Eaton MN024002EN User Manual

Comm Module

MN024002EN Effective February 2017

NPServe Users Guide

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY

The information, recommendations, descriptions and safety notations in this document are based on Eaton Corporation’s
(“Eaton”) experience and judgment and may not cover all contingencies. If further information is required, an Eaton sales
office should be consulted. Sale of the product shown in this literature is subject to the terms and conditions outlined in
appropriate Eaton selling policies or other contractual agreement between Eaton and the purchaser.

THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES
OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY
EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF EATON. THE
CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES.

In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or
otherwise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to
damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the use of
existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the information,
recommendations and descriptions contained herein. The information contained in this manual is subject to change without
notice.

ii USERS GUIDE MN024002EN February 2017

Contents

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY ................................... ii

SAFETY FOR LIFE .........................................................................iv

SAFETY INFORMATION ....................................................................iv

Safety instructions .............................................................................. iv

NPSERVE USERS GUIDE ................................................................... 1

Connections ....................................................................................1

Connection details ...............................................................................2

Real-time data ..................................................................................3

Configuration ...................................................................................3

DNP SCADA ...................................................................................4

Diagnostics ....................................................................................5

System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

USB maintenance port ...........................................................................5

iiiUSERS GUIDE MN024002EN February 2017

NPServe Users Guide

!

!

SAFETY

FOR LIFE

Eaton meets or exceeds all applicable industry standards relating to product safety. We actively promote safe practices in
the use and maintenance of our products through our service literature, instructional training programs, and the continuous
efforts of all Eaton employees involved in product design, manufacture, marketing, and service.

We strongly urge that you always follow all locally approved safety procedures and safety instructions when working around
high voltage lines and equipment, and support our “Safety For Life” mission.

Safety for life

SAFETY

FOR LIFE

Safety information

The instructions in this manual are not intended as a
substitute for proper training or adequate experience in the
safe operation of the equipment described. Only competent
technicians who are familiar with this equipment should
install, operate, and service it.

A competent technician has these qualifications:



Is thoroughly familiar with these instructions.



Is trained in industry-accepted high and low-voltage safe
operating practices and procedures.



Is trained and authorized to energize, de-energize, clear,
and ground power distribution equipment.



Is trained in the care and use of protective equipment
such as arc flash clothing, safety glasses, face shield,
hard hat, rubber gloves, clampstick, hotstick, etc.

Following is important safety information. For safe
installation and operation of this equipment, be sure to read
and understand all cautions and warnings.

Safety instructions

Following are general caution and warning statements that
apply to this equipment. Additional statements, related to
specific tasks and procedures, are located throughout the
manual.

DANGER

Hazardous voltage. Contact with hazardous voltage will
cause death or severe personal injury. Follow all locally
approved safety procedures when working around high­and low-voltage lines and equipment. G103.3

WARNING

Before installing, operating, maintaining, or testing this
equipment, carefully read and understand the contents
of this manual. Improper operation, handling or
maintenance can result in death, severe personal injury,
and equipment damage. G101.0

Hazard Statement Definitions

This manual may contain four types of hazard statements:

DANGER

Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

CAUTION

Indicates a potentially hazardous situation which, if not
avoided, may result in equipment damage only.

WARNING

This equipment is not intended to protect human
life. Follow all locally approved procedures and safety
practices when installing or operating this equipment.
Failure to comply can result in death, severe personal
injury and equipment damage. G102.1

WARNING

Power distribution and transmission equipment must
be properly selected for the intended application. It
must be installed and serviced by competent personnel
who have been trained and understand proper safety
procedures. These instructions are written for such
personnel and are not a substitute for adequate training
and experience in safety procedures. Failure to properly
select, install or maintain power distribution and
transmission equipment can result in death, severe
personal injury, and equipment damage. G122.2

iv

USERS GUIDE MN024002EN February 2017