Page 1
A
C
O
U
S
T
I
C
A
L
P
E
R
F
O
R
M
A
N
C
E
P
A
R
T
N
E
R
S
H
I
P
TECHNICAL SPECIFICATIONS MQV1394
FEATURES
•Full Range VA4™ loudspeaker system
•Optimized for permanent install only
•Direct radiating 15-inch woofer in optimally vented
enclosure
•Horn loaded 10-inch cone with VA4™ phase plug
•2-inch exit/75mm voice coil compression driver on
constant directivity horn
DESCRIPTION
The MQV Series is part of the next generation of permanent
installation loudspeakers. Using VA4™ Technology developed
for the KF700 series, the MQV range replaces the ASV range
of virtual array systems.
The MQV1394 uses a single, direct radiating 15-inch woofer
in an optimally vented enclosure.
A single, horn loaded 10-inch midrange cone with a special
geometry is used which produces a time coherent wavefront
through the upper portion of the midrange that is critical to
vocal articulation. A phase plug with radial slots then serves
to reduce the mechanical resistance of the subsystem without affecting the directivity of the source, allowing flawless
vertical arraying of multiple MQV modules
A high power 2-inch exit/75mm voice coil compression driver
is mounted on a constant directivity horn for consistent,
accurate dispersal of HF information.
APPLICATIONS
The MQV1394 is engineered as a full range component for
very large format arrays and is an effective tool in largescale permanent installations. Comprehensive mounting
points allow for flexible installation.
Applications include:
Large Church Large Arenas
Stadiums
DESCRIPTIVE DATA
LF Subsystem 1x 15-in Woofer
MF Subsystem 1x 10-in Horn Loaded Cone
HF Subsystem 2-in Exit/75mm Voice Coil
Compression Driver on Constant
Directivity Horn
Configuration Three-way, Full Range
Powering Triamplified
Cabinet Type (shape) Trapezoid
Enclosure Materials Baltic Birch Plywood
Finish Wear-resistant Textured Black
Paint
Connectors 1x 6-Terminal Barrier Strip &
1x Neutrik NL8 Speakon
Suspension Hardware (16) 3/8”-16 Threaded Mounting
Points (4 each on top, bottom and
sides)
Grill Powder Coated Perforated Steel
Dimensions Inches Millimeters
Height (front) 26.65 677
Height (rear) 15.3 389
Width 56.25 1429
Depth 25.59 650
Trapezoid Angle 12.5 Degrees per Side
Weights Pounds Kilograms
Net Weight 215 97.5
Shipping Weight 240 108.9
EASTERN ACOUSTIC WORKS
One Main Street, Whitinsville, MA 01588 • (508) 234 - 6158 • FAX (508) 234 - 8251 • Email info@eaw.com • Web http://www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. • MQV1394 PUB#888170/2p/4/1/00 • Printed In USA
Page 2
A
C
O
U
S
T
I
C
A
L
P
E
R
F
O
R
M
A
N
C
E
P
A
R
T
N
E
R
S
H
I
P
TECHNICAL SPECIFICATIONS MQV1394
DIMENSIONAL DRAWING
INDICATES MOUNTING POINT,
MQV1394
56.25
26.65
GRILLE PARTIALLY SHOWN
FRONT
15.71
8.10
DIMENSIONS APPLY TO TOP
AND BOTTOM
509043 (A)
exp 3/29/00 dpm
C
L
TOP
16X 3/8-16 THREADED HOLE (PI ANGLE).
12.50
ACCESS
PANEL
WITH
INPUT
(1.95)52.35
C
L
19.55
25°
5.63
BACK
7.50
25.59
15.34
C
L
SIDES
DIMENSIONS APPLY TO
BOTH SIDES
NOMINAL DATA
Frequency Response
±3 dB 50 Hz to 16 kHz
-10 dB 34 Hz
Axial Sensitivity (dB SPL, 1 Watt @ 1m)
LF 97
MF 108
HF 110
Impedance (Ohms)
LF 8
MF 8
HF 8
Power Handling, AES Standard (Watts)
LF 550
MF 400
HF 200
Calculated Maximum Output (dB SPL @ 1m)
LF Peak 130.4
MF Peak 140.0
HF Peak 139.0
LF Long Term 124.4
MF Long Term 134.0
HF Long Term 133.0
Nominal Coverage Angle, -6 dB Points (degrees)
Horizontal 90
Vertical 45
Recommended High-Pass Frequency
24 dB/Octave 35Hz
ACCESS PANEL
7.37
(15.30)12.75
ARCHITECTURAL SPECIFICATIONS
The three-way full range loudspeaker system shall incorporate a 15-in woofer (vented), a 10-in cone MF transducer,
and a 2-in exit compression driver HF transducer.
The MF driver shall be loaded into a midrange horn constructed of 3mm birch plywood reinforced with high density
polyurethane foam. The MF horn shall incorporate a radial
phase plug. The HF driver shall be loaded on constant directivity horn with a nominal coverage pattern of 90° (h) x 45°
(v).
System frequency response shall vary no more than ±3 dB
from 50 Hz to 16 kHz measured on axis. The midrange frequency section shall produce a Sound Pressure Level (SPL) of
108 dB SPL on axis at 1 meter with a power input of 1 Watt,
and shall be capable of producing a peak output of 141 SPL
on axis at 1 meter. The high frequency section shall produce
a Sound Pressure Level (SPL) of 110 dB SPL on axis at 1
meter with a power input of 1 Watt, and shall be capable of
producing a peak output of 139 SPL on axis at 1 meter. The
midrange frequency section shall handle 400 Watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 Ohms. The high frequency section shall handle 200
Watts of amplifier power (AES Standard) and shall have a
nominal impedance of 8 Ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of 15mm thickness void-free cross-grainlaminated Baltic birch plywood and shall employ extensive
internal bracing. It shall be finished in wear-resistant textured black paint. Input connectors shall be 1x 6-terminal
barrier strip and one Neutrik NL8 Speakon. A total of sixteen
3/8"-16 threaded mounting points (4 each top, bottom and
sides) shall be provided. The front of the loudspeaker shall
be covered with a powder coated perforated steel grill.
The three-way full range loudspeaker shall be the EAW model
MQV1394.
Acoustic Performance Partnership Eastern Acoustic Works MQV1394
One Main Street, Whitinsville MA, 01588 USA • Phone 508/234-6158 • Toll Free 800/992-5013 • Fax 508/234-8251 • Web http://www.eaw.com • email info@eaw.com
Loading...