How it Works
Eaton
Loading...
EASY410-DC-TE
operation manual
240 pgs3.11 Mb0
User Manual
5 pgs223.53 Kb0
operation manual [de]
240 pgs4.47 Mb0
User Manual [de]
5 pgs224.98 Kb0
Table of contents
Loading...

Eaton EASY410-DC-TE operation manual

Operating Instructions
Control Relay 500, 700
05/10 MN05013003Z-EN
replaces 05/04 AWB2528-1508GB
Emergency On Call Service
Please call your local representative:
http://www.eaton.com/moeller/aftersales
or Hotline of the After Sales Service: +49 (0) 180 5 223822 (de, en)
AfterSalesEGBonn@eaton.com
Original Operating Instructions
The German-language edition of this document is the original operating manual.
Translation of the original operating manual
All editions of this document other than those in German language are translations of the original German manual.
1
st
published 2004, edition date 05/04,
2
nd
edition 05/10, See revision protocol in the “About this manual“ chapter
© 2004 by Eaton Industries GmbH, 53105 Bonn
Production:DHW Translation:globaldocs GmbH
All rights reserved, including those of the translation.
No part of this manual may be reproduced in any form (printed, photocopy, microfilm or any other process) or processed, duplicated or distributed by means of electronic systems without written permission of Eaton Industries GmbH, Bonn.
Subject to alteration without notice.
Danger! Dangerous electrical voltage!

Before commencing the installation

• Disconnect the power supply of the device.
• Ensure that devices cannot be accidentally restarted.
• Verify isolation from the supply.
• Earth and short circuit.
• Cover or enclose neighbouring units that are live.
• Follow the engineering instructions (AWA) of the device concerned.
• Only suitably qualified personnel in accordance with EN 50110-1/-2 (VDE 0105 Part 100) may work on this device/system.
• Before installation and before touching the device ensure that you are free of electrostatic charge.
• The functional earth (FE) must be connected to the protective earth (PE) or to the potential equalisation. The system installer is responsible for implementing this connection.
• Connecting cables and signal lines should be installed so that inductive or capacitive interference does not impair the automation functions.
• Install automation devices and related operating elements in such a way that they are well protected against unintentional operation.
• Suitable safety hardware and software measures should be implemented for the I/O interface so that a line or wire breakage on the signal side does not result in undefined states in the automation devices.
• Ensure a reliable electrical isolation of the low voltage for the 24 volt supply. Only use power supply units complying with IEC 60364-4-41 (VDE 0100 Part 410) or HD 384.4.41 S2.
• Deviations of the mains voltage from the rated value must not exceed the tolerance limits given in the specifications, otherwise this may cause malfunction and dangerous operation.
• Emergency stop devices complying with IEC/EN 60204-1 must be effective in all operating modes of the automation devices. Unlatching the emergency-stop devices must not cause restart.
• Devices that are designed for mounting in housings or control cabinets must only be operated and controlled after they have been installed with the housing closed. Desktop or portable units must only be operated and controlled in enclosed housings.
• Measures should be taken to ensure the proper restart of programs interrupted after a voltage dip or failure. This should not cause dangerous operating states even for a short time. If necessary, emergency-stop devices should be implemented.
• Wherever faults in the automation system may cause damage to persons or property, external measures must be implemented to ensure a safe operating state in the event of a fault or malfunction (for example, by means of separate limit switches, mechanical interlocks etc.).
Moeller GmbH
Safety instructions
I
II

Contents

0 About This Manual..................................................................... 7
0.1 List of revisions ............................................................................ 7
0.2 Device designation....................................................................... 7
0.3 Writing conventions ..................................................................... 8
1 .............................................................................................. 9
1.1 Target group................................................................................. 9
1.2 Proper use.................................................................................... 9
1.2.1 Improper use................................................................................ 9
1.3 Overview...................................................................................... 10
1.4 Versions ....................................................................................... 12
1.4.1 Key to part numbers..................................................................... 14
1.5 operating principles ............................................................... 15
1.5.1 Key Pad ........................................................................................ 15
1.5.2 Selecting menus and entering values .......................................... 15
1.5.3 Choosing the main and system menu ......................................... 16
1.5.4 Status indicator  .................................................................... 17
1.5.5 Status display for local expansion ................................................ 17
1.5.6 Advanced Status display .............................................................. 17
1.5.7 LED display ........................................................................... 18
1.5.8 Menu structure ............................................................................ 18
1.5.9 Selecting or toggling between menu items................................. 22
1.5.10 Cursor display............................................................................... 22
1.5.11 Set value ...................................................................................... 23
2 Installation .................................................................................. 25
2.1 Mounting...................................................................................... 26
2.1.1 Mounting on top-hat rail............................................................... 26
2.1.2 Screw mounting........................................................................... 27
2.2 Connecting the expansion device ................................................ 28
2.3 Terminations ................................................................................ 29
2.3.1 Tools............................................................................................. 29
2.3.2 Cable cross-sections .................................................................... 29
2.4 Connecting the power supply ...................................................... 29
2.4.1 Cable protection ........................................................................... 29
2.4.2 Supplying AC basic units.............................................................. 29
2.4.3 Supplying AC expansion units...................................................... 30
2.4.4 Supplying DC basic units.............................................................. 31
2.4.5 Supplying DC expansion devices ................................................. 31
2.5 Connecting inputs ........................................................................ 32
2.5.1 Connect digital AC inputs............................................................. 32
2.5.2 Connecting easy DC digital inputs ............................................... 36
2.5.3 Connecting analog inputs............................................................. 37
2.5.4 Connecting high-speed counters and frequency generators ....... 41
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 1
2.6 Connecting outputs...................................................................... 42
2.6.1 Connecting relay outputs............................................................. 42
2.6.2 Connecting transistor outputs...................................................... 44
2.6.3 Behavior in the event of a short-circuit/overload.......................... 46
2.7 Expanding inputs/outputs . .......................................................... 46
2.7.1 Local expansion module .............................................................. 47
2.7.2 Remote expansion....................................................................... 48
2.8 Connecting bus systems ............................................................. 49
3 Placing into operation ............................................................... 51
3.1 Switch-on..................................................................................... 51
3.2 Setting the menu language.......................................................... 51
3.3 operating modes ................................................................... 52
3.4 Creating your first circuit diagram................................................ 52
3.4.1 Circuit diagram display................................................................. 54
3.4.2 From the first contact to the output coil ...................................... 55
3.4.3 Wiring .......................................................................................... 55
3.4.4 Testing the circuit diagram........................................................... 57
3.4.5 Deleting the circuit diagram......................................................... 58
3.4.6 Fast circuit diagram entry............................................................. 58
4 Wiring with ........................................................................ 59
4.1 -operation .............................................................................. 59
4.1.1 Buttons for editing circuit diagrams and function relays.............. 59
4.1.2 Operation ..................................................................................... 59
4.1.3 Relays, function relays................................................................. 63
4.1.4 Saving and loading circuit diagrams ............................................. 65
4.2 Working with contacts and relays................................................ 66
4.2.1 Input and output contacts............................................................ 66
4.2.2 Creating and modifying connections............................................ 68
4.2.3 Inserting and deleting a rung ....................................................... 69
4.2.4 Switching with the Cursor Buttons.............................................. 70
4.2.5 Checking the circuit diagram........................................................ 71
4.2.6 Coil Functions .............................................................................. 72
4.3 Function Relays............................................................................ 77
4.3.1 Example: with function relay timer and counter relay.................. 78
4.4 Analog value comparator/threshold value switch ........................ 82
4.4.1 Circuit diagram display with analog value comparator ................. 84
4.4.2 Compatibility with 400 with500 and 600 with
700 ........................................................................................ 84
4.4.3 Parameter display in RUN mode.................................................. 85
4.4.4 Resolution of the analog inputs ................................................... 86
4.4.5 Function of the analog value comparator function relay .............. 86
4.5 Counter ........................................................................................ 94
4.5.1 Function of the counter function relay......................................... 97
4.6 High-speed counters, -DA, -DC...................................... 100
4.6.1 Frequency Counter ...................................................................... 100
2 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
4.6.2 High-speed counters.................................................................... 103
4.7 Text Display.................................................................................. 109
4.7.1 Wiring a text display..................................................................... 109
4.7.2 Retention...................................................................................... 109
4.7.3 Scaling.......................................................................................... 110
4.7.4 Function ....................................................................................... 110
4.7.5 Text Entry..................................................................................... 111
4.7.6 Font .............................................................................................. 111
4.7.7 Entering a setpoint in a display .................................................... 111
4.8 Weekly timer................................................................................ 113
4.8.1 Parameter display and parameter set for weekly timer: .............. 114
4.8.2 Changing time switch channel ..................................................... 115
4.8.3 Function of the weekly timer (example parameter setting) ......... 115
4.9 Operating Hours Counter ............................................................. 118
4.9.1 Value range of the operating hours counter................................. 119
4.9.2 Accuracy of the operating hours counter..................................... 119
4.9.3 Function of the operating hours counter function relay ............... 119
4.10 Timing Relay................................................................................. 122
4.10.1 Parameter display and parameter set for a timing relay:.............. 123
4.10.2 Retention...................................................................................... 124
4.10.3 Timing relay modes...................................................................... 124
4.10.4 Time Range.................................................................................. 125
4.10.5 Function of the timing relay function relay................................... 127
4.10.6 Examples timing relay.................................................................. 132
4.11 Jumps .......................................................................................... 135
4.11.1 Function ....................................................................................... 135
4.11.2 Power Flow Display ..................................................................... 136
4.12 Year Time Switch ......................................................................... 137
4.12.1 Function ....................................................................................... 137
4.12.2 Behavior in the event of a power failure ...................................... 138
4.12.3 Wiring of a year time switch ........................................................ 138
4.12.4 Parameter display and parameter set for year time switch ......... 138
4.12.5 Changing time switch channel..................................................... 139
4.12.6 Entry rules.................................................................................... 140
4.12.7 Function of the year time switch ................................................. 142
4.12.8 Year time switch for sample parameter configurations ............... 142
4.13 Master Reset ............................................................................... 147
4.13.1 Operating modes ......................................................................... 148
4.13.2 Function of the master reset function relay................................. 148
4.14 Basic circuits ................................................................................ 149
4.14.1 Negation (contact)........................................................................ 149
4.14.2 Negation (coil) .............................................................................. 149
4.14.3 Permanent contact....................................................................... 149
4.14.4 Series circuit................................................................................. 150
4.14.5 Parallel connection ....................................................................... 150
4.14.6 Parallel circuit operating like a series connection of make
contacts........................................................................................ 151
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 3
4.14.7 Parallel circuit operating like a series connection of break
contacts ....................................................................................... 152
4.14.8 Two way switch........................................................................... 152
4.14.9 Self maintaining ........................................................................... 153
4.14.10 Impulse relays.............................................................................. 154
4.14.11 Cycle pulse on rising edge........................................................... 154
4.14.12 Cycle pulse on falling edge .......................................................... 154
4.15 Circuit examples .......................................................................... 155
4.15.1 Star-delta starting......................................................................... 155
4.15.2 4x shift register............................................................................ 156
4.15.3 Running light................................................................................ 159
4.15.4 Stairwell lighting........................................................................... 160
5 settings................................................................................ 163
5.1 Password protection.................................................................... 163
5.1.1 Password setup ........................................................................... 164
5.1.2 Selecting the scope of the password .......................................... 164
5.1.3 Activating Passwords................................................................... 165
5.1.4 unlocking.............................................................................. 165
5.1.5 Changing or deleting the password range ................................... 166
5.1.6 Password incorrect or no longer known ...................................... 167
5.2 Changing the menu language ...................................................... 167
5.3 Alter parameters .......................................................................... 168
5.3.1 Adjustable parameters for function relays ................................... 169
5.4 Setting date and time................................................................... 170
5.4.1 Set time ....................................................................................... 170
5.4.2 Setting summer time start and end............................................. 171
5.4.3 Setting summer time start and end............................................. 172
5.4.4 Summer time start and end, setting the rule............................... 172
5.5 Activating input delay (debounce)................................................ 176
5.5.1 Activating debounce (input delay)................................................ 176
5.5.2 Deactivating debounce (input delay)............................................ 177
5.6 Activating and deactivating the P buttons.................................... 177
5.6.1 Activating P buttons..................................................................... 177
5.6.2 Function of the P buttons ............................................................ 178
5.6.3 Deactivating the P buttons........................................................... 178
5.7 Startup behavior........................................................................... 178
5.7.1 Setting the startup behavior......................................................... 178
5.7.2 Behavior when the circuit diagram is deleted.............................. 179
5.7.3 Behavior during upload/download to card or PC.......................... 179
5.7.4 Possible Faults............................................................................. 179
5.7.5 Card startup behavior................................................................... 180
5.8 Setting the cycle time.................................................................. 181
5.9 Retention (non-volatile data storage) ........................................... 181
5.9.1 Permissible markers and function relays ..................................... 182
5.9.2 Setting retentive behavior............................................................ 182
5.9.3 Deleting retentive actual values................................................... 183
4 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
5.9.4 Transferring retentive behavior .................................................... 183
5.9.5 Changing the operating mode or the circuit diagram ................... 183
5.9.6 Changing the startup behavior in the SYSTEM menu.................. 184
5.10 Displaying device information ...................................................... 185
6 Internal................................................................................ 187
6.1 circuit diagram cycle............................................................. 187
6.1.1 operation and effects on circuit diagram creation ................. 188
6.2 Delay times for inputs and outputs .............................................. 189
6.2.1 Delay times with -DA and -DC basic units...................... 189
6.2.2 Delay time with -AB, -AC basic units.............................. 190
6.2.3 Delay times for the analog inputs of -AB, -DA and
-DC ........................................................................................ 191
6.3 Monitoring of the functionality of the basic unit .......................... 192
6.4 Monitoring of short-circuit/overload with EASY..-D.-T.................. 192
6.5 700 expanding....................................................................... 193
6.5.1 How is an expansion unit recognized?......................................... 193
6.5.2 Transfer behavior ......................................................................... 194
6.5.3 Function monitoring of expansion units....................................... 194
6.6 Saving and loading circuit diagrams ............................................. 195
6.6.1 EASY…-..-..X ................................................................................ 195
6.6.2 Interface ....................................................................................... 196
6.7 Memory card................................................................................ 197
6.7.1 Compatibility with EASY-M-8K, EASY-M-16K memory cards ...... 197
6.7.2 Loading or saving circuit diagrams ............................................... 198
6.8 Soft........................................................................................ 200
6.8.1 Program transfer between Soft and 500/700................. 200
6.8.2 Soft help................................................................................ 201
6.9 with a remote display and operator unit............................... 202
6.10 Device version.............................................................................. 202
7 What Happens If …? .................................................................. 203
7.1 Messages from the system .................................................. 203
7.2 Possible situations when creating circuit diagrams ..................... 204
7.3 Event ............................................................................................ 205
8 Appendix..................................................................................... 207
8.1 Approval and Certification ............................................................ 207
8.1.1 Approvals and national approvals for 500/700 devices ......... 207
8.1.2 Shipping approvals for 500/700 devices................................ 207
8.1.3 Approvals and national approvals for expansion devices ............. 208
8.1.4 Shipping approvals for expansion units 6.............................. 208
8.2 Dimensions .................................................................................. 208
8.3 Technical data .............................................................................. 210
8.3.1 Standards ..................................................................................... 210
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 5
8.3.2 General ........................................................................................ 210
8.3.3 Power supply ............................................................................... 212
8.3.4 Digital inputs ................................................................................ 213
8.3.5 Rapid counter inputs.................................................................... 217
8.3.6 Analog inputs ............................................................................... 217
8.3.7 Relay outputs............................................................................... 218
8.3.8 Transistor outputs........................................................................ 220
8.4 List of the function relays ............................................................ 222
8.4.1 Usable contacts ........................................................................... 222
8.4.2 Available function relays .............................................................. 223
8.4.3 Names of relays........................................................................... 223
8.4.4 Names of function relay............................................................... 224
8.4.5 Name of function block inputs (constants, operands).................. 224
8.5 Compatibility of the function relay parameters ............................ 224
8.5.1 Parameter display of analog value comparator ............................ 224
8.5.2 Parameter display of counters ..................................................... 225
8.5.3 Parameter display of weekly timer .............................................. 225
8.5.4 Parameter display of timing relay................................................. 225
8.5.5 Compatibility of memory cards.................................................... 225
9 Glossary of terms....................................................................... 227
6 Operating instructions 05/10 MN05013003Z-EN www.eaton.com

0 About This Manual

0.1 List of revisions

0 About This Manual
0.1 List of revisions
This manual describes the installation, commissioning and programming (circuit diagram generation) of the easy500 and easy700 control relay.
Specialist electrical training is needed for commissioning and creating circuit diagrams. When active components such as motors or pressure cylinders are controlled, parts of the system can be damaged and persons put at risk if the MFD device is connected or programmed incorrectly.
The following are the main changes and amendments which have been made since the edition 08/04 and 01/05 of this manual:

0.2 Device designation

Publication date
05/10 29 Hazard warning about the correct connection of the L
Page Subject New Modifi-
cation
✓
main pole and N neutral conductor
127 Timing relay - Signal Diagrams in fig. 64 + 68 ✓
127 Timing relay - Retriggering during response delay ✓
137 year time switch - additional examples ✓
194 Times of the timeout watchdogs, system control ✓
225 „Compatibility of memory cards“ ✓
This manual uses the following abbreviated designations for different device models:
Designation Device types
easy500 EASY512-AB...
EASY512-AC... EASY512-DA... EASY512-DC...
easy700
easy-AB
easy-AC
easy-DA
EASY719-AB... EASY719-AC... EASY719-DA... EASY719-DC... EASY721-DC...
EASY512-AB... EASY719-AB...
EASY512-AC... EASY618-AC-RE EASY719-AC..
EASY512-DA... EASY719-DA...
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 7
0 About This Manual

0.3 Writing conventions

Designation Device types
0.3 Writing conventions
easy-DC EASY512-DC...
easy-E
EASY512-..-... EASY7..-..-... Type designation of the control relay, the dots represent placeholders for all
Symbols used in this manual have the following meanings:
▶ indicates actions to be taken.
CAUTION
Warns about the possibility of material damage.
WARNING
EASY6..-DC... EASY719-DC... EASY721-DC...
EASY2.. EASY618-AC-RE EASY618-DC-RE EASY620-DC-TE
characters used
 
￫
For greater clarity, the name of the current chapter is shown in the 1. headline and the name of the current section in the 2. headline.
Warns of the possibility of hazardous situations that may possibly cause injury.
WARNING
Warns of the possibility of hazardous situations that could result in serious injury or even death.
DANGER
Warns of hazardous situations that result in serious injury or death.
Draws your attention to interesting tips and supplementary information.
8 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1

1.1 Target group

1.2 Proper use

1 
1.1 Target group
easy must only be installed and connected up by trained electricians or other persons who are familiar with the installation of electrical equipment.
Specialist electrical training is needed for commissioning and creating circuit diagrams. When active components such as motors or pressure cylinders are controlled, parts of the system can be damaged and persons put at risk if the MFD device is connected or programmed incorrectly.
easy is a programmable switching and controlgear and is used as a replacement for relay and contactor control circuits. easy may only be operated when it has been correctly and properly installed.
• easy is designed to be installed in an enclosure, switch cabinet or service
distribution board. Both the power supply and the signal terminals must be laid and covered so as to prevent accidental contact.
• The installation must comply with regulations for electromagnetic
compatibility EMC.
• The power up of easy must not cause any hazards arising from activated
devices, such as unexpected motor startups or power ups.

1.2.1 Improper use

easy should not be used as a substitute for safety-related controls such as burner or crane controls, emergency-stop or two-hand safety controls.
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 9
1 
POW
BUS
POWER
COM-ERR
ADR
ERR
MS
NS
4
3
3
2
2
1
1
5
6
7
8
12
11
11
9
10
10

1.3 Over view

1.3 Overview
Figure 1: easy basic units and expansion devices
10 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1 
1.3 Over view
Legend for figure 1:
a easy500 basic unit b easy700 basic device with EASY-LINK-DS data connector c Detachable text display consists of MFD-80(-B) and MFD(-AC)-CP4-500 d EASY209-SE ethernet gateway, connection via the serial multi-function interface e EASY204-DP PROFIBUS-DP slave gateway f EASY205-ASI AS-Interface slave gateway g EASY221-CO CANopen gateway h EASY222-DN DeviceNet gateway i EASY202-RE output expansion j I/O expansion EASY410-DC-… k I/O expansion EASY6..-…-.E l EASY200-EASY coupling device
easy is an electronic control relay with logic functions, timer, counter and time switch functions. It is also a control and input device in one, that can perform many different tasks in domestic applications as well as in machine building and plant construction.
easy ensures correct functioning at the start and during operation by executing internal tests and with the help of various timeout watchdogs, (￫ Table 34:, Page 192).
Circuit diagrams are connected up using ladder diagrams. and each element is entered directly via the easy display. You can:
• Connect N/O and N/C contacts in series and in parallel
• switch output relays and auxiliary relays,
• Use outputs as relays, impulse relays or latching relays,
• Use multi-function timing relays with different functions,
• Use up and down counters,
• Count high-speed counter pulses,
• Measure frequencies,
• Process analog inputs, easy-AB, easy-DA, easy-DC, (EASY512…: two
analog inputs, easy700: four analog inputs),
• Display any texts with variables, enter setpoints,
• Use year time switches, weekly timer, EASY…-…-.C(X),
• Count operating hours (four retentive operating hours counters are
integrated),
• trace the power flow in the circuit diagram,
• load, store and password protect a circuit diagram.
If you wish to wire easy via your PC, use the easySoft-Basic or easySoft-Pro programming software. easySoft allows you to create and test your program (circuit diagram) on the PC. It also allows you to print out your circuit diagram in DIN/IEC, ANSI/CSA or easy format.
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 11
1 
DEL
ALT
ESC
OK
햳
햲
햸
햷
ESC
OK
DEL
ALT
햵
햴
햶

1.4 Versions

1.4 Versions
easy basic units at a glance
Figure 2: Versions
a Supply voltage connection b Inputs c Status LED d Keypad e Interface socket for memory card or PC connection f Outputs g Display
12 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1.4 Versions
easy basic units with stand-alone MFD-80…, MFD-CP4-500 HMI unit
1 
1
3
4
3
2
Figure 3: Overview with stand-alone HMI unit
a easy500 basic units b easy700 basic units c Display/operating unit MFD-80(-B) d Power supply/communication module with MFD(-AC)-CP4-500 interface cable
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 13
1 
1.4 Versions

1.4.1 Key to part numbers

EASY - x x x - x x - x x x
LCD display: X = No display Time switch: C = Available; E = Expansion
Output type: R = Relay (max. 8 A) T = Transistor (0.5 A, parallel connection possible up to 2 A)
Supply voltage, device and inputs AB = 24 V AC (2, (4) inputs, also usable as 0 to 10 V analog inputs) AC = 100, 120, 230, 240 V AC DC = 24 V DC (2 (4) inputs, also usable as 0 to 10 V analog inputs) DA = 12 V DC (2 (4) inputs, also usable as 0 to 10 V analog inputs)
Number of inputs/outputs (+ expansion) 12 = 8 I/4 O 18 = 12 I/6 O 19 = 12 I/6 O + expansion 20 = 12 I/8 O 21 = 12 I/8 O + expansion
Rating class (RC) and space unit (SU) 2 = 35.5 mm (SU) 4, 5 = 71.5 mm (4 SU), RC = 4 or 5 6, 7= 107.5 mm (6SU), RC = 6 or 7
Control relays easy
Table 1: Overview of comparable easy400 types with easy500 and easy600 with easy700
easy400, easy600 easy500, easy700
–
–
EASY412-AC-R
EASY412-AC-RC
EASY412-AC-RCX
EASY412-DA-RC
EASY412-DA-RCX
EASY412-DC-R
EASY412-DC-RC
EASY412-DC-RCX
EASY412-DC-TC
EASY412-DC-TCX
–
–
EASY619-AC-RC
EASY619-AC-RCX
–
–
EASY619-DC-RC
EASY619-DC-RCX
EASY621-DC-TC
EASY621-DC-TCX
EASY512-AB-RC
EASY512-AB-RCX
EASY512-AC-R
EASY512-AC-RC
EASY512-AC-RCX
EASY512-DA-RC
EASY512-DA-RCX
EASY512-DC-R
EASY512-DC-RC
EASY512-DC-RCX
EASY512-DC-TC
EASY512-DC-TCX
EASY719-AB-RC
EASY719-AB-RCX
EASY719-AC-RC
EASY719-AC-RCX
EASY719-DA-RC
EASY719-DA-RCX
EASY719-DC-RC
EASY719-DC-RCX
EASY721-DC-TC
EASY721-DC-TCX
14 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1.5 operating principles
ALT
DELDELDELDELDELDELDELDELDELDEL
ESC
OK

1.5.1 Key Pad

DEL: Delete object in circuit diagram ALT: Special functions in circuit diagram, Status display Cursor buttons
Move cursor Select menu items Set contact numbers, contacts and values
OK: Next menu level, Save your entry ESC: Previous menu level, Cancel

1.5.2 Selecting menus and entering values

Calling the System menu
and
Move to next menu level Call menu item Activate, change, store entries
Move to previous menu level Cancel entries since last OK
1 
1.5 operating principles
úí ÍÚ:
ÍÚ
Change menu item Change value
úí
Change place
P button function:
ú í
Input P1, Input P3,
Í Ú
Input P2 Input P4
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 15
1 
1.2 RS MO .2…6..
I ..2..5...
P­MO 02:00 ..34…. RUN
and
No password
PROGRAM...
STOPå RUN PARAMETER INFO... SET CLOCK
SECURITY…
SYSTEM... LANGUAGE...
easy500: 8 inputs, 4 outputs
Current selection
flashes in the
easy menu
Clock menu on
devices with clock
1st menu level
Main menu
1. Menu mode
System menu easy500 or easy700
SECURITY… SYSTEM... LANGUAGE... CONFIGURATOR
The CONFIGURATOR menu appears if a configurable expansion module is connected such as EASY204­DP (Profibus-DP bus gateway)
.2..5.......
P-
MO 11:50
..34 RUN
.2..5.......
P-
2010-04-01
34 RUN
1.5 operating principles

1.5.3 Choosing the main and system menu

1.5.3.1 Status indicator
1.5.3.2 Toggling between weekday, time display and date display
16 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
(only on devices with clock)
1.5.4 Status indicator
.2..5.......
P-
MO 11:50
Q ..34..STOP
.2..5.......
P-
2010-04-01
Q ..34..STOP
1.......9...
RS AC P­MO 10:42
1.....7. RUN
1.......9...
RS AC P­MO 10:42
1.....7. RUN
12...6.89... RE I AC P-
04.03.17 ST
123.5.78 RUN
Inputs
Weekday/Time or Weekday/Date
Outputs RUN/STOP mode

1.5.5 Status display for local expansion

On: 1, 2, 3, 4/Off:…
1 
1.5 operating principles
easy500: input 1 to 8, easy700: input 1 to 12
easy500: output 1 to 4, easy700: output 1 to 6 or 8

1.5.6 Advanced Status display

: Retention switched on
RE
: Debounce switched on
I
: AC expansion functioning correctly
AC
: DC expansion functioning correctly
DC
: Bus coupling module detected
GW
: When the power supply is switched on, easy switches to STOP mode
ST
Inputs
Expansion device
Weekday/Time or Weekday/Date
Outputs
On: 1, 2, 3, 4/Off:…
RS = Expansion functioning correctly
Retention/debounce AC expansion ok/P buttons
Start behavior
GW flashes: Only easy200-easy detected. I/O expansion not detected.
04.03.17 Display of actual device date
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 17
1 
PROGRAM...Æ
STOP å RUN PARAMETER INFO... æ SET CLOCK..
PROGRAM...
DELETE PROG MODE
SAVE
CANCEL
Main menu
STOP: Circuit diagram display
Parameters
Circuit Diagram
Parameter display
DELETE ?
PROGRAM...
DELETE PROG
CARD...
DEVICE-CARD
CARD-DEVICE DELETE CARD
REPLACE ?
PROGRAM... DELETE PROG
CARD...
DEVICE-CARD
CARD-DEVICE
DELETE CARD
DELETE ?
DEVICE-CARD CARD-DEVICE
DELETE CARD
The arrows indicate that there are more than four menus.
REPLACE ?
1.5 operating principles
1.5.7 LED display
EASY512-…-…X, easy700 and easy-E feature an LED on the front indicating the status of the power supply as well as whether RUN or STOP mode is active (￫, page12).
LED OFF No supply voltage
LED continuously lit Power supply present, STOP mode
LED flashing Power supply present, RUN mode

1.5.8 Menu structure

1.5.8.1 Main menu without password protection
▶ You access the main menu by pressing OK.
18 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1 
PROGRAM...Æ
STOP RUN å
PARAMETER INFO... æ SET CLOCK..
Main menu
Parameter display
SET CLOCK..
SUMMER TIME...
PROGRAM...
Æ
STOP RUN
å
PARAMETER...
INFO...
æ
PROGRAM... STOP RUN
Æ
PARAMETER INFO...
SET CLOCK.
æ
Display for date and time setting
HH:MM --:-- TT.MM --.--
YEAR ____
HH:MM 14:23 TT.MM 17.03 YEAR 2010
T1 X S + T2 Ü M:S + C1 N + O1 +
T1 X S + S1 10.000 S2 +0
T:
Information display of the device
PROGRAM...
Æ
STOP RUN
å
PARAMETER...
INFO...
æ
SET CLOCK..
DC TC LCD OS: 1.00.027 CRC: 02752
1.5 operating principles
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 19
1 
AM --
Æ
WD: --
--
TT.MM:00.00
æ
HH:MM:00:00 DIFF: 00:00
NONE
Æ
RULE...
å
EU GB
æ
US
NONE
Æ
RULE...
EU GB
æ
US
AM --
Æ
WD: --
--
TT.MM:00.00
æ
HH:MM:00:00 DIFF: 00:00
Main menu
PROGRAM... STOP RUN
Æ
PARAMETER.. INFO...
SET CLOCK.
æ
SET CLOCK..
SUMMER TIME…
Only one selection is possible.
NONE
åÆ
RULE... EU GB
æ
US
SUMMER START SUMMER END
SUMMER START
SUMMER END
SET CLOCK..
SUMMER TIME…
NONE
Æ
RULE...
å
EU GB
æ
US
SUMMER START SUMMER END
SET CLOCK..
SUMMER TIME…
SET CLOCK..
SUMMER TIME…
1.5 operating principles
20 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
1.5.8.2 Main menu with password protection
PASSWORD..
Æ
STOP RUN
å
PARAMETER... INFO...
æ
SET CLOCK..
Password
Password entryUnlocking
easy
Main menu
PASSWORD...
STOP RUN
å
DELETE ?
Correct entry
Status indicator
four wrong entries (if enabled)
Example:
Password only on program
PROGRAM
åÆ
PARAMETER
å
CLOCK
å
OPRTNG MODEæ
INTERFACE.
å
DEL PROG
å
PROGRAM å
Æ
PARAMETER CLOCK OPRTNG MODE
æ
INTERFACE DEL PROG
ENTER PASSW..
XXXX
System menu
ACTIVATE PW
CHANGE PW
Password entry
Change/ delete password
SECURITY…
SYSTEM... LANGUAGE... CONFIGURATOR
Password setup
PASSWORD...
RANGE...
ENTER PASSW..
XXXX
CHANGE PW
ACTIVATE PW
CHANGE PW
ACTIVATE PW
PASSWORD...
RANGE...
1.5.8.3 System menu
The System menu is accessed by simultaneously pressing DEL and ALT.
1 
1.5 operating principles
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 21
1 
ENGLISH
Æ
DEUTSCH
å
FRANCAIS ESPANOL
æ
ITALIANO PORTUGUES NEDERLANDS SVENSKA POLSKI TURKCE CESKY MAGYAR
System menu
SECURITY… SYSTEM...
LANGUAGE...
CONFIGURATOR
SECURITY… SYSTEM... LANGUAGE...
CONFIGURATOR
The further menus depend on the connected expansion device.
Only one selection is possible.
SECURITY…
SYSTEM...
LANGUAGE... CONFIGURATOR
DEBOUNCE.
å
P BUTTONS RUN MODE
å
CARD MODE CYCLE-T... RETENTION
PROGRAM... STOP
PARAMETER
INFO
HH:MM â4:23 TT.MM 17.03 YEAR 2010
HH:MM 14:23 TT.MM 17.03 YEAR 2010
1.5 operating principles

1.5.9 Selecting or toggling between menu items

1.5.10 Cursor display

22 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
Cursor Í Ú
Select or toggle
The cursor flashes.
Full cursor
• Move cursor with
Ê/:
ú í,
• in circuit diagram also with Í
Ú
Value M/M
• Change position with ú í
• Change values with Í Ú
Flashing values/menus are shown in grey in this manual.

1.5.11 Set value

HH:MM 14:23 TT.MM 17.03 YEAR 2010
Values
Digits
Current value at the position
(can be changed, Cursor = 3)
1 
1.5 operating principles
Select value Í Ú Select digit ú í Change value at digit Í Ú
Store entries
Retain previous value
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 23
1 
1.5 operating principles
24 Operating instructions 05/10 MN05013003Z-EN www.eaton.com

2 Installation

2 Installation
easy must only be installed and wired up by trained electricians or other persons familiar with the installation of electrical equipment.
DANGER
easy is installed in the following order:
• Assemble devices if necessary,
• Mounting,
• Wiring up the inputs,
• Wiring up the outputs,
• Connecting the power supply.
Never carry out electrical work on the device while the power supply is switched on, there is danger of electric shock. Always follow the safety rules:
• Switch off and isolate
• Secure against retriggering.
• Verify isolation from the supply.
• Cover adjacent live parts.
Operating instructions 05/10 MN05013003Z-EN www.eaton.com 25
2 Installation
30 mm
(1.18“)
30 mm
(1.18“)
30 mm
(1.18“)
30 mm
(1.18“)
1
2

2.1 Mounting

2.1 Mounting
Install the easy in a control cabinet, service distribution board or in an enclosure so that the power supply and terminal connections cannot be touched accidentally during operation.
Clip easy onto a DIN EN 50022 top-hat rail or fix easy in place using fixing brackets. easy can be mounted vertically or horizontally.
￫
For ease of wiring, leave a gap of at least 30 mm between easy terminals and the wall or adjacent devices.
Figure 4: Clearances to easy

2.1.1 Mounting on top-hat rail

▶ Hook easy to the top edge of the top-hat rail and hinge into place while
Easy will clip into place and will be secured by the built-in spring mechanism.
When using easy with expansion units, connect the expansion concerned before mounting (￫ section “2.2 Connecting the expansion device”, page 28).
pressing down slightly. Press down lightly on both the device and the top-hat rail until the unit snaps over the lower edge of the top-hat rail.
▶ Check that the device is seated firmly. The device is mounted vertically on a top-hat rail in the same way.
26 Operating instructions 05/10 MN05013003Z-EN www.eaton.com
Loading...
+ 210 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use