ZM3-301-610 1H CHAS ASSY,M2
2 82-ZM1-258-210 0E SPR-T,PINCH L
3 82-ZM1-341-210 1A LVR ASSY,PINCH L2
4 82-ZM1-333-210 0E PLATE,LINK2
5 82-ZM1-266-310 0E LVR,DIR
6 82-ZM1-214-010 0E SPR-T,DIR
7 82-ZM1-206-910 1A CHAS,HEAD
8 82-ZM3-335-310 0E PULLEY,COUPLER M3
9 82-ZM1-269-210 0E SPR-T,BRG
10 82-ZM1-219-110 0E SPR-T,LINK
11 82-ZM1-210-110 0E GEAR,H T
12 82-ZM1-213-010 0E SPR-T,HEAD
13 82-ZM1-207-910 1A GUIDE,TAPE
14 86-ZM4-206-010 0E S-SCREW,AZIMUTH L
15 82-ZM1-314-110 0E PLATE,HEAD
16 82-ZM1-208-310 0E HLDR,HEAD
17 82-ZM1-218-010 0E SPR-E,HB
18 82-ZM3-342-010 0E BELT,SBU MOT 3
19 82-ZM1-222-210 0E LVR,PLAY
20 82-ZM1-217-410 0E REEL TABLE
21 82-ZM1-244-510 0E SPR-C,BT
22 82-ZM1-285-410 0E SPR-C,BT L
23 82-ZM1-257-010 0E SPR-T,CAS
24 82-ZM1-241-310 0E LVR,MC
25 82-ZM1-242-010 0E LVR,CAS
26 82-ZM1-243-010 0E LVR,STOP
28 82-ZM1-259-210 0E SPR-T,PINCH R
29 82-ZM1-240-110 0E LVR,REC(*)
30 80-ZM6-243-010 0E SH 1.75-3.6-0.5 SLT
31 82-ZM1-255-310 0E SPR-E,LVR DIR
32 82-ZM3-305-210 0E GEAR,CAM M2
33 82-ZM1-227-310 0E LVR,TRIG
34 82-ZM3-306-110 0E LVR,FR M2
35 82-ZM1-265-310 0E SPR-E,TRIG
36 82-ZM3-339-110 0E SHAFT,COUPLER N3
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
37 86-ZM1-206-010 0E BELT,MAIN L
38 82-ZM1-322-010 0E SPR-T,FR 60
39 82-ZM1-220-210 0E GEAR,IDLER
40 82-ZM3-616-010 0E RING MAGNET 4
41 82-ZM1-216-410 0E GEAR,REEL
42 87-A90-820-010 1D HEAD,PH HADKH25 FPC
42 87-A90-821-010 1H HEAD,RPH HADKH56 FPC
43 82-ZM1-225-210 0E GEAR,FR
44 82-ZM1-226-010 0E GEAR,REW
45 82-ZM3-333-310 1A SLIP DISK ASSY 2
46 82-ZM1-338-110 0E BELT,FR 4
47 82-ZM1-349-110 1A FLY-WHL,R W
47 82-ZM1-348-110 0E FLY-WHL,L W
47 82-ZM3-338-310 1A FLY-WHL,R3W
48 82-ZM1-344-210 0E LVR ASSY,PINCH R2
49 82-ZM3-329-410 0E BELT,SBU R2
50 82-ZM1-618-410 1B SOL ASSY,27
51 87-045-347-010 1H MOT,SHU2L 70
52 82-ZM3-221-210 0E PULLEY,MOT 2M
A 85-ZM3-202-010 0E S-SCREW,TG
B 80-ZM6-207-010 0E V+1.6-7
C 82-ZM3-318-110 0E S-SCREW W,MOTOR M2
D 87-B10-043-010 0E W-P,0.99-4-0.25 SLT
E 82-ZM3-334-010 0E PW 2.16-6-0.4
DESCRIPTIONREF. NO. KANRI
– 42 –
Page 43
SPEAKER DISASSEMBLY INSTRUCTIONS
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 43 –
Fig-3
Page 44
SPEAKER PARTS LIST SX-WNT99 <YSL>
PART NO.
NO.
1 8A-NS3-001-010 PANEL,FR
2 8A-NS3-002-010 PANEL,TW L
3 8A-NS3-003-010 PANEL,TW R
4 8A-NS3-006-010 PANEL,TOP
5 8A-NS3-010-010 PROTECTOR,SQA
6 8A-NS3-011-010 PROTECTOR,TWA
7 8A-MS1-602-010 SPKR,W 200
8 8A-NS3-602-010 SPKR,M 100
9 8A-MS2-605-110 SPKR,TW 60
10 88-NSK-610-010 SPKR,CERAMIC ASSY
DESCRIPTIONREF. NO. KANRI
ACCESORIES / PACKAGE LIST
PART NO.
NO.
1 8A-NF3-906-010 IB,EZ (9L) M
2 87-006-225-010 AM LOOP ANT NC2
3 87-A90-118-010 ANT,FEEDER FM (Z)
4 8Z-NF5-702-010 RC UNIT,RC-ZAS04
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
11 88-NS5-610-010 CORD,SPKR
12 88-NS5-611-010 CORD,SPKR B/L
13 8A-NSJ-006-010 BADGE,AIWA S35
14 8A-NS3-014-010 CABI,TOP
15 8A-NS3-017-010 PANEL,RING S
16 8A-NS3-015-010 PANEL,DUCT S
DESCRIPTIONREF. NO. KANRI
– 44 –
Page 45
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9620450 9630472 0251431
Loading...