EAW MW12 User Manual

MicroWedge MW12 Specifications group · S
2-WAY FULL-RANGE STAGE MONITOR
See NOTES TABULAR DATA for details
CONFIGURATION
Subsystem
Transducer Loading
LF 1x 12 in cone Vented
HF 1x 1.4 in exit, 3 in voice Horn-loaded coil compression driver
Operating Mode
Amplifier Channels External Signal Processing
Single-amp LF/ HF High pass filter Bi-amp LF, HF DSP w/2-way filters
PERFORMANCE 1
Operating Range 64 Hz to 20 kHz Nominal Beamwidth (conical)
Horz 90° Vert 90° Axial Sensitivity (whole space SPL) LF/HF 94 dB 64 Hz to 20 kHz LF 95 dB 60 Hz to 930 Hz HF 106 dB 730 Hz to 20 kHz
Input Impedance (ohms)
FEATURES
• Highly coherent coaxial design (12-inch LF)
•Enhanced fidelity and power handling
•Upgraded transducers and crossover design
•Switchable single-amp/bi-amp modes
DESCRIPTION
The MicroWedge MW12 is a collaboration between original MicroWedge Series inventor Dave “Rat” Levine (owner of Rat Sound Systems, Inc.) and the EAW Engineering Department, resulting in dramatically upgraded performance and ergonomics. A 12-inch woofer is paired with a 3-inch voice coil HF compression driver on a horn that provides full yet controlled 90-degree horizontal dispersion. All frequencies emanate from the exact same point, eliminating crossover region problems and time/phase irregularities, as well as
PRELIMINARY
optimizing coherency. The coaxial approach also contributes to a very compact, low-profile footprint.
MicroWedge MW12 monitors are processor enhanced (rather than processor dependant) for true “plug and play” operation. User selectable single-amp and bi-amp modes are provided. The large port on the front of the cabinet enhances LF response in coupling with the floor, and this port houses both the carrying handle and the passive/active mode switch. The port also contains dual input connectors, keeping them concealed and protected, and allowing wedges to be placed as close together as desired. Additional cable can be stored in the port without impacting LF performance.
Rubber feet on the bottom of the enclosure reduce abrasion, and new integral rigging hardware – also mounted on the enclosure bottom – facilitates easy flying. The Baltic birch cabinets are protected with EAW’s RoadCoat™ finish that’s extremely durable, and the rugged steel grille keeps its distinctive shape even when stood upon. All components are highly liquid tolerant – virtually impervious to spilled drinks as well as natural elements like rain.
Nominal Minimum
LF/HF 8 6.4 @ 818 Hz LF 8 7.9 @ 231 Hz HF 8 8.7 @ 4732 Hz
High Pass Filter
High Pass =>50 Hz, 12 dB/octave Butterworth
Accelerated Life T est 2
LF/HF 69 V 600 W @ 8 ohm LF 69 V 600 W @ 8 ohm HF 35 V 150 W @ 8 ohm
Calculated Axial Output Limit (whole space SPL)
Average Peak
LF/HF 122 dB 128 dB LF 123 dB 129 dB HF 128 dB 134 dB
ORDERING DATA
Description Part Number
MW12 2-Way Full Range Loudspeaker Black 0011736-90
1 To achieve specified performance, the listed external signal processing with EA W -provided settings is required. 2 For recommendations to select power amplifier size refer to : “HOW MUCH AMPLIFIER POWER DO I NEED?” on the EA W web site.
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
MicroWedge MW12 Specifications group · S
NOTES:
1. SYMBOL INDICATES 15.00 X 1.35 FLY TRACK.
RIGHT SIDE
4X 6.33
R 644.67
R 44.44
DIMENSIONS APPLY
TO BOTH SIDES
50.86
27°
[304.8]
(13°)
[6.3]
[101.8]
HANDLE / PORT
LOGO PLATE
101.82
2X INPUT
FRONT
[333.9]
L
C
GRILLE
PARTIALLY
SHOWN
TOP
333.86
[325.8]
325.79
579.23
304.80
[579.2]
[438.6]
L
C
438.65
27°
139.86
[R664.7]
[139.9]
[216.7]
[63.0]
MW12
PROTOTYPE
[50.9]
LOUD Technologies Inc.
ONE MAIN STREET WHITINSVILLE, MA 01588 USA
BACK
300.83
417.69
MODEL/SERIAL
NUMBER PLATE
63.00
[417.7]
[44.4]
4X RUBBER
FEET
216.68
L
C
[300.8]
ENCLOSURE
Material Baltic birch plywood Finish RoadCoatTM wear resistant textured black paint Grille Powder-coated perforated steel
PRELIMINARY
NOTE: This drawing has been reduced. Do not scale.
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
MicroWedge MW12 Specifications group · S
MW 12 GRPH Master1
MW 12 GRPH Master1
MW 12 GRPH Master1
MW 12 GRPH Master1
MW12 POLAR Master1
PERFORMANCE DATA
See NOTES GRAPHIC DATA for details
Frequency Response: Processed Multi-amplified
LF = green, HF = black, Complete = blue
10
0
-10
-20
SPL (dB)
-30
-40
-50 10 100 1000 20000
Frequency (Hz)
Frequency Response: Unprocessed
LF = green, HF = black, Complete = blue
120
110
100
90
SPL (dB)
80
70
60
10 100 1000 20000
Frequency (Hz)
Impedance Magnitude
LF = green, HF = black, Complete = blue
PRELIMINARY
100
Frequency Response: Digital Signal Processor
LF = green, HF = black
20
10
0
-10
dB re 0.775 V
-20
-30
-40 10 100 1000 20000
Frequency (Hz)
Beamwidth (-6 dB SPL Points)
Horizontal = orange Vertical = black
360
100
10
Ohms
1
10 100 1000 20000
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
Frequency (Hz)
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
10
Degrees
1
100 1000 20000
Frequency (Hz)
MicroWedge MW12 Specifications group · S
0
-45
-90
-135
180
135
90
45
100 Hz
125 Hz
160 Hz
200 Hz
0
-45
-90
-135
180
135
90
45
250 Hz
315 Hz
400 Hz
500 Hz
0
-45
-90
-135
180
135
90
45
630 Hz
800 Hz
1000 Hz
1250 Hz
0
-45
-90
-135
180
135
90
45
1600 Hz
2000 Hz
2500 Hz
3150 Hz
0
-45
-90
-135
180
135
90
45
4000 Hz
5000 Hz
6300 Hz
8000 Hz
0
-45
-90
-135
180
135
90
45
10000 Hz
12500 Hz
16000 Hz
HORIZONTAL POLAR DATA (Gridlines: 6 dB axial / 15 degree radial)
See NOTES GRAPHIC DATA for details
PRELIMINARY
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
MicroWedge MW12 Specifications group · S
0
-45
-90
-135
180
135
90
45
100 Hz
125 Hz
160 Hz
200 Hz
0
-45
-90
-135
180
135
90
45
250 Hz
315 Hz
400 Hz
500 Hz
0
-45
-90
-135
180
135
90
45
630 Hz
800 Hz
1000 Hz
1250 Hz
0
-45
-90
-135
180
135
90
45
4000 Hz
5000 Hz
6300 Hz
8000 Hz
0
-45
-90
-135
180
135
90
45
10000 Hz
12500 Hz
16000 Hz
0
-45
-90
-135
180
135
90
45
1600 Hz
2000 Hz
2500 Hz
3150 Hz
VERTICAL POLAR DATA (Gridlines: 6 dB axial / 15 degree radial)
See NOTES GRAPHIC DATA for details
PRELIMINARY
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
MicroWedge MW12 Specifications group · S
INPUT PANEL
SIGNAL DIAGRAM
LEGEND
DSP: User-supplied Digital Signal Processor. HPF: High Pass Filter for crossover or Recommended High Pass Filter. LPF: Low Pass Filter for crossover. LF/MF/HF: Low Frequency / Mid Frequency / High Frequency. AMP: User-supplied Power Amplifier. XVR: Passive LPFs, HPFs, and EQ integral to the loudspeaker.
NOTES
TABULAR DATA
1. Measurement/Data Processing Systems: Primary - FChart: proprietary EAW software; Secondary - Brüel & Kjær 2012.
2. Microphone Systems: Earthworks M30; Brüel & Kjær 4133
3. Measurements: Dual channel FFT; length: 32 768 samples; sample rate: 48 kHz; logarithmic sine wave sweep.
4. Measurement System Qualification (includes all uncertainties): SPL: accuracy +/-0.2 dB @ 1 kHz, precision +/-0.5 dB 20 Hz to 20 kHz, resolution 0.05 dB; Frequency: accuracy +/-1 %,
precision +/-0.1 Hz, resolution the larger of 1.5 Hz or 1/48 octave; Time: accuracy +/-10.4 µs, precision +/-0.5 µs, resolution 10.4 µs; Angular: accuracy +/-1°, precision +/-0.5°, resolution 0.5°.
5. Environment: Measurements time-windowed and processed to eliminate room ef fects, approximating an anechoic environment. Data processed as anechoic or fractional space, as noted.
6. Measurement Distance: 7.46 m. Acoustic responses represent complex summation of the subsystems at 20 m. SPL is referenced to other distances using the Inverse Square Law.
7. Enclosure Orientation: For beamwidth and polar specifications, as shown in Mechanical Specification drawing.
8. Volts: Measured rms value of the test signal.
9. Watts: Per audio industry practice, “loudspeaker watts” are calculated as voltage squared divided by rated nominal impedance. Thus, these are not True Watt units of energy as defined
by International Standard.
10. SPL: (Sound Pressure Level) Equivalent to the average level of a signal referenced to 0 dB SPL = 20 microPascals.
11. Subsystem: This lists the transducer(s) and their acoustic loading for each passband. Sub = Subwoofer, LF = Low Frequency, MF = Mid Frequency, HF = High Frequency.
12. Operating Mode: User selectable configurations. Between system elements, a comma (,) = separate amplifier channels; a slash (/) = single amplifier channel. DSP = Digital Signal Processor.
IMPORTANT: To achieve the specified performance, the listed external signal processing must be used with EAW-provided settings.
13. Operating Range: Range where the processed Frequency Response stays within -10 dB SPL of the power averaged SPL within this range; measured on the geometric axis. Narrow band dips are excepted.
14. Nominal Beamwidth: Design angle for the -6 dB SPL points, referenced to 0 dB SPL as the highest level.
15. Axial Sensitivity: Power averaged SPL over the Operating Range with an input voltage that would produce 1 W at the nominal impedance; measured with no external processing on the
geometric axis, referenced to 1 m.
16. Nominal Impedance: Selected 4, 8, or 16 ohm resistance such that the minimum impedance point is no more than 20% below this resistance over the Operating Range.
17. Accelerated Life Test: Maximum test input voltage applied with an EIA-426B defined spectrum; measured with recommended signal processing and Recommended Protection Filter.
18. Calculated Axial Output Limit: Highest average and peak SPLs possible during the Accelerated Life Test. The Peak SPL represents the 2:1 (6 dB) crest factor of the Life Test signal.
19. High Pass Filter: This helps protect the loudspeaker from excessive input signal levels at frequencies below the Operating Range.
GRAPHIC DATA
1. Resolution: To remove insignificant fine details, 1/12 octave cepstral smoothing was applied to acoustic frequency responses and 1/3 octave cepstral smoothing was applied to the
beamwidth and impedance data. Other graphs are plotted using raw data.
2. Frequency Responses: Variation in acoustic output level with frequency for a constant input signal. Processed: normalized to 0 dB SPL. Unprocessed inputs: 2 V (4 ohm nominal impedance),
2.83 V (8 ohm nominal impedance), or 4 V (16 ohm nominal impedance) referenced to a distance of 1 m.
3. Processor Response: The variation in output level with frequency for a constant input signal of 0.775 V = 0 dB reference.
4. Beamwidth: Average angle for each 1/3 octave frequency band where, starting from the rear of the loudspeaker, the output first reaches -6 dB SPL referenced to 0 dB SPL as the highest
level. This method means the output may drop below -6 dB SPL within the beamwidth angle.
5. Impedance: Variation in impedance magnitude, in ohms, with frequency without regard to voltage/current phase. This means the impedance values may not be used to calculate True Watts (see 9 above).
6. Polar Data: Horizontal and vertical polar responses for each 1/3 octave frequency band 100 Hz to 16 kHz or Operating Range.
PRELIMINARY
Eastern Acoustic Works One Main Street Whitinsville, MA 01588 tel 800 992 5013 / 508 234 6158 fax 508 234 8251 www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. Part Number: 0011736-90 February 2008
Loading...