Eaton 5SC 1000i Rack2U, 5SC 2200i RT2U, 5SC 1500i Rack2U, 5SC 3000i RT2U Installation And User Manual
ENGLISH
Copyright © 2016 EATON
All rights reserved.
5SC 1 - 3 KVA US_EN
5SC 1000i Rack2U
5SC 1500i Rack2U
5SC 2200i RT2U
5SC 3000i RT2U
Installation and
user manual
Page 2
5SC 1 - 3 KVA US_EN
Page 3
5SC 1 - 3 KVA US_EN
ENGLISH
Certification Standards
Uninterruptible power systems (UPS) directives:
• IEC 62040-1: General and safety requirements for UPS
• IEC 62040-2: Electromagnetic compatibility (EMC) requirements
• IEC 62040-3: Method of specifying the performance and test requirements
• IEC 62040-4: Environmental aspects - Requirements and reporting
CE mark
CE compliance contact: Eaton I.F. – 110 rue Blaise Pascal – 38330 Montbonnot Saint Martin - France
The EC Declaration of Conformity is available upon request for products with a CE mark.
For copies of the EC Declaration of Conformity, contact Eaton Power Quality or check Eaton website:
www.powerquality.eaton.com
Class B emission level CISPR 22 (EN 55022)
Harmonics emission: IEC 61000-3-2
Flickers emission: IEC 61000-3-3
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.
Important instructions that must always be followed.
Do not discard the UPS or the UPS batteries in the trash.
This product contains sealed lead acid batteries and must be disposed as it's explain in this manual.
For more information, contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the
trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
Information, advice, help.
Page 4
5SC 1 - 3 KVA US_EN
Safety of Persons
• The system has its own power source (the battery). Consequently, the power outlets may be energized
even if the systems is disconnected from the AC power source.
• Dangerous voltage levels are present within the system. It should be opened exclusively by qualified
service personnel.
• The system must be connected to an earthed outlet.
• The battery supplied with the system contains small amounts of toxic materials.
To avoid accidents, the directives listed below must be observed:
- servicing of batteries should be performed or supervised by personnel knowledgeable about batteries
and the required precautions.
- when replacing batteries, replace with the same type and number of batteries or battery packs.
- do not dispose of batteries in a fire. The batteries may explode.
- batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high.
Precautions must be taken for all handling:
• Wear rubber gloves and boots.
• Do not lay tools or metal parts on top of batteries.
• Disconnect charging source prior to connecting or disconnecting battery terminals.
Product Safety
• The UPS connection instructions and operation described in the manual must be followed in the indicated
order.
• A protection circuit breaker must be installed upstream and be easily accessible.
The system can be disconnected from the AC power source by opening this circuit breaker or unplugging
the input cable.
• Check that the indications on the rating plate correspond to your AC powered system and to the actual
electrical consumption of all the equipment to be connected to the system.
• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily
accessible.
• Never install the system near liquids or in an excessively damp environment.
• Never let a foreign body penetrate inside the system.
• Never block the ventilation grates of the system.
• Never expose the system to direct sunlight or source of heat.
• If the system must be stored prior to installation, storage must be in a dry place.
• The admissible storage temperature range is -15 to +50 ºC / 5 to 122 ºF.
• The system is not for use in a computer room.
Special Precautions
• All handling operations will require at least two people (unpacking, installation in rack system).
• Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be
energized for a period of 24 hours, at least once every 6 months (for a normal storage temperature less
than 25 °C / 77 °F). This charges the battery, thus avoiding possible irreversible damage.
• During the replacement of the Battery Module, it is imperative to use the same type and number of element
as the original Battery Module provided with the UPS to maintain an identical level of performance and
safety. In case of doubt, don’t hesitate to contact your EATON representative.
Page 5
5SC 1 - 3 KVA US_EN
ENGLISH
Contents
1. Introduction ....................................................................................... 6
1.1 Environmental protection ...................................................................................................6
2. Presentation ...................................................................................... 7
2.1 Standard installations ........................................................................................................7
2.2 Rear panels ........................................................................................................................8
2.3 Control panel .....................................................................................................................9
2.4 LCD description .................................................................................................................9
2.5 UPS setting through the LCD ............................................................................................9
3. Installation ...................................................................................... 10
3.1 Unpacking and contents check ........................................................................................ 10
3.2 Installation of tower models ............................................................................................ 11
3.3 Installation of rack models ............................................................................................... 11
3.4 Wall mounting of rack models .........................................................................................13
3.5 Communication ports ...................................................................................................... 14
3.6 UPS remote control functions ......................................................................................... 15
4. Operation ......................................................................................... 16
4.1 Start-up and Normal operation......................................................................................... 16
4.2 Starting the UPS on Battery ............................................................................................16
4.3 UPS Shutdown ................................................................................................................16
4.4 Operation on Battery Power ............................................................................................ 16
4.5 Return of AC Input Power ................................................................................................ 16
5. Maintenance.................................................................................... 17
5.1 Troubleshooting ................................................................................................................ 17
5.2 Battery-module replacement ...........................................................................................18
6. Appendices ...................................................................................... 19
6.1 Technical specications .................................................................................................... 19
6.2 Glossary ...........................................................................................................................20
Page 6
5SC 1 - 3 KVA US_EN
1. Introduction
Thank you for selecting an EATON product to protect your electrical equipment.
The 5SC range has been designed with the utmost care.
We recommend that you take the time to read this manual to take full advantage of the many features of your
UPS (Uninterruptible Power System).
Before installing 5SC, please read the booklet presenting the safety instructions. Then follow the indications
in this manual.
To discover the entire range of EATON products and the options available for the 5SC range, we invite you to
visit our web site at www.eaton.com/powerquality or contact your EATON representative.
1.1 Environmental protection
EATON has implemented an environmental-protection policy.
Products are developed according to an eco-design approach.
Substances
This product does not contain CFCs, HCFCs or asbestos.
Packing
To improve waste treatment and facilitate recycling, separate the various packing components.
• The cardboard we use comprises over 50 % of recycled cardboard.
• Sacks and bags are made of polyethylene.
• Packing materials are recyclable and bear the appropriate identification symbol
01
PET
Materials Abbreviations
Nu
m
ber in
01
PET
the symbols
Polyethylene terephthalat PET 01
High-density polyethylene HDPE 02
Polyvinyl chloride PVC 03
Low-density polyethylene LDPE 04
Polypropylene PP 05
Polystyrene PS 06
Follow all local regulations for the disposal of packing materials.
End of life
EATON will process products at the end of their service life in compliance with local regulations.
EATON works with companies in charge of collecting and eliminating our products at the end of their service
life.
Product
The product is made up of recyclable materials.
Dismantling and destruction must take place in compliance with all local regulations concerning waste.
At the end of its service life, the product must be transported to a processing centre for electrical and electronic
waste.
Battery
The product contains lead-acid batteries that must be processed according to applicable local regulations
concerning batteries.
The battery may be removed to comply with regulations and in view of correct disposal.
Loading...