EAW AC-TX64, AC-TX128 Instruction Manual & Cooking Manual

INSTRUCTION MANUAL

AC-TX64

70 Volt/100 Volt Transformer Panel
for VR61 and VR62 Loudspeakers
and the CLA37 Column Loudspeaker

AC-TX128

70 Volt/100 Volt Transformer Panel
for VR21 and VR51 Loudspeakers

2 – AC-TX64 and AC-TX128

AC-TX64 and AC-TX128 – 3

1. SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.

9. Only use attachments/accessories specied by the manufacturer.

10. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

11. The entire sound system must be designed in compliance with the current standards and laws
regarding electrical systems.

12. When installing and using this apparatus, keep in mind the technical specications indicated in the
dedicated section of the manual.

WARNING! This equipment has been designed to be installed by qualied professionals only!
There are many factors to be considered when installing professional sound reinforcement systems,

including mechanical and electrical considerations, as well as acoustic coverage and performance.
EAW Commercial strongly recommends that this equipment be installed only by a professional sound
installer or contractor.

Part No. 0012133 Rev.A 02/2005

©2005 LOUD Technologies Inc. All Rights Reserved. Printed in China.

TABLE OF CONTENTS

1. SAFETY INSTRUCTIONS ........................................................ 2

2. INTRODUCTION....................................................................... 3

3. INSTALLATION ........................................................................ 3

4. CONNECTIONS........................................................................ 4

5. EXAMPLES ............................................................................... 5

6. SPECIFICATIONS..................................................................... 6

7 . SERVICE................................................................................... 6

8. WARRANTY ............................................................................. 7

The exclamation point within an
equilateral triangle is intended to

alert the user of the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the apparatus.

AC-TX64 and AC-TX128 – 3

2. INTRODUCTION

Congratulations on the purchase of your new EAW Commercial 70 Volt/100 Volt
transformer panel. These panels allow you to congure the VR Series Loudspeakers and the
CLA37 Column Loudspeaker for use in 70 Volt or 100 Volt distributed systems.

• The AC-TX64 transformer panel can be used in the VR61, VR62 or CLA37
Loudspeakers, in place of the input terminal plate.

• The AC-TX128 transformer panel can be used in the VR21 or VR51 Loudspeakers.

3. INSTALLATION

Unpacking and Inspection

Visually inspect the outside of the shipping carton and check for any shipping damage.
After unpacking, if you nd concealed damage, save the packing materials for the carrier’s
inspection, notify the carrier immediately, and le a shipping damage claim. Although EAW
Commercial will help in any way possible, it is always the responsibility of the receiving
party to le any shipping damage claim. The carrier will help prepare and le this claim.

Installation Procedure

1. Remove any external speaker wires
from your Loudspeaker’s input
terminals, and remove the six screws
securing the input panel.

2. Remove the internal wires from the
back of the input panel, and put the
input panel in a safe place for future
use.

3. Connect the Positive (white) wire
from the Loudspeaker to the white
wire from the transformer.

4. Connect the Negative (black) wire
from the Loudspeaker to the black
wire from the transformer.

5. Fit the transformer panel to the
Loudspeaker, with the transformer
inside, and secure using the six
screws from step 1. Make sure
the two wires are not accidentally
pinched.

NOTE: For the CLA37, the
transformer panel must be installed
upside down, so the transformer is
at the top, and does not interfere
with the CLA37 drivers.

1

00V

BLACK

WHITE