The new MQ Series r epresen ts the n ext g ener ation o f perm anent installation loudspeaker systems. Using VA4 Technology developed for the new KF700 Series, the MQ range replaces the MH and BV ranges of Virtual Array systems. The
Series comprises match ed sets of mid/high and low fr equency
enclosures that enjoy complementary dimensions and
trapeziod angles to facilitate the creation of optimizedcoverage arrays.
The MQ1394 uses a horn-loaded 10-in mi dran g e con e with a
specially designed geometry that produces a time-coherent
wavefront through the upper porti on of the mi dr ange that is
critical to vocal articulation. A phase plug with radial slots
then serves to reduce the mechanical reactance of the subsystem without affecting the directivity of the source, allowing for flawless arraying of multiple MQ mid/high
modules.
A high power 2-in exit/75mm voice coil hi gh frequency compression driver is m ounted on a constan t directivity horn f or
consistent, accurate dispersal o f HF information. The MQ1394
provides a nominal coverage pattern of 90° (h) x 40° (v).
APPLICATION
The MQ1394 mid/high m odule works with the MQ1312 triple
12-in low frequency module to create arrays for use in a
wide variety of permanently installed applications.
The most common array configuration is 2x MQ1394’s separated by a single MQ1312. Unlik e most oth er 90° horizontal
coverage array modules, the MQ1394 is designed to tight
pack with the MQ1312 to achieve optimal coverage. This
provides an excellent center channel array for large, fanshaped venues that use an L/C/R configuration.
All MQ Series enclosures feature a comprehensive system of
3/8”-16 threaded mounting points for maximum flexibility
when suspending arrays overhead.
Applications include:
Large House of Worship
Arena
Stadium
Theater
Performing Arts Center
One Main Street, Whitinsville MA, 01588 USA • Phone 508/234-6158 • Toll Free 800/992-5013 • Fax 508/234-8251 • Web http://www.eaw.com • email info@eaw.com
One Main Street, Whitinsville, MA 01588 • (508) 234 - 6158 • FAX (508) 234 - 8251 • Email info@eaw.com • Web http://www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. • PUB# MQ1394-888143/2 pp/4/15/99 • Printed In USA
M
R
A
N
O
F
C
R
E
E
P
P
A
L
A
C
I
T
S
U
O
C
A
R
T
N
E
R
S
H
I
P
TECHNICAL SPECIFICATIONSMQ1394
DIMENSIONAL DRAWINGS
MQ1394
40.00
GRILL PARTIALLY
6.3713.15
510836 (A)
exp 4/8/99 dpm
FRONT
36.10
1.95
CENTER OF BALANCE, TBD.
MOUNTING POINT, 3/8-16 THREADED HOLE.
32.00
SHOWN
SIDES
25.61
10.57
(8.12)
INPUT
C
L
12.16
23.28
50°
TOP
C
L
NOMINAL DATA
Frequency Response (1 W @ 1m)
±3 dB190 Hz to 19 kHz
-10 dB145 Hz
Axial Sensitivity (dB SPL, 1 Watt @ 1m)
MF108.5
HF110.5
Impedance (Ohms)
MF8
HF8
Power Handling, AES Standard (Watts)
MF400
HF200
Calculated Maximum Output (dB SPL)
MF Peak140.5
HF Peak139.5
MF Long Term134.5
HF Long Term133.5
Nominal Coverage Angle/-6 dB points (degrees)
Horizontal90
Vertical40
Recommended High-Pass Frequency
24 dB/Octave190 Hz
5.63
BACK
11.91
5.00
7.38
ARCHITECTURAL SPECIFICATIONS
The two-way mid/high lou dspeaker system shall incorpor ate
a 10-in cone MF tran sducer and a 2-in exit compressi on driver
HF transducer.
The MF driver shall be loaded into a midrange horn constructed of 3mm birch plywood r einfor ced with hi gh den sity
polyurethane foam. The MF horn shall incorporate a phase/
displacement plug. The HF driver shall be loaded on constant directivity horn with a nominal coverage pattern of
90° (h) x 40° (v). An internal passive filter network shall
provide system equalization.
System frequency response shall vary no more than ±3 dB
from 190 Hz to 19 kHz measured on axis. The midr ange frequency section shall prod uce a Sound Pressur e Level (SPL) of
108.5 dB SPL on axis at 1 meter with a power input of 1
Watt, and shall be capable of producing a peak output of
140.5 dB SPL on axis at 1 meter . The hi gh frequen cy secti on
shall produce a Sound Pressure Level (SPL) of 110.5 dB SPL
on axis at 1 meter with a power input of 1 W att, and shall be
capable of produ cin g a peak output of 139.5 dB SPL on axis
at 1 meter . The mi dr ange frequen cy section shall han dle 400
Watts of amplifier power (AES Standard) and shall have a
nominal impedance of 8 Ohms. The high frequency section
shall handle 200 Watts of amplifier power (AES Standard)
and shall have a nominal impedance of 8 Ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of 15mm thi ckness void-free cross-gr ainlaminated Baltic birch plywood and shall employ extensive
internal bracin g. It shall be finished in black catalyzed polyurethane. Input connectors shall be 4-terminal barrier strip
and one Neutrik NL4 Speakon. A total of sixteen 3/8"-16
threaded mounting/suspension points (4 each top, bottom
and sides) shall be provided. The front of the loudspeaker
shall be covered with a powder coated perforated steel grill.
The two-way mid/high loudspeaker shall be the EAW model
MQ1394.