Eaton HHB1POWR User Manual

Range Extender Components
Home Key™ Slide Channel
Antenna
Plugs into
standard
grounded
outlet
(3-prong)
Status LED
Range Extender Uses:
Expand the transmission zone to reach sensors that are farther away from the Base Station.* Perfect for:
• Large houses
• Houses with thick walls and floors
• Houses with obstructions
*Actual range may vary, depending on the location of the Base Station and home construction.
FCC Statement
(Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfere nce, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING (Part 15.21): Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
To comply with F CC’s RF expo sure limits for ge neral population/un controlled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Statement
The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Interference
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection agai nst harmful int erference i n a residential installation. This equi pment generates, uses, and can radiate radio freque ncy energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter ference to radio or televi sion recept ion, which can be determined by turning the equipment off and on, then the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into a power source on different circuit than the receiver.
Sensor Maintenance
No serviceable parts. Clean with a soft, dry cloth.
IM00416008E Rev. 2 Part No.: 67A5006H02
© 2006 Eaton Corporation
Range Extender
Range Extender
Plug in
CARRY the Range Extender and the Home Key to the wall outlet where you want to place it. Choose an outlet that is not controlled with a wall switch.
PLUG the Range Extender into the wall outlet. The green light on the front will blink quickly several times.
Set up
After the light stops blinking, CLICK the thumbwheel to wake the Home Key if it is asleep, then SLIDE the Home Key into the channel on the top of the sensor. The Home Key screen should say:
Please wait… Device found OK to remove Key.
Follow the instructions on the Home Key screen to join the Range Extender to your system, name it, and set In-Home
Awareness and "CallMe" Awareness .
Device found
OK to remove Key...
If you slide the Home Key into the sensor Slide Channel and the Home Key screen shows either of the following messages, it means that the Home Key or sensor may be outside the range of the Base Station.
Remove Key...
Please try again
Sensor out of range?
Remove Key... Can't set up now Key out of range
If the Home Key or sensor is out of range, you can:
• Add a Home Heartbeat Range Extender between the Base Station and Range Extender, or
• select an alternate location for the Range Extender, or
• try moving the Base Station to a more central location in your home. Then, complete Step 1 again.
The Awareness settings let you choose to have Home Heartbeat alert you if the Range Extender has lost its connection with the system (Off Mesh), or has a poor, okay, or good connection.
Good Mesh is the strongest and indicates a high quality signal between the Base Station and the Range Extender. Okay Mesh and Poor Mesh indicate a connection of varying degree. Off Mesh is indicated when the Range Extender has lost the connection with the Base Station. If the Range Extender loses its Good Mesh frequently, try an alternate location or extra Range Extender to help maintain a good connection.
Use
After the Range Extender is joined to the system, the green light will be steady. If the light blinks slowly, it means that the unit has lost the connection to the Base Station and its status will change to Off Mesh.
Sensor
Range Extender
Sensor
Sensor
Base Station
Sensor
The Range Extender will try to re-establish a connection with the Base Station, but if it is unable to, or if the Range Extender frequently loses its connection, try an alternate location and repeat Steps 1 and 2. When a device is communicating through the Range Extender, the green light on the front will blink rapidly.
Need help? Call 1-800-813-2199 for customer support or visit www.homeheartbeat.com
If Your Range Extender . . .
• will not respond, make sure the outlet it is plugged into actually has power.
• frequently goes to Off Mesh, move the Range Extender closer to the Base Station, or add an additional Home Heartbeat Range Extender.
Loading...
+ 2 hidden pages