EAW NSX SZ309 Service Manual

NSX-SZ300

HS,HT

NSX-SZ309
NSX-SZ329

HA

LH

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

CD

CASSEIVER

NSX-SZ300

NSX-SZ309

NSX-SZ329 CX-NSZ329

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”

of NSX-SZ300 <HS,HT>, (S/M Code No. 09-012-440-5T3) and
NSX-SZ309 <HA>/SZ329 <LH>, (S/M Code No. 09-012-440-5T4).

CX-NSZ300

CX-NSZ309

TAPE

MECHANISM

ZZM-3 PR1NM

ZZM-3 YPR1NM

BASIC TAPE MECHANISM : ZZM-3
BASIC CD MECHANISM : BZG-5

CD

MECHANISM

BZG-5 ZD3NM

BZG-5 YZD3NCM

BZG-5 YZD3NM

SPEAKERSYSTEM

SX-NSZ302

SX-NSZ329

REMOTE

CONTROLLER

RC-ZAS02

• If requiring information about the CD mechanism, see Service Manual of
BZG-5 ZD3NM / YZD3NM, (S/M Code No. 09-00C-353-3N2) and
BZG-5 YZD3NCM, (S/M Code No. 09-00C-353-3N4).

S/M Code No. 09-014-440-5R2

REVISION

DATA

SPECIFICATIONS

Main unit CX-NSZ300 / CX-NSZ309 / CX-NSZ329

<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)

<AM/MW tuner section>
Tuning range HS, HT:

531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
HA, LH:
530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)

Usable sensitivity 350 µV/m
Antenna Loop antenna

<SW tuner section><HT>
Tuning range 5.730 MHz to 17.900 MHz
Usable sensitivity 40 µV/m (IEC)
Antenna Wire antenna

<Amplifier section>
Power output Rated

HS, HT: 32 W + 32 W
(6 ohms, THD 1 %, 1 kHz)
HA, LH: 62 W + 62 W
(6 ohms, THD 1 %, 1 kHz)
Reference
HS, HT: 40 W + 40 W
(6 ohms, THD 10 %,1 kHz)
HA, LH: 80 W + 80 W
(6 ohms, THD 10 %,1 kHz)

Total harmonic distortion HS, HT: 0.08 % (20 W, 1 kHz, 6 ohms,

DIN AUDIO)
HA, LH: 0.08 % (40 W, 1 kHz, 6 ohms,
DIN AUDIO

Inputs VIDEO/AUX: 500 mV

MIC: 1.0 mV (10 kohms) <HS, HT>

Outputs SPEAKERS: 6 ohms or more

PHONES: 32 ohms or more

<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 15 kHz
Recording system AC bias
Heads Deck 1: Playback x 1

Deck 2: Recording/Playback x 1,

erase x 1

<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)

<General>
Power requirements HA, HT, LH: 120 V/220-230 V/240 V AC

(switchable), 50/60 Hz
HS: AC 220 V, 60 Hz

Power consumption HS, HT: 70 W

HA, LH: 90 W
Power consumption With ECO mode on: 0.6 W
in standby mode With ECO mode off:

HS, HT: 14 W

HA, LH: 19 W

Dimensions (W x H x D) 260 x 324 x 351 mm
Weight of main unit HS, HT: 6.0 kg

HA, LH: 6.9 kg

Front speakers SX-NSZ302 / SX-NSZ329

Speaker system 3 way, bass reflex (magnetic

shielded type)
Speaker units Woofer: 160 mm cone

Tweeter: 60 mm cone

Super tweeter: 20 mm ceramic

Impedance 6 ohms
Dimensions (W x H x D) 230 x 324 x 235 mm
Weight HS, HT: 3.8 kg

HA, LH: 4.5 kg

• Design and specifications are subject to change without notice.

• The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.

Under license from BBE Sound,Inc.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJEC­TIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when

open and interlocks defeated avoid
exposure to beam.

s Advarsel: Usynlig laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of proce­dures other than those specified herin may result in
hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in
the right figure.

(KSS – 213F)

PICKUP Assy PWB

Solder

– 3 –

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

11

1 Remove the AC power cord.

11
22

2 Connect a discharging resistor at an end of lead wire that

22

has clips at both ends. Connect the other end of the lead
wire to metal chassis.

33

3 Contact the other end of the discharging resistor to the

33

positive (+) side (+VH) of C101. (For two seconds)

44

4 Contact the same end of the discharging resistor as step

44

33

3 to the negative (-) side (-VH) of C102 in the same way.

33

(For two seconds)

55

5 Check that voltage across C101 and C102 has decreased

55

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

Fig-1

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

11

1 Turn on the AC main power.

11
22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22
33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

33

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.

11

1 Remove the AC power cord.

11

FRONT C.B

18

MICROCOMPUTER

FRONT C.B

22

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22
33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

33

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

15

C113

Short with tweezers.

Fig-2-2

C113

%

*

VSS

VDD

MICRO­COMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

ELECTRICAL MAIN PARTS LIST

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

IC

87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-893-040 C-IC,NJM14558V-TE2
87-A21-695-010 IC,LA1845L
87-A21-928-010 IC,LC72131D-N
87-A21-218-110 IC,NJL64H380A

87-A21-401-040 C-IC,M61503FP
8B-NF9-601-030 C-IC,UPD780226GF-021-3BA
87-A21-269-010 IC,EW732

TRANSISTOR

87-A30-559-010 TR,CSB1370EF
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-107-070 C-TR,CMBT5401
87-A30-615-080 TR,STC250

87-A30-484-080 C-TR,KRA102S
87-026-610-080 TR,KTC3198GR
87-A30-190-080 TR,CC5551
87-A30-106-040 C-TR,CMBT5551
87-A30-162-010 FET,2SK2937

87-A30-091-080 FET,2SJ460
87-A30-090-080 FET,2SK2541
87-A30-062-080 C-TR,KRC104S
87-A30-495-080 TR,2SA1981Y
87-A30-234-080 TR,CSC4115BC

89-327-143-080 C-TR,2SC2714(O)
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
87-A30-086-040 C-TR,CSD1306E<HT>
87-A30-494-080 TR,2SA1980G

87-A30-528-010 TR,2SB1686
87-A30-529-010 TR,2SD2642
87-A30-087-080 C-FET,2SK2158
87-A30-074-080 C-TR,RT1P141C
87-A30-582-080 TR,CDA1585BC

87-A30-468-080 C-TR,KRC102S-RTK
87-A30-490-080 C-TR,KRC107S<HS>
87-A30-288-040 C-TR,DTC114YKA<EXCEPT HS>

DIODE

87-A40-393-090 DIODE,1N5402GW(F20)
87-A40-553-080 DIODE,1N4003 LES
87-A40-776-080 ZENER,UZ27BSD
87-A40-764-080 ZENER,UZ10BSC
87-A40-270-080 C-DIODE,MC2838

87-A40-269-080 C-DIODE,MC2836
87-A40-291-080 DIODE,1N4148M(CPT)
87-A40-749-080 ZENER,UZ5.6BSB
87-017-149-080 ZENER,HZS6A2L
87-A40-747-080 ZENER,UZ5.1BSB

87-A40-739-080 ZENER,UZ2.7BSA
87-A40-748-080 ZENER,UZ5.6BSA
87-A40-454-090 DIODE,1N5393 GW 12.5<HS,HT>
87-A40-455-090 DIODE,RL203 GW<HA,LH>

MAIN C.B

C3 87-012-368-080 C-CAP,S 0.1-50 Z F
C4 87-012-368-080 C-CAP,S 0.1-50 Z F
C5 87-012-368-080 C-CAP,S 0.1-50 Z F
C6 87-012-368-080 C-CAP,S 0.1-50 Z F
C9 87-010-759-080 C-CAP,U 0.1-25 Z F

C10 87-010-759-080 C-CAP,U 0.1-25 Z F
C11 87-010-759-080 C-CAP,U 0.1-25 Z F
C12 87-010-759-080 C-CAP,U 0.1-25 Z F
C19 87-A12-776-090 CAP, E 2200-50 M 85 SKR<HS,HT>
C19 87-A12-036-000 CAP, E 2200-63 M SMG<HA,LH>

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C20 87-A12-776-090 CAP, E 2200-50 M 85 SKR<HS,HT>
C20 87-A12-036-000 CAP, E 2200-63 M SMG<HA,LH>
C21 87-A12-777-090 CAP, E 3300-25 M 85 SKR
C22 87-A12-777-090 CAP, E 3300-25 M 85 SKR
C25 87-A12-072-080 CAP, E 100-25 SMG

C26 87-A12-072-080 CAP, E 100-25 SMG
C27 87-A12-072-080 CAP, E 100-25 SMG
C28 87-A12-072-080 CAP, E 100-25 SMG
C30 87-A12-095-080 CAP, E 100-50 SMG
C31 87-A12-062-080 CAP,E 100-10 SMG

C32 87-012-286-080 C-CAP, U 0.01-25
C34 87-A12-072-080 CAP, E 100-25 SMG
C35 87-A12-071-080 CAP, E 47-25 SMG
C36 87-A12-067-080 CAP, E 330-16 SMG
C38 87-012-286-080 C-CAP, U 0.01-25

C60 87-A12-089-080 CAP,E 3.3-50 SMG
C61 87-A12-071-080 CAP,E 47-25 SMG
C83 87-A12-068-080 CAP, E 470-16 SMG<HS>
C83 87-A12-074-080 CAP, E 470-25 SMG<EXCEPT HS>
C97 87-010-831-080 C-CAP,U 0.1-16 Z F

C101 87-012-278-080 C-CAP,U 2200P-50 K B<HS,HT>
C101 87-012-279-080 C-CAP,U 2700P-50 B<HA,LH>
C102 87-012-278-080 C-CAP,U 2200P-50 K B<HS,HT>
C102 87-012-279-080 C-CAP,U 2700P-50 B<HA,LH>
C103 87-A12-084-080 CAP,E 0.022-50 SMG

C104 87-A12-084-080 CAP,E 0.022-50 SMG
C105 87-012-277-080 C-CAP,U 1800P-50 K B GRM<HS,HT>
C106 87-012-277-080 C-CAP,U 1800P-50 K B GRM<HS,HT>
C107 87-A12-089-080 CAP,E 3.3-50 SMG
C108 87-A12-089-080 CAP,E 3.3-50 SMG

C111 87-A12-077-080 CAP,E 33-35 SMG
C112 87-A12-077-080 CAP,E 33-35 SMG
C113 87-012-195-080 C-CAP,U 100P-50 CH<HS,HT>
C113 87-A10-596-080 C-CAP,S 100P-100 J CH<HA,LH>
C114 87-012-195-080 C-CAP,U 100P-50 CH<HS,HT>

C114 87-A10-596-080 C-CAP,S 100P-100 J CH<HA,LH>
C117 87-A12-368-080 C-CAP,S 0.1-50 Z F
C118 87-A12-368-080 C-CAP,S 0.1-50 Z F
C119 87-012-286-080 C-CAP,U 0.01-25
C120 87-012-286-080 C-CAP,U 0.01-25

C123 87-010-177-080 C-CAP,S 820P-25 J SL C2012
C124 87-010-177-080 C-CAP,S 820P-25 J SL C2012
C133 87-012-282-080 C-CAP,U 4700P-50
C140 87-012-278-080 C-CAP,U 2200P-50
C186 87-010-759-080 C-CAP,U, 0.1-25F

C187 87-A12-091-080 CAP,E 10-50 SMG<HS,HT>
C187 87-010-866-080 CAP,E 10-63 M VX<HA,LH>
C188 87-A12-091-080 CAP,E 10-50 SMG<HS,HT>
C188 87-010-866-080 CAP,E 10-63 M VX<HA,LH>
C225 87-012-368-080 C-CAP,S 0.1-50 Z F

C226 87-012-368-080 C-CAP,S 0.1-50 Z F
C227 87-012-368-080 C-CAP,S 0.1-50 Z F
C228 87-012-368-080 C-CAP,S 0.1-50 Z F
C241 87-010-831-080 C-CAP,U 0.1-16 Z F
C301 87-012-275-080 C-CAP,U 1200P-50 K B GRM

C302 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C303 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C304 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C307 87-A12-062-080 CAP,E 100-10 SMG
C308 87-A12-062-080 CAP,E 100-10 SMG

C309 87-012-188-080 C-CAP,U 47P-50 J CH
C310 87-012-188-080 C-CAP,U 47P-50 J CH
C313 87-012-284-080 CAP, U 6800P-50
C314 87-012-284-080 CAP, U 6800P-50
C315 87-A12-062-080 CAP,E 100-10 SMG

C317 87-A12-085-080 CAP,E 0.33-50 SMG
C318 87-A12-085-080 CAP,E 0.33-50 SMG
C326 87-010-787-080 C-CAP,U 0.022-25 K B
C327 87-010-831-080 C-CAP,U 0.1-16 Z F
C360 87-A12-087-080 CAP,E 1-50 SMG

– 6 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C399 87-A10-039-080 C-CAP, U 470P-50 J CH
C401 87-A12-083-080 CAP,E 0.1-50 SMG
C402 87-A12-083-080 CAP,E 0.1-50 SMG
C403 87-012-193-080 C-CAP,U 82P-50 CH
C404 87-012-193-080 C-CAP,U 82P-50 CH

C405 87-012-286-080 CAP, U 0.01-25
C406 87-012-286-080 CAP, U 0.01-25
C407 87-012-286-080 CAP, U 0.01-25
C408 87-012-286-080 CAP, U 0.01-25
C409 87-012-278-080 C-CAP,U 2200P-50 B

C410 87-012-278-080 C-CAP,U 2200P-50 B
C411 87-A12-091-080 CAP,E 10-50 SMG
C412 87-A12-091-080 CAP,E 10-50 SMG
C452 87-A12-069-080 CAP,E 22-25 SMG
C453 87-012-279-080 C-CAP,U 2700P-50 B

C454 87-012-279-080 C-CAP,U 2700P-50 B
C455 87-012-279-080 C-CAP,U 2700P-50 B
C456 87-012-286-080 CAP, U 0.01-25
C457 87-A12-361-080 CAP,M 5600P-100 J CP
C458 87-012-274-080 CHIP CAP,U 1000P-50B

C459 87-012-271-080 CAP, U 560P-50
C460 87-010-831-080 C-CAP,U 0.1-16 Z F
C461 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C462 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C470 87-018-127-080 CAP, CER 470P-50V

C605 87-012-280-080 C-CAP,U 3300P-50 K B
C606 87-012-280-080 C-CAP,U 3300P-50 K B
C609 87-010-785-080 C-CAP,U 0.015-25 K B GRM
C610 87-010-785-080 C-CAP,U 0.015-25 K B GRM
C611 87-A12-084-080 CAP,E 0.22-50 SMG

C612 87-A12-084-080 CAP,E 0.22-50 SMG
C613 87-A12-084-080 CAP,E 0.22-50 SMG
C614 87-A12-084-080 CAP,E 0.22-50 SMG
C615 87-012-172-080 CAPACITOR CHIP U 10P CH
C616 87-016-459-080 CAP,E 470-10 M SMG

C617 87-016-459-080 CAP,E 470-10 M SMG
C618 87-A12-091-080 CAP,E 10-50 SMG
C620 87-010-263-080 CAP,E 100-10 M 11L SME
C623 87-A12-372-080 CAP,M 0.047-100 JP<HS,HT>
C623 87-A12-084-080 CAP,E 0.22-50 SMG<HA,LH>

C624 87-A12-372-080 CAP,M 0.047-100 JP<HS,HT>
C624 87-A12-084-080 CAP,E 0.22-50 SMG<HA,LH>
C630 87-016-669-080 C-CAP,S 0.1-25 K B
C631 87-012-281-080 C-CAP,U 3900P-50 K B GRM
C632 87-012-281-080 C-CAP,U 3900P-50 K B GRM

C633 87-A11-070-080 C-CAP,U 0.033-16 K B
C634 87-A11-070-080 C-CAP,U 0.033-16 K B
C661 87-012-336-080 C-CAP,U 330P-50 J SL
C662 87-012-336-080 C-CAP,U 330P-50 J SL
C671 87-010-831-080 C-CAP,U 0.1-16 Z F<HS,HT>

C672 87-010-831-080 C-CAP,U 0.1-16 Z F<HS,HT>
C673 87-012-278-080 C-CAP,U 2200P-50 K B<HS,HT>
C677 87-012-286-080 CAP, U 0.01-25
C771 87-A12-062-080 CAP,E 100-10 SMG
C772 87-012-286-080 CAP, U 0.01-25

C782 87-012-286-080 CAP, U 0.01-25
C783 87-012-286-080 CAP, U 0.01-25
C784 87-012-286-080 CAP, U 0.01-25
C785 87-012-286-080 CAP, U 0.01-25
C786 87-012-286-080 CAP, U 0.01-25

C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-A12-052-080 C-CAP,S 0.033-25 J B<EXCEPT HT>
C789 87-016-118-080 C-CAP,U 0.022-25 J B GRM<HT>
C790 87-A12-052-080 C-CAP,S 0.033-25 J B<EXCEPT HT>
C790 87-016-118-080 C-CAP,U 0.022-25 J B GRM<HT>

C791 87-010-831-080 C-CAP,U,0.1-16F
C792 87-012-286-080 CAP, U 0.01-25
C793 87-A12-090-080 CAP,E 4.7-50 SMG
C795 87-012-286-080 CAP, U 0.01-25
C796 87-012-286-080 CAP, U 0.01-25

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C797 87-A12-091-080 CAP,E 10-50 SMG
C798 87-012-286-080 CAP, U 0.01-25
C799 87-010-265-080 CAP,E 33-16 M 11L SME
C800 87-010-829-080 CAP, U 0.047-16
C801 87-A12-089-080 CAP,E 3.3-50 SMG

C802 87-010-829-080 CAP, U 0.047-16
C803 87-010-787-080 CAP, U 0.022-25 K B
C804 87-A12-062-080 CAP,E 100-10 SMG
C807 87-A12-086-080 CAP,E 0.47-50 SMG
C808 87-A12-087-080 CAP,E 1-50 SMG

C809 87-A12-087-080 CAP,E 1-50 SMG
C810 87-010-831-080 C-CAP,U,0.1-16F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-A12-086-080 CAP,E 0.47-50 SMG
C816 87-A12-086-080 CAP,E 0.47-50 SMG

C821 87-A12-091-080 CAP,E 10-50 SMG
C823 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C824 87-A12-090-080 CAP,E 4.7-50 SMG
C825 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C842 87-012-286-080 CAP, U 0.01-25

C844 87-012-286-080 CAP, U 0.01-25
C850 87-A12-071-080 CAP,E 47-25 SMG
C851 87-012-286-080 CAP, U 0.01-25
C852 87-012-286-080 CAP, U 0.01-25
C853 87-012-286-080 CAP, U 0.01-25

C858 87-010-831-080 C-CAP,U 0.1-16 Z F
C901 87-018-145-080 CAP,TC-U 6.8P-50 CH
C904 87-012-286-080 C-CAP,U 0.01-25
C905 87-012-286-080 C-CAP,U 0.01-25
C907 87-012-286-080 C-CAP,U 0.01-25

C908 87-A10-915-080 C-CAP,U 1000P-25 J CH
C909 87-012-286-080 C-CAP,U 0.01-25
C910 87-012-174-080 C-CAP,U 12P-50 J CH
C911 87-012-170-080 C-CAP,U 8P-50 CH
C912 87-012-195-080 C-CAP,U 100P-50CH

C913 87-012-286-080 C-CAP,U 0.01-25
C914 87-012-166-080 C-CAP,U 4P-50 C CH
C915 87-012-174-080 C-CAP,U 12P-50 J CH
C916 87-012-180-080 C-CAP,U 22P-50 CH
C917 87-012-186-080 C-CAP,U 39P-50 CH

C918 87-A10-039-080 C-CAP,U 470P-50 J CH
C921 87-012-195-080 C-CAP,U 100P-50CH
C922 87-012-174-080 C-CAP,U 12P-50 J CH CHJ
C940 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C941 87-012-180-080 C-CAP,U 22P-50 J CH<HT>

C943 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C945 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C946 87-010-971-080 C-CAP,S 4700P-50 J B<HT>
C947 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C948 87-012-166-080 C-CAP,U 4P-50 C CH<HT>

C952 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C953 87-012-286-080 C-CAP,U 0.01-25 K B<HT>
C954 87-A12-086-080 CAP,E 0.47-50 SMG<HT>
C956 87-A12-062-080 CAP,E 100-10 SMG<HT>
C959 87-010-831-080 C-CAP,U,0.1-16F

C960 87-010-831-080 C-CAP,U,0.1-16F<EXCEPT HT>
C961 87-012-167-080 C-CAP,U 5P-50 CH<EXCEPT HT>
C962 87-A12-087-080 CAP,E 1-50 SMG<HT>
C963 87-015-785-080 CHIP CAPACITOR, 0.1-25 Z F
C964 87-010-854-080 C-CAP,S 560P-50 J CH<HT>

C971 87-A12-067-080 CAP,E 330-16 SMG
C972 87-A12-090-080 CAP,E 4.7-50 SMG
C973 87-012-286-080 CAP, U 0.01-25
C974 87-012-286-080 CAP, U 0.01-25
C979 87-012-195-080 C-CAP,U 100P-50CH

C981 87-A12-071-080 CAP,E 47-25 SMG
C982 87-010-831-080 C-CAP,U,0.1-16F
C983 87-012-286-080 CAP, U 0.01-25 K B
C984 87-012-286-080 CAP, U 0.01-25 K B
C987 87-012-286-080 CAP, U 0.01-25 K B

– 7 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C989 87-012-286-080 C-CAP, U 0.01-25 K B<HT>
C991 87-012-176-080 C-CAP,U 15P-50 J CH
C992 87-012-176-080 C-CAP,U 15P-50 J CH
C993 87-012-274-080 CHIP CAP,U 1000P-50B
C995 87-012-274-080 CHIP CAP,U 1000P-50B

C997 87-010-831-080 C-CAP,U,0.1-16F
C998 87-A12-071-080 CAP,E 47-25 SMG
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER, SFE10.7MA5-A
CF832 87-008-261-010 FILTER, SFE10.7MA5-A

CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-A60-131-010 CONN,6P V FE
CNA001 8A-NF8-653-010 CONN ASSY,9P TID-A(480)

D902 87-A40-128-080 C-VARI-CAP,HVU202A
D903 87-A40-128-080 C-VARI-CAP,HVU202A
D951 87-A40-618-080 VARI-CAP,SVC 348(S/T)<HT>
FC602 88-906-251-110 FF-CABLE, 6P 1.25
J201 87-A60-488-010 JACK,DIA 6.3BLK ST W/SW

J203 87-A60-238-010 TERMINAL,SP 4P (MSC)
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
J940 87-A60-633-010 CONN,2P H 2.55MM JMT<HT>
JR123 87-012-195-080 C-CAP,U 100P-50 J CH<HS,HT>

JR123 87-A10-596-080 C-CAP,S 100P-100 J CH<HA,LH>
JR124 87-012-195-080 C-CAP,U 100P-50 J CH<HS,HT>
JR124 87-A10-596-080 C-CAP,S 100P-100 J CH<HA,LH>
L201 87-A50-610-010 COIL,1UH K(MDEC)
L202 87-A50-610-010 COIL,1UH K(MDEC)

L451 87-007-342-010 COIL,OSC 85KHZ BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-552-010 FLTR,CFMT-450AL(TOK)<HT>
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)<EXCEPT HT>
L811 87-005-847-080 COIL,2.2UH CECS

L832 87-005-847-080 COIL,2.2UH CECS
L902 88-ZA1-602-110 COIL,FM-RF-U2 2G
L903 88-ZA1-601-010 COIL,FM-RF-U1 2G
L904 87-005-847-080 COIL,2.2UH(CECS)
L905 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS)

L906 88-ZA1-603-010 COIL,FM-OSC-U 2G
L941 87-A50-022-010 COIL,ANT SW (COI) 7.96MHZ<HT>
L942 87-A50-550-010 COIL,OSC SW-2N (COI)<HT>
L943 87-A50-522-080 COIL,1MH K CEC<HT>
L944 87-A50-159-010 COIL,10MH K C2B<HT>

L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<EXCEPT HT>
L952 87-A50-430-010 COIL,ANT MW(3BSW)<HT>
L953 87-A50-431-010 COIL,OSC MW(3BSW)<HT>
R129 87-A00-258-080 RES,M/F 0.22-1W J<HS,HT>
R129 87-A00-262-080 RES,M/F 0.15-2W J<HA,LH>

R130 87-A00-258-080 RES,M/F 0.22-1W J<HS,HT>
R130 87-A00-262-080 RES,M/F 0.15-2W J<HA,LH>
R131 87-A00-258-080 RES,M/F 0.22-1W J<HS,HT>
R131 87-A00-262-080 RES,M/F 0.15-2W J<HA,LH>
R132 87-A00-258-080 RES,M/F 0.22-1W J<HS,HT>

R132 87-A00-262-080 RES,M/F 0.15-2W J<HA,LH>
R243 87-A00-999-050 RES,180-1/2W J BLT2J<HS,HT>
R243 87-A01-001-050 RES,220-1/2W J BLT2J<HA,LH>
R244 87-A00-999-050 RES,180-1/2W J BLT2J<HS,HT>
R244 87-A01-001-050 RES,220-1/2W J BLT2J<HA,LH>

R245 87-A00-999-050 RES,180-1/2W J BLT2J<HS,HT>
R245 87-A01-002-050 RES,270-1/2W J BLT2J<HA,LH>
R246 87-A00-999-050 RES,180-1/2W J BLT2J<HS,HT>
R246 87-A01-002-050 RES,270-1/2W J BLT2J<HA,LH>
R790 87-012-286-080 C-CAP, U 0.01-25 K B

R991 87-012-195-080 C-CAP,U 100P-50CH
R993 87-012-195-080 C-CAP,U 100P-50CH
R995 87-012-195-080 C-CAP,U 100P-50CH
SFR451 87-024-435-080 SFR,33K H RH063MC
SFR452 87-024-435-080 SFR,33K H RH063MC

DESCRIPTIONREF. NO. KANRI

TC941 87-A91-773-080 TRIMMER,PLY 20P 6.8X5.4 CDYL<HT>
TC943 87-A91-774-080 TRIMMER,PLY 30P 6.8X5.4 CDYL<HT>
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P

X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

FRONT C.B

C108 87-010-785-080 C-CAP,U 0.015-25 K B GRM
C153 87-010-787-080 C-CAP,U 0.022-25 K B
C154 87-A12-078-040 CAP,E 47-35 SMG
C155 87-010-404-040 CAP,E 4.7-50 M 11L SME
C156 87-010-404-040 CAP,E 4.7-50 M 11L SME

C301 87-012-278-080 C-CAP,U 2200P-50 K B
C351 87-A10-353-080 C-CAP,U 0.22-10 K B
C361 87-012-274-080 C-CAP,U 1000P-50 K B
C362 87-012-274-080 C-CAP,U 1000P-50 K B
C371 87-012-274-080 C-CAP,U 1000P-50 K B

C372 87-012-274-080 C-CAP,U 1000P-50 K B
C401 87-012-282-080 C-CAP,U 4700P-50 K B<HS,HT>
C402 87-010-112-040 CAP,E 100-16 M 11L SME<HS,HT>
C403 87-010-545-040 CAP,E 0.22-50 M 11L SME<HS,HT>
C404 87-012-191-080 C-CAP,U 68P-50 J CH<HS,HT>

C405 87-010-545-040 CAP,E 0.22-50 M 11L SME<HS,HT>
C406 87-010-545-040 CAP,E 0.22-50 M 11L SME<HS,HT>
C407 87-010-405-040 CAP,E 10-50 M 11L SME<HS,HT>
C408 87-012-195-080 C-CAP,U 100P-50 J CH<HS,HT>
C409 87-010-265-040 CAP,E 33-16 M 11L SME<HS,HT>

C410 87-010-829-080 C-CAP,U 0.047-16 Z F<HS,HT>
C413 87-A10-978-080 C-CAP,U 820P-25 J CH<HS,HT>
C601 87-010-382-040 CAP,E 22-25 SME
C801 87-A10-804-080 C-CAP,S 0.1-25 J B
C802 87-010-316-080 C-CAP,S 33P-50 J CH GRM

C803 87-012-280-080 C-CAP,U 3300P-50 K B
C804 87-A10-592-080 C-CAP,S 0.015-50 J B
C805 87-012-184-080 C-CAP,U 33P-50 J CH
C806 87-012-274-080 C-CAP,U 1000P-50 K B
C807 87-012-274-080 C-CAP,U 1000P-50 K B

C808 87-010-544-040 CAP,E 0.1-50 M 11L SME
C809 87-010-404-040 CAP,E 4.7-50 SME
C810 87-012-286-080 C-CAP,U 0.01-25 K B
C811 87-A12-052-080 C-CAP,S 0.033-25 J B
C901 87-012-195-080 C-CAP,U 100P-50 CH

C902 87-012-195-080 C-CAP,U 100P-50 CH
C903 87-012-195-080 C-CAP,U 100P-50 CH
C904 87-012-195-080 C-CAP,U 100P-50 CH
C905 87-012-195-080 C-CAP,U 100P-50 CH
C906 87-012-195-080 C-CAP,U 100P-50 CH

C907 87-012-195-080 C-CAP,U 100P-50 CH
C908 87-012-195-080 C-CAP,U 100P-50 CH
C909 87-012-195-080 C-CAP,U 100P-50 CH
C910 87-012-195-080 C-CAP,U 100P-50 CH
C911 87-012-274-080 C-CAP,U 1000P-50 K B

C912 87-010-831-080 C-CAP,U 0.1-16 Z F
C913 87-A10-189-040 CAP,E 220-10 M 5L
C914 87-A10-189-040 CAP,E 220-10 M 5L
C915 87-010-831-080 C-CAP,U 0.1-16 Z F
C916 87-010-831-080 C-CAP,U 0.1-16 Z F

C917 87-010-831-080 C-CAP,U 0.1-16 Z F
C919 87-012-286-080 C-CAP,U 0.01-25 K B
C920 87-010-829-080 C-CAP,U 0.047-16 Z F
C921 87-012-282-080 C-CAP,U 4700P-50 K B
C951 87-012-172-080 C-CAP,U 10P-50 D CH

C952 87-010-854-080 C-CAP,S 560P-50 J CH
C953 87-012-349-080 C-CAP,S 1000P-50 J CH GRM
C961 87-010-378-040 CAP,E 10-16 M 11L SME
C962 87-012-336-080 C-CAP,U 330P-50 J SL
C963 87-010-831-080 C-CAP,U 0.1-16 Z F

PART NO.

NO.

– 8 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

CN104 87-A60-057-010 CONN,11P V 9604S-11C
CN701 87-099-720-010 CONN,30P BLK TYK-B(P)
CN731 87-099-196-010 CONN,8P V BLK 6216
EMI401 87-008-372-080 FLTR,EMI BL01 RN1<HS,HT>
FC104 88-911-101-110 FF-CABLE,11P 1.25

FC731 88-908-301-110 FF-CABLE,8P 1.25
FL901 8B-NF9-605-010 FL,BJ814GNK
J401 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC<HS,HT>
L951 87-A50-655-010 COIL,CLK 4.19M (TOKO)7KLY
LED209 87-A41-062-040 LED,LTL-1CHEE-012A RED

S321 87-A90-164-080 SW,TACT SKQNAB(N)
S322 87-A90-164-080 SW,TACT SKQNAB(N)
S323 87-A90-164-080 SW,TACT SKQNAB(N)
S324 87-A90-164-080 SW,TACT SKQNAB(N)
S325 87-A90-164-080 SW,TACT SKQNAB(N)

S326 87-A90-164-080 SW,TACT SKQNAB(N)
S327 87-A90-095-080 SW,TACT EVQ11G04M
S328 87-A90-095-080 SW,TACT EVQ11G04M
S329 87-A90-095-080 SW,TACT EVQ11G04M
S330 87-A90-164-080 SW,TACT SKQNAB(N)

S331 87-A90-164-080 SW,TACT SKQNAB(N)
S332 87-A90-164-080 SW,TACT SKQNAB(N)
S333 87-A90-164-080 SW,TACT SKQNAB(N)
S334 87-A90-164-080 SW,TACT SKQNAB(N)
S341 87-A90-164-080 SW,TACT SKQNAB(N)

S342 87-A90-164-080 SW,TACT SKQNAB(N)
S343 87-A90-164-080 SW,TACT SKQNAB(N)
S344 87-A90-164-080 SW,TACT SKQNAB(N)
S345 87-A90-164-080 SW,TACT SKQNAB(N)
S346 87-A90-164-080 SW,TACT SKQNAB(N)

DESCRIPTIONREF. NO. KANRI

S347 87-A90-164-080 SW,TACT SKQNAB(N)
S348 87-A90-164-080 SW,TACT SKQNAB(N)
S349 87-A90-164-080 SW,TACT SKQNAB(N)
S361 87-A92-041-010 SW,RTRY XRE012103PVB30F-24
S371 87-A92-040-010 SW,RTRY XRE012103PVB30F-12

VR401 86-NFA-607-010 VR,RTRY 10K15AX1 1 V XV0121PVN<HS,HT>

PT C.B

CN1 87-A61-110-010 CONN,9P V TID-A

!

PT1 8B-NF9-613-010 PT, BNF-9 HR<HS,HT>

!

PT1 8B-NF9-615-010 PT, BNF-9 LH<HA,LH>

!

PT2 8B-MA6-673-010 PT,SUB BMA H (VRK)

!

RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2

!

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<EXCEPT HS>

!

T1 87-A60-317-010 TERMINAL, 1P MSC

!

T2 87-A60-317-010 TERMINAL, 1P MSC

DECK C.B

CN1 87-099-753-010 CONN,11P 9604
SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY, 27
SOL2 82-ZM1-618-410 SOL ASSY, 27
SW1 87-A90-673-010 SW,MICRO ESE11SH1C

SW2 87-A91-500-010 SW,MICRO MPU11470MLB0
SW3 87-A91-500-010 SW,MICRO MPU11470MLB0
SW4 87-A91-500-010 SW,MICRO MPU11470MLB0
SW5 87-A90-673-010 SW,MICRO ESE11SH1C

PART NO.

NO.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

A

Resistor Code

Chip resistor

Wattage Type Tolerance

1/16W 1005 5% CJ

1/16W

1/10W

1/8W

1608

2125

3216

5%

5%

5%

Symbol

CJ

CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108

118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45

2 1.25 0.45

3.2

1.6

: A
: A

– 9 –

TRANSISTOR ILLUSTRATION

E C B

CDA1585BC
KTC3198GR

S

D

G

2SK360E

E C B

2SA1980G
2SA1981Y
CC5551
STC250

S D G

2SK2541

B C E

CSB1370EF

D

G

S

2SK21582SJ460

E C B

CSC4115BC

B

E

2SA1235F
2SC2714(O)
2SC3052F
CMBT5401
CMBT5551
CSD1306E
DTC114YKA

C

KRA102S
KRA107S
KRC102S-RTK
KRC104S
KRC107S
RT1P141C

B C E

2SB1686
2SD2642

G D S

2SK2937

– 10 –

FL (BJ814GNK) GRID ASSIGNMENT AND ANODE CONNECTION

GRID ASSIGNMENT

 11 

ANODE CONNECTION

 12 