Eastern Times Technology DS 2669 Users manual

东莞市丰润计算机有限公司

Eastern Times Technology Co.ltd

地址:东莞市凤岗镇油甘铺村南岸工业园 D 栋

Factory location: Building D, Nan An Industry Park, Youganpu Village,

fenggangTown, dongguan City, Guangdong,China

Tel:0769-86800666 Ext:880 Fax:0769-86800338

M692

BLADE WIRELESS GAMING MOUSE

User Manual

Frequency Band： (2408-2474MHz) RF Output Power (ERP or EIRP) ：0

Installation:

1. Find the wireless mouse and Nano receiver in package

2. Plug Nano receiver to USB port on PC

3. 1PCS AA battery into Mouse body Properly

4. LED indicator will keep flash for few seconds, the Mouse is ready to work.

Advanced function

1. CPI adjustable function

With 6 adjustable CPI 1200CPI. Press the switch button CPI+ CPI- on top of Mouse can easy to adjust CPI. LED indicator will flash one time while it converting to 800CPI, LED will flash twice while it converting to 1200CPI, LED will flash three times while it converting to 1600CPI, LED will flash four times while it converting to 2400CPI, LED will flash five times while it converting to 3200CPI, LED will flash six times while it converting to 4800CPI.

2. Customized function for the fourth and fifth button There is two side key of mouse, it is default for move back/ move toward function. Two side buttons can be set for different functioins after install the software, please go through our website www.etpc.cn

3. Low power indicator for alarm to change new battery As the mouse working in a certain time, the battery will be out of power, low power indicator will be flash in red, to alarm you change new battery. （放图）

4. Saving power mode and power switch off If mouse is stay out of work for 8 minutes, it will turn to power saving mode,

press any button to restart it.

If you turn off PC or take out Nano receiver from USB port, press any button or move

800/1200/1600/2400/3200/4800 , factory setting is

dBm = 1 mW

to download the software.

the mouse to enter the power saving mode

5. Nano receiver

A very small size design for Nano receiver, it can be plug and stay on USB port

of PC/Notebook without interference.

Portable design for travel, Nano receiver can be plug in the slot on bottom of

mouse

6. Polling rate adjustable function

3 adjustable polling rate 125Hz/250Hz/500HZ, default as 125Hz

7. Buttons: Left key, right key, middle key, CPI+,CPI-, Home ,Two side

keys

Reconnection

Both of mouse and Nano receiver has a built-in code, It can be setting one mouse to one receiver, or few of mouse to one receiver. Mouse and receiver need to reconnect under the condition of High temperature, high magnetic, strong vibrate.

1. Plug off nano receiver from USB port, and plug it on

2. Keep the mouse in 50CM with receiver, re-store the battery

3. You can use it by reconnection

FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.