east coast Nebraska cot2bed Instruction Manual
Nebraska cot2bed
Assembly and care
instructions
IMPORTANT!
READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
Hardware
A x 8
(dome head)
D x 8 F x 5
B x 8
(flat head)
E x 5
(plastic barrel)
H x 2G x 2 I x 4
C x 3
(short)
Spanner Hexagon Key
1
Wooden Parts
Side x 2
End x 2
Drawer side (L+R)
Drawer support
Base
Drawer back
Drawer front
Drawer base x 2
2
Cot Mode: Assembly 1
B x 2
End
Side
Assembly 2
Base
A x 4
?
D x 4
NOTE: Ensure slot in D is visible when inserted into the base.
The lowest base position is the safest and should always be used in that position as soon as the baby is
old enough to sit up.
IMPORTANT: Ensure the base is the correct way up as shown.
3
Assembly 3
B x 2
Side
Assembly 4
B x 4
A x 4
Base
D x 4
NOTE: Ensure slot in D is visible when inserted into the base.
Ensure that all bolts are tightened fully before use.
4
Drawer: Assembly 1
Drawer Support
Drawer Bases
F x 1
Drawer Front
Assembly 2
Drawer Side (L)
C x 1
Drawer Side (R)
C x 2
Drawer Back
F x 4
5
Assembly 3
E x 2
E x 1
E x 2
I x 4
NOTE: Use the included
spanner to tighten the
castors.
Assembly 4
G x 2
H x 2
6
Day Bed Mode
Bed Mode
Day bed: Remove one side, use with
the base in the lowest position.
Bed: Remove both sides, use with
the base in the lowest position.
7
Care and maintenance
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
In use
WARNING: YOUR CHILDREN’S SAFETY IS YOUR RESPONSIBILITY
The base can be adjusted in height in cot mode, but the lowest position is the safest and should always
be used in that position as soon as the baby is old enough to sit up.
This product is suitable for a mattress of 1200mm long and 600mm wide.
Check the length and width of the mattress, to ensure the gap between the mattress and the sides and
ends does not exceed 30mm.
When used in cot mode, the maximum thickness of the mattress is 100mm.
Check the thickness of the mattress, to ensure that the internal height (surface of the mattress to the
upper edge of the cot frame) is at least 500mm in the lowest position of the cot base and at least
200mm in the highest position of the cot base.
To prevent injury from falls, the cot should no longer be used for the child once they are able to climb
out of the cot.
The bed mode is suitable for a child from 18 months to 4 years old.
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be
placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords.
It should either be placed tightly against any wall or have a gap of 300mm between the wall and the
side of the bed.
This product has been designed and manufactured to: BS EN 716-1: 2017 in cot mode and BS 8509:
2008 +A1: 2011 in bed mode.
Warning: Do not use the cot or bed if any part is broken, torn or missing and use only spare parts
approved by the manufacturer.
Warning: Do not leave anything in the cot or place the cot close to another product, which could
provide a foothold or present a danger of suocation or strangulation, e.g. strings, blind/curtain cords,
etc.
Warning: Do not use more than one mattress in the cot.
Warning: Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires,
gas fires, etc. near the vicinity of the cot.
Warning: Do not place the child’s bed near heat sources, windows or other furniture.
This product can be dismantled carefully for storage and transportation.
East Coast Nursery Ltd, Robertson House
North Walsham, Norfolk, NR28 0BX, UK
For customer care or enquiries:
Call: +44 (0)1692 408802
Email: nursery@east-coast.co.uk
eastcoastnursery.co.uk
EC_NBC2B_130319
Loading...