Eaton Zeta 3, Zetalite 3 Installation Instructions Manual

4

2

1

3

Installation Instructions for:

Zeta 3

IP65

 Product luminaires comply with EN60598 and are suitable for use in normal interior/exterior conditions.

o o

 This luminaire has an ambient temperature range of 5 C to 25 C.

Cable Entry

NOTE: If the fitting is required to be IP65 rated, ensure a suitable IP65 rated cable
gland is used to seal cable entry.
For BESA entry or fixing points, fit to a flat surface. Sealant or suitable sealing
washers should be applied around fixing screw heads to maintain the ingress
protection of the luminaire.

Cable Entry with

Besa entry available

Cable Entry

Cable Entry

Optional Gasket

If fitting is required to be IP65 rated,
ensure gasket is fitted around outside
groove. If not required, please discard.

Fitting the Legend (Ordered separately)

Self adhesive legends
can be fitted to the
front face, use
soapy water to
position correctly.

Take base of fitting, knock through the preferred cable entry point.
Note: Centre cable entry requires drilling. Using the hexagonal
pattern, knock out suitable points and mount to fixing surface, if
wall mounted ensure battery clips are at the bottom of the fitting

Using a screwdriver, release 4 x clips
and remove transparent lid.
Remove the battery and gasket from
the base.

Clip battery back into position

Feed mains cable
through cable entry
and wire the PCB on
the lid as per below,
connect the battery
lead to the PCB

Refit lid on to the base, ensuring the
capacitors are the opposite side to
the battery in the base. Ensure tabs
are fully fastened to ensure IP rating

Zeta 3 can be operated in
Maintained or Non-Maintained
mode by cutting or removing the
link on the PCB.

Note: There is 'no' switched
input supply to the luminaire
and therefore cannot be remotely
switched between maintained
and non-maintained operation.

Link Wire

Terminal Block:
L - Live (Brown)
N - Neutral (Blue)

Wiring

ENSURE ALL 4 CLIPS ARE RELEASED,

FORCING OPEN WITH ONLY 2 CLIPS

OPEN WILL DAMAGE THE OTHER CLIPS

K983V4

IMPORTANT NOTE:

 Luminaire battery MUST NOT be connected until building has a permanent un-switched live supply.
 Repeated full discharges caused by fully removing power to luminaires with connected batteries (i.e. a nightly building power

down prior to hand over) will permanently damage the battery and invalidate any warranty.

Testing Maintained:

The unit should be connected to an unswitched live supply, which should be connected to the normal lighting sub-circuit in that
location. The LED indication should be checked to ensure that it is illuminated, this indicates that the batteries are charging.
A short discharge should be performed to check that the units are operating correctly. This is carried out by interrupting the
unswitched supply at the distribution board or by isolating the appropriate unswitched supply sub-circuit. The supply should
then be restored and the LED indication checked. After 24hrs carry out a full rated discharge test. The testing regime as
defined in EN 50172 should then be implemented. Alternatively, Self-Check products carry out a full rated duration test after 36
hours automatically and then preform automated tests to EN50172. See leaflet K1037 for further details.
If the unit no longer meets the emergency duration the battery must be replaced with a battery of the same type.
When used as intended this product complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2012/19/EU.
Date of commissioning to be entered in the space provided on the battery label by either the installer or commissioning
engineer.

Safe Operation

1. Check the rating label for voltage and frequency before connecting this luminaire to the electrical supply.

2. Ensure that the mains supply is switched off when working on this luminaire, whether installing or carrying out any other
servicing.

3. To prevent damage to driver, do not mix with conventional magnetic ballasts on the same electrical circuit.

4. Where use in more onerous situations is required, e.g. In part-completed buildings before “drying-out” is completed, or
areas where ambient temperatures are outside the normal temperature range, then consult our Sales Office.

5. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar
qualified person

Servicing and Disposal

1. At commissioning and handing over of installation ensure that a copy of these instructions is presented to the authority
responsible for the operation and maintenance of the luminaries.

2. Servicing, e.g. cleaning, must only be carried out after the electricity supply has been switched off. It must not be assumed
that luminaries with lamps not lit are switched off-always check before servicing.

3. Cleaning should be carried out at regular intervals to ensure that dirt does not accumulate to an extent that will impair the
thermal safety or optical performance of the luminaire. Regular cleaning will also ensure that the optical performance of the
luminaries is maintained.

4. Avoid touching the LED array surface. To clean - Blow surface with either dry air or nitrogen gas.

5. At the end of life the luminaire is classed as WEEE under directive 2002/96/EC and should be disposed of in accordance
with local legislation.

Luminaire Cleaning

End of Life and Components Disposal

WEEE