Page 1
Page 1
Boat Tent
SS143314 14’x33’x14’
W4.3xL10.0xH4.3m
Assembly Instructions
RECOMMENDED TOOLS
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE.
Before you start: 4+ individual recommended for assembly, approximate time 3 hr.
Page 2
Page 2
ATTENTION:
This shelter product is manufactured with quality materials. It is designed to fit our custom fabric cover included.
Our shelters offer storage and protection from damage caused by sun, light rain, tree sap, animal - bird excrement and light snow.
Please anchor this structure properly. See manual for more anchoring details. Proper anchoring, kee ping cover tight and free of
snow and debris is the responsibility of the consumer. Please read and understand the installation detail, warnings and cautions
prior to beginning installation. If you have any questions contact your local dealer.
DANGER:
Prior to installation, choose the location of your shelter carefully.
DANGER: Keep away from electrical wires.
Check for overhead utility lines, tree branches or other structures. Check for underground pipes or
wires before you dig. DO NOT install near roof lines or other structures that could shed snow,
ice or excessive run off onto your shelter. DO NOT hang objects from the roof or support cables.
WARNING:
Risk of fire. DO NOT smoke or use open flame devices (including grills, fire pits, deep fryers, smokers or
lanterns) in or around the shelter. DO NOT store flammable liquids (gasoline, kerosene, propane, etc.) in
or around your shelter. Do not expose top or sides of the shelter to open fire or other flame source.
CAUTION:
Use CAUTION when erecting the frame. Use safety goggles during installation. Secure and bolt together
overhead poles during assembly. Beware of pole ends.
PROPER ANCHORING AND INSTALLATION OF FRAME:
PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
We are not responsible for damage to the unit or the contents from acts of nature. Any shelter that is not anchored
securely has the potential to fly away causing damage, and is not covered under the warranty. Periodically check the anchors to
ensure stability of shelter. We cannot be responsible for any shelter that blows away.
NOTE:
Your shelter’s cover can be quickly removed and stored prior to severe weather conditions. If strong winds or severe
weather is forecast in your area, we recommend removal of cover.
CARE AND CLEANING:
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate
deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a
broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always
remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to
remove snow. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to
clean the fabric cover. Cover is easily cleaned with mild soap and water.
WARRANTY:
This shelter carries a full limited warranty against defects in workmanship. We warrant to the Original Purchaser that if
properly used and installed, the product and all associated parts, are free from manufacturer’s defects for a period of:
1 YEAR FOR COVER FABRIC, END PANELS AND FRAMEWORK
Page 3
Page 3
Boat Tent W4.3xL10.0xH4.3m Parts List
Part
Code
Description of Parts Qty(PC)
1 Roof Bent Joist
6
2
Sidewall Bent Joist for front
door (left)
1
3
Sidewall Bent Joist for front
door (right)
1
4
Sidewall Bent Joist for middle
arches (left)
5
5
Sidewall Bent Joist for middle
arches (right)
5
6 Roof Bracing Tube
6
7 Upright
8
8
Upright for Sidewall Bracing
Tube (No.10)
4
9 Purlin
25
10 Sidewall Bracing Tube
4
11 Four Corner Base Plate
4
12 Middle Base Plate
8
13 Lower Tensioning Tube
2
14 Door Bracing Tube
2
Page 4
Page 4
15 Deformed Bar Anchor
28
16 Roof Cover
1
17 Front Cover
1
18 Back Cover
1
19 Bolt M8x60
48
20 Bolt M8x70
24
21 Carriage Bolt M8x70
46
22 Self-drilling Screw for No.14
4
23 Knitting Rope for Front Door
2 bundles
24 Knitting Rope for Roof Cover
1 bundle
25 Cable Tie for Roof Cover
22
26
Cable Tie for Front and Back
Cover
70
27 Rod for Pulling Front Door
1
28 Webbing for Winch
12
29
Plastic Plug for lower
tensioning tube No.13
6
Page 5
Page 5
Frame Installation
Step 1: the first arch and roof bracing tube
Page 6
Page 6
Middle Arch
Step 2: middle arches and roof bracing tubes
Page 7
Page 7
Step 3: the last arch and roof bracing tube
Page 8
Page 8
Step 4: purlins, sidewall bracing tubes and base plates
Page 9
Page 9
Step 5: squaring up the frame and fix base plates by anchors
Page 10
Page 10
Cover Installation
Step 1: front cover with door
Page 11
Page 11
Step 2: back cover
Page 12
Page 12
Now your assembly is completed.
Step 3: roof cover
Loading...