EasyPix GoXtreme Race Mini Operating Instructions

ACTION CAMCORDER

Functions

Functions

This user's manual has referred to the latest information we had when this user’s manual was made. The screen
display and illustrations are used in this user's manual for the purpose of introducing details of this digital camera

in a more specific and direct way. Difference may arise between these displays and illus trations and the digital
camera actually available for you due to difference in technological development and production batch, under

which case, the actual functions of this video camera shall prevail.

1

Announcements

Announcements

Please read the Announcements carefully before using this video camera for proper and safe operation, so as to
bring its optimum performance into play and extend its service life.

! Do not expose the video camera to sunshine directly, nor point its lens to sunlight. Otherwise, the image

sensor of the video camera may be damaged.

! Take good care of the video camera and prevent water or sand particles from entering the video camera

when it is used on the beach or water, because water, sand particles, dust or component containing salt may
damage the video camera.

! Keep the video camera contaminated free of dust and chemical materials. Place it in a cool, dry and well

ventilated place. Do not place the video camera in a high temperature, moist or dusty place.

! Please check if the video camera can operate normally before use.

! If dirt or stain is accu mulated on the video camera or on its lens, use soft, clean and dry rag to wipe it away

gently. If the video camera or its lens is stained with sand particles, blow them away gently. Do not use
cloth to wipe arbitrarily. Otherwise, it may scratch the surface of video camera or its lens.

! If it is required to clean camera surface, firstly blow away the sand dust accumulated on this surface, and

then wipe the camera gently with rag or tissue applicable to optical equipments.

2

Please use the cleaning agent of video camera for wiping if necessary. Do not use organic solvent to clean

the video camera.

! Do not touch the lens surface with fingers.

! Please back up the data if the memory card inside this video camera is used for the first time.

! The externally installed memory cards are manufactured from precise electronic components. Data may be

lost or damaged under the following circumstances:

1. Improper use of the memory card.

2. The memory card is bent, dropped or collided.

3. Place it under high temperature or moist environment or expose to sunshine directly.

4. Electrostatic or electromagnetic field exists around the memory card.

5. This memory card is taken out or power supply is interrupted when this video camera or computer is

connected to the memory card (i.e. during reading, writing and formatting).

6. Touch the metal contact surface of the memory card with fingers or metal materials.

3

Waterproof Case Using Notice

Waterproof Case Using Notice

! Before sealing the waterproof case, keep the camera housing’s rubber seal clean, a single hair or grain of

sand can cause a leak. You can test by closing the case without inserting the camera. Submerse the case

completely in water for about a minute. Remove the case from the water, dry off its exterior with a towel,
then open the case. If the entire interior is dry, the case is safe for use under water.

! Remember to put the Mode Switch in your desired recording position before inserting the camera in the

waterproof case. There is no external button for the Mode Switch.

! After every use in salt water you will need to rinse the outside of the housing with non-salt water and dry.

Not doing this can eventually cause corrosion of the hinge pin and salt buildup in the seal, which can cause
failure.

! To clean the seal, rinse in fresh water and shake dry (drying with a cloth may cause lint to compromise the

seal). Re-install the seal into the grooves in the backdoor of the housing.

4

System Requirements

System Requirements

System Requirements

Operating System

Microsoft Windows2000, XP, Vista, 7

CPU

Intel Pentium III of more than 800MHz or other CPU with
equivalent performance

Internal Memory

Larger than 512MB

Sound Card and
Display Card

The sound card and display card shall support DirectX8 or higher
version.

CD Driver

Speed of 4 times or faster

Hard Disk

Free space of more than 500MB

Others

One standard USB1.1 or USB2.0 port

5

Appearance and key introduction

Appearance and key introduction

Power
On/Off

Shutter
Charging indicator

Operation indicator

Up key

OK key

Down key

LCD TFT

Mode switch:

-Photograph

-Video

-Replay
Lens

6

Key/Indicator

Function

Power On/Off

Power the camera on or off. When opening the menu, switch over between normal

(effect parameters and replay of image, video) and setup menu.

Shutter

In recording video mode, it is used to start/stop recording. In capture mode, it is used

as a shutter. In replay mode; it is used to play the video. When operating the menu, it

is used to confirm the selection.

Up key

Digital zoom in (capture/video mode); menu selection (after opening the menu);

pause, continue playing (when playing and recording video in replay mode).

OK key

Open/exit from menu. Stop playing (when replaying video).

Down key

Digital zoom out (capture/video mode); menu selection (after opening the menu).

Mode switch

Switch over among modes of capture, video and replay.

Operation

indicator

The upper one is a charging

indicator.

In power-off state, it keeps constant lighting

when the charger is connected for charging.

The lower one is an operation

indicator.

It flashes once during capturing, and it keeps

constant lighting when connected with

computer portable disk.

7

Usage

Usage

1. Charge the built-in lithium battery

Connect the video camera with computer for charging in the shutdown state. The indicator light for

charging is on at this time and will be off after charging. In general, it can be fully charged after 2-4 hours.

USB Cable

Charger indicator lights

8

2. Use of Memory Card

1. Push the memory card into the card slot according to the concave lettering beside the slot of memory card

till it is completely inserted.

2. To take out the memory card, gently press the end of the memory card inward and it will pop up.

Note: No built-in memory is available in this video camera. Make sure to insert memory card before

using.

9

3. Startup/Shutdown

3.1 Startup: Press the POWER button for 3 seconds, the screen is displayed and the camera is on.

3.2. Shutdown: Press the POWER Key, and the camera will be shut down. .

Automatic shutdown: when the idle time of the video camera reaches the time for automatic shutdown, it
will be shut down automatically to save power. The default time of this camera for automatic shutdown is

5 minutes.

3.3. Shutdown in case of power shortage: when the power of the battery is insufficient, the LCD display screen
will display the low power icon. Please charge it in time. When indicate light turns red and flickering, the

video camera will be shut down automatically.