EAW CAM160 User Manual

DESCRIPTION
The EAW Commercial CAM160 is an integrated audio mixer and power amplier outtted with comprehensive input/output facilities and feature sets to provide exceptional versatility from a highly cost­eective package. Designed for a wide range of xed installation applications, the CAM160 oers “all in one” functionality without need for add-ons such as expansion modules.
CAM160
8 INPUT x 1 OUTPUT 160 W MIXER-AMPLIFIER
Features
Inputs 1 and 2 are divided into four discrete input sections: a combination XLR/TRS connector, Phoenix connector, or terminal strip. Meanwhile, Inputs 3, 4, 5 and 6 oer both Phoenix connectors and terminal strips. Two pairs of RCA connectors allow unbalanced auxiliary (Aux) signals to enter the amplier via Aux 1 and Aux 2, both of which are attenuated by a potentiometer on the front of the amplier.
Two levels of priority can be established on Inputs 1 and 2, initiated with external contact closures or adjustable signal threshold levels. External volume control is possible through a Phoenix connector and user supplied potentiometer. A two-position Phoenix connector allows the internal fault relay to be connected to redundant systems. And, an adjustable pre-announcement chime is also included.
Front panel controls include a level control for each input, a toggle switch for Aux 1 or Aux 2 selection, and one Aux master level control for the selected Aux. Low and high EQ controls oers 12 dB of boost or cut at 100 Hz and 10 kHz, respectively. A master volume control aords output volume control, while distinctive LEDs indicate power (green), signal (amber), overload (red), and fault (red).
The CAM160 provides 160 watts of output power at 100 volts,
70.7 volts, 25 volts and 4 Ohms. An intelligent output stage is fully protected against permanent damage caused by overloading, shorts and thermal faults.
• Two combination 1/4-inch/XLR/Phoenix, or barrier strip Mic/Line inputs
• Four Phoenix connector or barrier strip Mic/Line inputs
• Selectable 24-volt phantom power
• Two stereo auxiliary inputs
• Multiple priority levels
• Transformer-balanced telephone paging on Input 1
• Signal processing loop
• Internal fault-activated relay
• Ex ternal volume control
• 4-Ohm, 25-volt, 70-volt and 100-volt outputs
• Automatic changeover to 24-volt DC backup power
• Universal power supply
• UL Approved
Applications
The CAM160 will operate on 100 volts to 240 volts AC power (50/60 Hz), and is supplied by a detachable IEC power cord. A combination banana plug/binding post connection is also provided for connecting an external 24-volt DCbackup battery.
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | TEL toll free within US/Canada 800.992.5013
TEL outside US 508.234.6158 | FAX 508.234.8251 | Page 1 of 2
• Paging Systems • Houses of Worship
• Hotel and Ballrooms • Meeting Rooms
• Schools • Oces
• Foreground/Background Music Systems
Part No. 0019318 Rev. A 11/08
PERFORMANCE
Input 1-8 (balanced / unbalanced)
Impedance
Mic Balanced, 2.7k Ohm Line Balanced, 30k Ohm Aux Unbalanced, 15k Ohm
Input Protection
RFI and Level Protected
Input Gain Trim Range
-3dB to 40dB (Mic Input)
-23dB to 20dB (Line input)
Max Input Level
+19dBV
Microphone Input E.I.N. (20Hz – 20kHz)
-124dBV
Common Mode Rejection Ratio (1kHz)
Mic Input 60dB Typical Line Input 30dB Typical
Dynamic Range
105dB
Frequency Response
20Hz – 20kHz +/-1dB
Distortion
<0.1% 20Hz – 20kHz
Operating Range (+0dB/- 3dB)
40Hz – 15kHz
Output Power
160W @ 100V 160W @ 70.7V 160W @ 25V 160W @ 4 Ohm
PHYSICAL Front Controls
Type Range
Inputs 1-6 Level 0 to 10 Aux 1 and 2 Level 0 to 10 EQ Lo +/- 12dB @ 100Hz High +/- 12dB @ 10 kHz Volume Level 0 to 10 Power AC Mains On/Off Aux 1 or 2 Selector Toggle 1 or 2
CAM160
8 INPUT x 1 OUTPUT 160 W MIXER-AMPLIFIER
Rear Controls
Type Range
Inputs 1–6 Trim Pot -3dB to 40dB (Mic Input)
-23dB to 20dB (Line Input) Inputs 1–2 DIP Line, Mic, 24V Phantom,
Ducking Threshold, Transformer enable (Input 1 only), High-Pass Filter, 10 dB Pad
Inputs 3–6 DIP Line, Mic, 24V Phantom, High-Pass Filter, 10 dB Pad
100Hz HPF In/Out Priority Depth Adjustment +/- 10dB Chime Level +/- 10dB External Volume Control 3 Position Phoenix Fault Relay 2 Position Phoenix
Mains Power
AC 100Hz – 240HzVAC 50/60 Hz 220W DC 24V
Dimensions (inches)
H x W x D with feet 4.0 x 17.25 x 14.6 w/o feet 3.5 x 17.25 x 14.6
Dimensions (millimeters)
H x W x D with feet 102 x 483 x 381 w/o feet 88 x 483 x 381
Weight (approximate net lb/kg)
20.8 9.3
Shipping weight (lb/kg)
24 10.7
EMC STANDARDS:
U.S. -part 15 of the FCC Rules, EN55103-1, EN55103-2, EN55022 (Emissions), EN55024 (Immunity), C-Tick N484, Canada - ICES-003
SAFETY STANDARDS:
cTUVus, UL, cULus
ORDERING DATA:
P/N 0020860
Height w/ feet:
4 in
102 mm
Width: 17.25 in / 438 mm
Overall width: 19 in / 483 mm
Height
3.5 in 88 mm
Overall depth: 16.5 in / 419 mm
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | TEL toll free within US/Canada 800.992.5013
TEL outside US 508.234.6158 | FAX 508.234.8251 | Page 2 of 2
Part No. 0019318 Rev. A 11/08
Depth:
14.6 in / 381 mm