EAW MQ1366e User Manual

Frequency Response (1 W @ 1m)

±3 dB 250 Hz to 12 kHz

-10 dB 200 Hz

Axial Sensitivity (dB SPL, 1 Watt @ 1m)

Passive 107

MF 109 HF 107

Impedance (Ohms)

Passive 8

MF 8 HF 8

Power Handling, AES Standard (Watts)

Passive 325

MF 400 HF 150

Calculated Maximum Output (dB SPL)

Passive Peak 138

MF Peak 141 HF Peak 135

Passive Long Term 132

MF Long Term 135 HF Long Term 129

Nominal Coverage Angle/-6 dB points (degrees)

Horizontal 60

Vertical 60

Recommended High-Pass Frequency

24 dB/Octave 200 Hz

SPECIFICATIONS MQ1366e

FEATURES

DESCRIPTION

PERFORMANCE

One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 info@eaw.com www.eaw.com EAW products are continually improved. All specifications are therefore subject to change without notice. MQ1366e/0002679/2 pp April 2002 Printed in USA

APPLICATION

PHYSICAL

Configuration Mid/High

Powering Passive or Bi-amplified

MF Subsystem 1x 10-in horn-loaded cone,

Radial Phase Plug™

HF Subsystem 1x 2-in exit/3-in voice voil com-

pression driver on constant directivity horn

Enclosure Materials

Exterior grade Baltic birch plywood

Finish

Wear resistant textured black paint

Connectors Terminal barrier strip

Suspension Hardware 16x 3/8"-16 threaded mounting

suspension points (4 each top, bottom and sides)

Grille Powder coated perforated steel

Dimensions inches millimeters

Height 40.00 1016

Width (front) 32.00 813

Width (rear) 8.12 206

Depth 25.61 650

Trapezoid Angle 25° per side

Weights pounds kilograms

Net Weight 148 67.3

Shipping Weight 156 71.0

• Dedicated horn loaded MF/HF array module

• 10-in MF w/ Radial Phase Plug™; 2-in exit

Neodymium HF

• 60° x 60° beamwidth

• Vertically configured to create horizontal arrays

A dedicated mid/high system in a vented trapezoidal enclosure. In clud es a horn-load ed 10-in MF con e with Radial Phase Plug™ and a 2-in exit/3-in diaphragm Neodymium compression driver. The MF and HF h orn s provi d e a nomin al 60° x 60° beamwidth. An in ternal passive cr ossover with jumpers on th e input panel allows user selection of either bi-amplified or passive operation. In either case digital signal processing is required to achieve specified performance. The enclosure features a comprehensive system of 3/8”-16 threaded suspension points.

The MQ1366e employs a no-compromise d esi gn wh ere th e mi d and high frequency horns are truly large enough to provide optimal pattern control thr oughout each passban d. Th e horn s feature a rigid but well-damped construction using wood veneer backed by structural foam. The MQ1366e has been designed to work with a complementary MQ1300 Series LF loudspeaker to create a full-range audio system, but may also be used without a LF complement for voice-only applications. The enclosure is vertically configured for arraying in horizontal rows. Horizontal arrays are typically used in venues, such as houses of worship, wher e the array must add r ess wide, f anshaped audiences.

Application Usage: Install

Houses of Worship Auditoriums Theatres Arenas Performing Arts Centers Stadiums

SPECIFICATIONS MQ1366e

DIMENSIONAL DRAWING

A & E SPECIFICATIONS

The 2-way mid/high loudspeaker shall incorporate a 10-in MF cone with Radial Phase Plug™, and a 2-in e xit/3-in diaphr agm HF compression driver. The MF and HF devices shall be loaded on horns that provide a nominal 60° x 60° beamwidth. An internal passive crossover n etwork shall offer eith er passive or bi-amplified operation, configurable via jumpers on the input panel.

System frequency respon se shall vary no m ore than 63 dB from 250 Hz to 12 kHz measured on axis. Wh en amplified using the internal passive crossover network, the loudspeaker shall produce a sound pressure level of 107 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 138 dB SPL on axis at 1 meter. It shall handle 325 watts of amplifier power (AES Standard) and shall have a nominal impedan ce o f 8 ohms. When bi-amplified , th e MF section shall produce a sound pressure level of 109 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 141 dB SPL on axis at 1 meter. It shall handle 400 watts of amplifier power (AES Standard) an d shall have a nominal impedance o f 8 ohm s. The HF section shall produce a sound pressure level of 107 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 135 dB SPL on axis at 1 meter. It shall handle 150 watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 ohms.

The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of e xterior grad e Baltic bir ch plywood and shall employ extensive intern al br acin g. I t shall be finish ed in wear-resistant textur ed black paint. Input connectors shall be a terminal strip. A total of 16x 3/8”-16 threaded mounting/suspension points (4 each top, bottom, and sides) shall be provided. The front of the loudspeaker shall be covered with a powder coated perforated steel grille.

The 2-way mid/high loudspeaker shall be the EAW model MQ1366e.

Manufacturing tolerances are +/- 0.13 and +/- 1°

(8.12)

25.61

12.00

40.00

GRILLE PARTIALLY SHOWN

11.91

5.00

12.16

23.28 50°

TOP

DIMENSIONS APPLY

TO TOP AND BOTTOM

32.00

FRONT

NOTES:

1. SYMBOL INDICATES MOUNTING POINT, 3/8-16 THREADED HOLE (PI ANGLE).

2. SYMBOL INDICATES NON LOAD BEARING MOUNTING POINT, 3/8-16 THREADED HOLE (PI ANGLE).

3. SYMBOL INDICATES CENTER OF BALANCE.

4. WEIGHT APPROX. 164 LBS.

5. SHIPPING WEIGHT APPROX. 182 LBS.

6.37

36.10

(1.95)

VIEW A-A

DIMENSIONS APPLY

TO BOTH SIDES

MQ1366e

13.15

5.00

11.89

BACK

4.00

34.93

20.00

INPUT

2.54