Eaton AtLite Sure-Lites SELDWA29SD, AtLite Sure-Lites ATLELDWA100SD Installation Instructions Manual
AtLite
Sure-Lites
Installation Instructions for the Sure-Lites SELDWA29SD/ATLELDWA100SD
Emergency Light with Self Diagnostics
WARNING
Risk of Fire / Electric Shock
If not qualifi ed, consult an electrician.
Important Safeguards
When using electrical equipment, basic safety precautions
should always be observed including the following:
• READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use in hazardous locations, or near gas or elec-
tric heaters.
• Do not let power supply cords touch hot surfaces.
• Use caution when servicing batteries. Battery acid can
cause burns to skin and eyes. If acid is spilled on skin
or in eyes, fl ush acid with fresh water and contact a
physician immediately.
• Do not use this equipment for other than the intended
use.
• Installation is to be performed only by qualifi ed personnel.
• Install in accordance with National Electric Code and
local regulatory agency requirements.
• The use of accessory equipment not recommended by
the manufacturer may cause an unsafe condition.
• Equipment should be mounted in locations and at
heights where it will not readily be subjected to tampering by unauthorized personnel.
• SAVE THESE INSTRUCTIONS
Maximum Mounting Height: 8.6 ft.
WARNING
Risk of Electric Shock
Disconnect power at fuse or circuit breaker before installing
or servicing.
INSTALLATION
1. De-energize the circuit at the junction box (J-box)
where the emergency light is to be installed.
2. Open the emergency light by inserting a fl at screw-
driver in the two slots on the side of the unit, then
turning to separate housing from the backplate.
3. To mount to a junction box mounting pattern and the wire pass hole in the backplate and the back gasket to fi t the J-box being used.
4. To mount to conduit – Unscrew the ½” NPT plug located at the top of the fi xture and screw in the user-sup-
plied conduit hub.
5. Once the backplate is secured, the housing can be
held in place during installation with the help of the
grounding wire
6. Connect the incoming wires to the SELDWA29SD/
ATLELDWA100SD power supply wires using the wire
nuts provided.
housing.
connect the black wire to the hot lead. If using 277V,
connect the orange wire to the hot lead. Cap the unused
lead. Secure the emergency light to the wall and/or
junction box using installer supplied hardware.
7. Complete the battery connection and snap the cover
onto the backplate.
8. Energize AC supply. The test button should illuminate,
and LED heads will illuminate briefl y when the test
button is pushed.
9. Adjust the heads as needed. The SELDWA29SD/
ATLELDWA100SD lenses utilize a highly directional beam,
and the lenses can be rotated to adjust the beams to the
front or sides of the fixture (see Fig. 2 next page).
(see Fig. 1 next page).
Connect the green grounding wire for the
Connect the white wire to neutral. If using 120V,
Knock out/drill out
the appropriate
ACTIVATING TIME DELAY
OPERATION
The SELDWA29SD/ATLELDWA100SD has an integrated
time delay circuit that allows them to remain in emergency
mode 15 minutes after power is restored.
To activate the time delay, remove the jumper on the circuit
board labeled TDI/J1.
Figure 1
Green(Grounding wire)
Figure 2
The Sure-Lites Eagle Eye Self Diagnostics is continuously monitoring your emergency fi xture, and will signal any
failure through the 3 color indicator LED.
INITIAL OPERATION
When the unit is fi rst powered up, it will go into a 24 hour
fast charge, indicated by the indicator LED pulsing green.
Once the unit has fully charged, it will perform a self calibration, after which the LED will change to steady green,
indicating the unit is fully charged and fl oat charging the
battery to maintain readiness.
AUTOMATIC TESTING
The unit will perform a battery capacity, lamp/LED, and
charge circuit test every 30 days for 30 seconds. During
this time, the indicator LED will change to a steady yellow.
It will perform a full battery capacity (90 minute) test once
per year. During this time, the indicator LED will change to
a blinking yellow.
MANUAL TESTING
• 10 Second “Installation” test – Press and release the
test button once during fast charge (blinking green) to
initiate a 10 second quick test. The sign will switch to
emergency mode for 10 seconds allowing the installer
to verify proper installation of the unit, and the LED
indicator will turn solid yellow.
• 30 Second Test - Press and release the test button
once during fl oat charge (steady green). The indica-
tor LED will turn steady yellow to indicate the unit is
performing a 30 second test of the batteries and lamps/
LEDs.
• 90 Minute Test - Press and release the test button a
second time during a 30 second test (steady yellow) to
change to a 90 minute test. During this test, the LED
indicator will change to blinking yellow, and the circuit
will perform a full battery capacity, charge circuit, and
LED test.
• Canceling Test – Press and release the test button
during the 90 minute test (fl ashing yellow) to return the
fi xture to its original state (fast charge or fl oat charge).
LASER TEST:
The SELDWA29SD/ATLELDWA100SD is equipped with a
Laser Test function, that allows the unit to be manually tested
without the need to physically press the test button. Shining a
laser pointer in the hole marked “LASER TEST” on the bottom
of the unit has the same effect as a press and release of the
test button.
Loading...