Installation Instructions
Overhead Door Closer – Model DCT2024
Architectural Hardware Ltd
Eurospec
Stancliffe Street, Mill HIll
Blackburn, BB2 2QR
IMPORTANT INFORMATION
Selecting the correct door closer to suit door size
Power Size Max. Width of Door Max. Mass of Door
2 850mm 40Kg
3* 950mm 60Kg
4 1100mm 80Kg
5 1250mm 100Kg
6 1400mm 120Kg
*Minimum size for use on fire doors
Important notes:
Minimum size 3 MUST be used on fire doors
Hold open arms must NOT be used on fire doors
This product is non handed and can be fitted on both left handed and right handed doors.
Maintenance
Check that the door closer closes the door correctly and adjust as necessary. Ensure fixing screws are tight and periodically
apply light oil or grease to arm knuckle joint
Tel: +44 (0) 1254 274100
Fax: +44 (0) 1254 274111
Web: www.eurospec.co.uk
PLEASE LEAVE THESE INSTRUCTIONS WITH THE END USER
Copyright © 2008 Eurospec
Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Page 1
Door Closer – Model DCT2024 Rev.1
Installation – Fig 1 Application – Angle of opening 180°
Fig 1 – Standard Application (Door closer fitted on pull face of d oor)
Illustrations show anti-clockwise closing door
1. Ensure that the door & surrounding frame are in good
condition & the door closes freely.
2. Select the correct hand of Fig. 1 easi-fit template and with
the door in the closed position, stick template to top corner
of door and frame. (See Figs. 1 & 2)
3. Determine the power size of door closer required. Drill pilot
holes in door & frame according to template. Remove slide
plate and fix door closer body with screws supplied, ensuring
correct fitting holes are used (See Figs. 2 & 3)
4. Carefully detach link arm from adjuster arm & securely fix
adjuster arm shoe to frame ensuring the shoe is rotated in
the correct position to suit power size required. (See Fig. 4)
n
o
i
t
a
c
i
l
p
p
A
d
r
a
d
n
a
t
S
Fig. 1
Fig. 2
5. Place link arm onto closer spindle at right angles
to door, fit securing screw, move link arm and
E
S
U
R
O
F
re-connect to adjuster arm. (See Figs. 4 & 5)
Note: To adjust arm to suit depth of frame, loosen
nut, adjust arm & re-tighten nut.
6. Fit spindle cover cap to underside of closer. (See Fig. 5)
7. Check for correct closing & latching speeds. Adjust if
necessary. (See Fig. 6)
8. Stick easi-exit logo onto indent of slide plate and refit to
door closer. (See Fig.6)
No.1 Closing Speed
T
P
E
H
W
O
F
E
S
R
E
Adjust if
required
S
E
L
O
H
G
N
I
T
T
I
S
4
&
3
S
E
Z
I
T
E
S
U
P
R
O
F
T
T
I
F
E
S
E
H
W
O
2
E
Z
I
S
R
E
S
E
L
O
H
G
N
I
Fig. 3
4
&
2
S
E
Z
I
S
3
E
Z
I
S
No.2 Latching Speed
FAST
Copyright © 2008 Eurospec
SLOW
Fig. 6
No.2
No.1
Fig. 5
Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Page 2
Fig. 4
Door Closer – Model DCT2024 Rev.1
Installation – Fig 61 Application – Angle of opening 180°
Fig 61 – Transom Mounting Application (Door closer fitted on frame on push side of door)
Illustrations show clockwise closing door
1. Ensure that the door & surrounding frame are in good
condition & the door closes freely.
n
o
i
t
ca
i
l
p
p
A
g
n
i
t
n
u
o
M
m
so
n
2. Use Fig.1 easi-fit template and select correc t hand of door.
Stick template to top corner of door and frame, ensuring
closer is mounted on frame and shoe is mounted on door.
(See Figs. 1 & 2)
3. Determine the power size of door closer required. Drill pilot
holes in door & frame according to template. Remove slide
plate and fix door closer body with screws supplied, ensuring
correct fitting holes are used (See Figs. 2 & 3)
4. Carefully detach link arm from adjuster arm & securely
fix adjuster arm shoe to door ensuring the shoe is
rotated in the correct position to suit power size
required. (See Fig. 4)
S
5. Place link arm onto closer spindle at right angles
U
O
F
to door, fit securing screw, move link arm and
re-connect to adjuster arm. (See Figs. 4 & 5)
E
W
O
P
R
S
E
Z
I
S
R
E
G
N
I
T
T
I
F
E
S
E
H
T
a
r
T
Fig. 1
Fig. 2
S
E
L
O
H
4
&
3
E
H
T
E
S
U
W
O
P
R
O
F
N
I
T
T
I
F
E
S
E
Z
I
S
R
E
S
E
L
O
H
G
2
Note: To adjust arm to suit depth of frame, loosen
nut, adjust arm & re-tighten nut.
6. Fit spindle cover cap to upperside of closer. (See Fig. 5)
7. Check for correct closing & latching speeds. Adjust if
necessary. (See Fig. 6)
8. Stick easi-exit logo onto indent of slide plate and refit to
door closer. (See Fig.6)
No.1 Closing Speed
No.2 Latching Speed
FAST
SLOW
No.1
No.2
Adjust if
required
Fig. 3
3
E
Z
I
4
&
2
S
E
Z
I
S
S
Note: Not suitable for power size 4 when fitting in Fig 61 application
Copyright © 2008 Eurospec
Fig. 6
Fig. 5
Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Page 3
Fig. 4
Door Closer – Model DCT2024 Rev.1
Installation – Fig 66 Application – Angle of opening 180° (Power size 3)
Fig 66 – Parallel Arm Application (Door closer fitted on push face of door)
Illustrations show clockwise closing door
1. Ensure that the door & surrounding frame are in
good condition & the door closes freely.
2. Select the correct hand of Fig 66 easi-fit template
and stick body of template to top corner of door.
Fold and stick top of template to underside of
frame. (See Figs. 1 & 2)
3. Drill pilot holes in door & frame according to template.
Remove slide plate and fix door closer body with screws
supplied (see Figs. 2 & 3)
4. Carefully detach link arm from adjuster arm &
securely fix adjuster arm shoe to fig.66 bracket
ensuring the shoe is rotated in the correct position
as shown. (See Fig. 4)
n
o
i
t
a
c
i
l
p
p
A
m
r
A
l
e
l
l
a
r
a
P
Fig. 1
Fig. 2
5. Place link arm onto closer spindle parallel
to door, fit securing screw, move link arm and
re-connect to adjuster arm. (See Figs. 4 & 5)
Note: Adjust arm length as required: Loosen
nut, adjust arm & re-tighten nut.
6. Fit spindle cover cap to underside of closer. (See Fig. 5)
7. Check for correct closing & latching speeds. Adjust if
necessary. (See Fig. 6)
8. Stick easi-exit logo onto indent of slide plate and refit to
door closer. (See Fig.6)
No.2 Latching Speed
Adjust if
required
Fig. 3
G
N
I
S
O
L
C
E
S
I
W
K
C
O
L
C
-
I
T
N
A
G
N
I
S
O
L
C
E
S
I
W
K
C
O
L
C
No.1
Copyright © 2008 Eurospec
No.1 Latching Speed
FAST
No.2
Fig. 6
Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
SLOW
Fig. 5
Page 4
Fig. 4
Door Closer – Model DCT2024 Rev.1
Loading...