Eaton MBP11K208, HotSwap MBP Series, MBP6K208 Installation And User Manual
ENGLISH
HotSwap MBP
Maintenance Bypass
MBP6K208
MBP11K208
Installation
and user manual
Copyright © 2012 EATON
All rights reserved.
Service and support:
Call your local service representative
SK-90610-Y4_EN
Page 2
SK-90610-Y4_EN
Special symbols
The following are examples of symbols used on the Hotswap MBP to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.
Important instructions that must always be followed.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)
in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
Information, advice, help.
Refer to the user manual of UPS.
SAVE THESE INSTRUCTIONS. This manual contains important instructions
that should be followed during installation and maintenance of the MBP and UPS.
The Hotswap MBP models that are covered in this manual are intended for installation
in an environment within 0 to 40°C, free of conductive contaminant.
This equipment has been tested and found to comply with Class A UPS,pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Certication standards (in use with UPS)
p Safety: IEC/EN 62040-1 / Ed.1: 2008.
UL 1778 4
th
edition
p EMC: IEC 62040-2 / Ed.2: 2005
EN 62040-2 / Ed.2: 2006
FCC part 15 Class A.
p Performance: IEC/EN 62040-3 / Ed.2.0: 2011.
p IEC 61000-4-2 (ESD): level 3.
p IEC 61000-4-3 (Radiated eld): level 3.
p IEC 61000-4-4 (EFT): level 4.
p IEC 61000-4-5 (Fast transients): level 4.
p IEC 61000-4-6 (Electromagnetic eld): level 3.
p IEC 61000-4-8 (Conducted magnetic eld): level 4.
SAFETY INSTRUCTIONS
Page 3
SK-90610-Y4_EN
ENGLISH
Safety of persons
p The system has its own power source when connected to the UPS (UPS battery). Consequently,
the power outlets may be energized even if the system is disconnected from the AC power source.
Dangerous voltage levels are present within the system.
It should be opened exclusively by qualied service personnel.
p The product must be properly grounded, always connect the earth wire rst
Product safety
p The MBP connection instructions and operation described in the manual must be followed
in the indicated order. Disconnection and overcurrent protection devices shall be provided by others
for AC in/out circuits.
p CAUTION - To reduce the risk of re, the unit connects only to a circuit provided with branch circuit
overcurrent protection (please refer to the UPS User Manual for current rating), in accordance with
the National Electric Code, ANSI/NFPA 70 (US installations only).
The upstream circuit breaker must be easily accessible.
The unit can be disconnected from AC power source by opening this circuit breaker, and if still
connected to UPS, by previously shutting down the UPS (refer to the UPS User Manual)
p Check that the indications on the rating plate correspond to your AC powered system and to the
actual electrical consumption of all the equipment to be connected to the system.
p Never install the system near liquids or in an excessively damp environment.
p Never let a foreign body penetrate inside the system.
p Never expose the system to direct sunlight or source of heat.
p If the system must be stored prior to installation, storage must be in a dry place.
p The admissible storage temperature range is -15ºC to +60ºC.
Special precautions
p The Hotswap MBP is designed to work with approved EATON UPS (contact your Eaton reseller for
more information)
p All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.
There are NO USER SERVICEABLE PARTS inside the MBP.
SAFETY INSTRUCTIONS
Page 4
SK-90610-Y4_EN
1. Introduction ....................................................................................... 5
1.1 Environmental protection ...................................................................................................5
2. Presentation ...................................................................................... 6
2.1 Standard positions .............................................................................................................6
2.2 Description / Panels ...........................................................................................................8
3. Installation ........................................................................................ 9
3.1 Inspecting the equipment ..................................................................................................9
3.2 Unpacking the MBP ...........................................................................................................9
3.3 Checking the accessory kit ................................................................................................9
3.4 Mechanical Mounting ...................................................................................................... 10
3.5 Installation requirements ................................................................................................. 10
4. Power cables connection ................................................................11
4.1 MBP6K208 ...................................................................................................................... 11
4.2 MBP11K208 ..................................................................................................................... 12
5. Operations ....................................................................................... 14
5.1 UPS start-up with HotSwap MBP .................................................................................... 14
5.2 UPS replacement with HotSwap MBP ............................................................................ 15
5.3 UPS maintenance with HotSwap MBP ...........................................................................17
6. Specifications .................................................................................. 18
Contents
Page 5
SK-90610-Y4_EN
ENGLISH
1. Introduction
Thank you for selecting an EATON product to protect your electrical equipment.
The HotSwap MBP range has been designed with the utmost care.
We recommend that you take the time to read this manual to take full advantage of the many features
of your MBP (Maintenance Bypass).
Before installing your HotSwap MBP with your UPS, please read rst the safety instructions.
Then follow the indications in this manual, which completes the UPS Installation and User Manual.
To discover the entire range of EATON products, we invite you to visit our web site at www.eaton.com/
powerquality or contact your EATON representative.
1.1 Environmental protection
EATON has implemented an environmental-protection policy.
Products are developed according to an eco-design approach.
Substances
This product does not contain CFCs, HCFCs or asbestos.
Packing
To improve waste treatment and facilitate recycling, separate the various packing components.
p The cardboard we use comprises over 50% of recycled cardboard.
p Sacks and bags are made of polyethylene.
p Packing materials are recyclable and bear the appropriate identication symbol
01
PET
Materials Abbreviations
Number in
01
PET
the symbols
Polyethylene terephthalat PET 01
High-density polyethylene HDPE 02
Polyvinyl chloride PVC 03
Low-density polyethylene LDPE 04
Polypropylene PP 05
Polystyrene PS 06
Follow all local regulations for the disposal of packing materials.
End of life
EATON will process products at the end of their service life in compliance with local regulations. EATON
works with companies in charge of collecting and eliminating our products at the end of their service life.
Product
The product is made up of recyclable materials.
Dismantling and destruction must take place in compliance with all local regulations concerning waste.
At the end of its service life, the product must be transported to a processing center for electrical and
electronic waste.
Page 6
SK-90610-Y4_EN
2. Presentation
The Eaton® HotSwap MBP module makes it possible to service or even replace the UPS without affecting
the connected loads (HotSwap function).
You can safely eliminate the effects of UPS maintenance and guard the integrity of your equipment.
Providing outstanding reliability, the Eaton HotSwap MBP unique benets include:
p Easy and fast connection to UPS due to Input/Output and signal “all in one” patented connector
(Hotswap MBP 5/6kVA range)
p “make before break” feature to allow full servicing (electrical power continuity) when switching from
UPS position to Bypass (and vice versa)
p Communication feature with UPS*: detection of MBP connection and switch position (Normal or Bypass)
(* works only with some approved EATON UPS - contact your Eaton reseller for more information)
p Load connection by both terminal blocks and NEMA outlets (30 A L6-30R)
p Adjustable 19’’ Rack kit and multiple positions Tower installation kit provided
p Backed by worldwide agency approvals.
2.1 Standard positions
MBP6K208
Tower installation
Rack installation Wall mounting
Loading...