Eaton DT400, DT436 Installation Instructions Manual
Lorem ipsum dolor sit Amat
Connectors and Splices
MN650001EN
Effective September 2014
Supersedes IS550-30-1 March 2011
DT400/436 Tee Connector Installation Instructions
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
The information, recommendations, descriptions and safety notations in this document are based on Eaton Corporation’s
(“Eaton”) experience and judgment and may not cover all contingencies. If further information is required, an Eaton sales
office should be consulted. Sale of the product shown in this literature is subject to the terms and conditions outlined in
appropriate Eaton selling policies or other contractual agreement between Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE
SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE
ENTIRE OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY
ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or
other-wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to
damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the
use of existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the
information, recommendations and descriptions contained herein. The information contained in this manual is subject to
change without notice.
ii
DT400/436 tee connector installation instructions MN650001EN September 2014 www.cooperpower.com
Contents
SAFETY INFORMATION
Safety Information ..........................................................................iv
PRODUCT INFORMATION
Introduction ............................................................................... 1
Acceptance and Initial Inspection............................................................... 1
Handling and Storage ........................................................................ 1
Standards ................................................................................. 1
INSTALLATION PROCEDURE
Installation Instructions ...................................................................... 2
iii
DT400/436 tee connector installation instructions MN650001EN September 2014 www.cooperpower.com
The instructions in this manual are not intended as a
substitute for proper training or adequate experience
in the safe operation of the equipment described.
Only competent technicians who are familiar with this
equipment should install, operate, and service it.
A competent technician has these qualifications:
• Is thoroughly familiar with these instructions.
• Is trained in industry-accepted high and low-voltage safe
operating practices and procedures.
• Is trained and authorized to energize, de-energize, clear,
and ground power distribution equipment.
• Is trained in the care and use of protective equipment
such as arc flash clothing, safety glasses, face shield,
hard hat, rubber gloves, clampstick, hotstick, etc.
Following is important safety information. For safe
installation and operation of this equipment, be sure to
read and understand all cautions and warnings.
Safety instructions
Following are general caution and warning statements
that apply to this equipment. Additional statements, related to specific tasks and procedures, are located throughout the manual.
Safety for life
!
SAFETY
FOR LIFE
!
SAFETY
FOR LIFE
Eaton’s Cooper Power Systems products meet or exceed all applicable industry standards relating to product safety. We
actively promote safe practices in the use and maintenance of our products through our service literature, instructional
training programs, and the continuous efforts of all Eaton’s Cooper Power Systems employees involved in product
design, manufacture, marketing, and service.
We strongly urge that you always follow all locally approved safety procedures and safety instructions when working
around high voltage lines and equipment, and support our “Safety For Life” mission.
Safety information
DANGER
Hazardous voltage. Contact with hazardous voltage
will cause death or severe personal injury. Follow all
locally approved safety procedures when working
around high- and low-voltage lines and equipment.
G103.3
This manual may contain four types of hazard
statements:
DANGER
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in equipment
damage only.
Hazard Statement Definitions
WARNING
Before installing, operating, maintaining, or testing
this equipment, carefully read and understand the
contents of this manual. Improper operation, handling
or maintenance can result in death, severe personal
injury, and equipment damage.
G101.0
WARNING
This equipment is not intended to protect human
life. Follow all locally approved procedures and safety
practices when installing or operating this equipment.
Failure to comply can result in death, severe personal
injury and equipment damage.
G102.1
WARNING
Power distribution and transmission equipment must
be properly selected for the intended application. It
must be installed and serviced by competent personnel
who have been trained and understand proper safety
procedures. These instructions are written for such
personnel and are not a substitute for adequate
training and experience in safety procedures. Failure to
properly select, install or maintain power distribution
and transmission equipment can result in death, severe
personal injury, and equipment damage.
G122.3
iv
DT400/436 tee connector installation instructions MN650001EN September 2014 www.cooperpower.com
Loading...