Thank you for purchasing our product.
Please read this User’s Manual before
using the product. Change without Notice
ET-DVR-0450
User’s Manual
Safety Precautions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
CA
UTION
RISK O F ELECTR ICAL
SHOCK. DO NO T OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVE R (OR BACK) , NO USER
SERVICEABLE PAR TS REFE R SERVICING TO
QU ALIFIED S ERVICE PERSONNE L.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of insulated
dangerous Voltage within the product’s enclosure that may be
sufficient magnitude to constitute risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
Warranty
and Service
EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR
Attention: installation should be performed by qualified service
Personnel only in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have
power supplied to the unit whenever the power cord is inserted into
the power source; however, the unit is operational only when the
ON-OFF switch is the ON position. The power cord is the main power
disconnect for all unites.
There are no serviceable parts for this unit, call for your agent for
details.
2
2
About this document
Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this
User’s Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
Before reading this document
1. This document is intended for both the administrator and users of stand alone DVR Model.
2. This manual contains information for configuring, managing and using stand alone DVR
Model.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture.
4. Be sure to read this manual before using stand alone DVR Model.
5. For questions and technical assistance of this product, contact your local dealer.
►Strong recommendation on installation of the DVR unit
1. Check electricity at the place you want to install the DVR unit is stable and meets our
electricity requirements. Unstable electricity will cause malfunction of the unit or give critical
damage to the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged. Do not put any objects just beside exhaust port(fan)
on the left side of the unit and do not close up an opening (fresh air in-take) on the right side
of the unit..
3
3
FRONT PANEL
1.PLAY Video playback function .
2.REC Record button (Start / Stop )
3.SHIFT + MODE Change the record quality level . (HST / HIG / NOR / LOW / LST).
4.SHIFT Video backup function.
5.MODE
Change display mode (quad mode ) / Full channel select
6.MENU Display menu setup
7.ENTER Change the setting value .
8. UP / STOP
9. DOWN / PAUSE
10. REW Direction left button/ Reverse playback / play speed /
11. FF Direction right button/ Forward playback / play speed /
Direction button UP / Playback stop button ▲ /▓
Direction button down / Playback pause ▼ / ▌▌
4
4
REAR PANEL
1. DC IN Power code in 12V/ 2A
2. USB USB device slot
3. CAM IN Camera 1 ~ 4 input BNC type
4. MONITOR Monitor out
5
5
REMOTE Controller
The key on the remote controller function control is same as the front keypad of the unit.
Record button (Start / Stop )
REC
MENU
BACKUP
SEARCH
HST
HIG
NOR
LOW
LST
ENTER
～
Display menu setup
Video backup function.
Video search function
Video record quality level (Highest)
Video
record quality level (High)
Video record quality level (Normal)
Video record quality level (Low)
Video record quality level (Lowest)
Change the setting value .
Direction button UP /
Playback stop button
Direction button down /
Playback pause
Direction right button /
Forward playback / play speed
Direction left button /
Reverse playback / play speed
Channel 1 ~ channel 4
Full screen display
Quad display screen
6
6
1
.
OPERATION
Power on the DVR system , the real-time video can be seen by 4 quad screen or full screen display .
User can press “MODE” button to switch the display mode .
Playback mode : Press “PLAY” button , user can search date-time to playback .
Record mode : Press “REC” button start to record . User can press “SHIFT” + “MODE” button to
change the record quality .Record quality level have 5 types : HST / HIG / NOR / LOW / LST .
Press “SHIFT” button , it will show an icon
change record frame rate and quality level and it will show a message
User change the different record level , it means that user change the record quality , below table
show the mapping .
HST
Level
60
HIG
60
at top line on screen then press “MODE” button to
on top-right screen .
NOR
16
LOW
8
LST
8
FPS
(15/each)
(15/each)
(4/each)
(2/each)
(2/each)
Quality High Normal Normal Normal Low
Backup mode :
Before backup, USB device is required. User need insert USB device into USB slot before backup.
Backup file size can not exceed 3GB
1. On playback mode, press “SHIFT” button to start backup.
2. When user press “SHIFT “ button , it means the start time of backup .
3. When user press “SHIFT” button second time , it means the end time of backup .
4. The system will auto reading USB device then start to backup data .
7
7
Icon Indicator:
In live mode or playback mode , the icons show at top line on screen to notify user the system status ,
below are the icons status .
Live mode Forward
Recording Pause
Video loss Reverse
Motion detect SHIFT mode
Display Channel Hard disk usage
Notice :
In real-time mode , user can press direction key –Up ▲ 5 times to enable key lock .
And press direction key –Up ▲ 5 times again to disable key lock
8
8
2
.
SYSTEM SETUP
When user first time use admin menu setup , please press direction key
▲ ▲ ▼ ▼ and “MENU” ,then user can into admin menu setup successful.
2.1 Camera Setup
User can setup each channel display status and adjust the cameras Brightness , contrast, and
saturation . Right adjustment of each element will increase picture quarterly displayed. We
recommend you to adjust each element of cameras and monitor to be connected to the DVR .
Display title on screen
Title :
2.2 Record Setup Use this function to setup the record frame rate of each channel
Totally frame rate is
60 fps(NTSC) / 50 fps (PAL)
9
9
2.2.1 Schedule Record Frame rate
User can use the direction left button to decrease the frame rate or direction right button
to increase the frame rate value .
After changed the frame rate value , press “MENU” button to exit the setup menu .
Schedule record will follow these frame rate values .
2.2.2 Motion Record Frame rate
User can use the direction left button to decrease the frame rate or direction right button
to increase the frame rate value .
After changed the frame rate value , press “MENU” button to exit the setup menu .
Motion record will follow these frame rate values .
2.2.3 Record Quality:
Low / Normal / High (See record time table page 11)
2.2.4 Event Rec Duration:
5/ 10/ 15/ 20/ 25/ 30 seconds. Duration time recording after event
2.2.5 Auto Record:
Off / 1 ~ 8 minutes selectable
When auto record is set to 1 ~ 8 minutes , the DVR will start recording after 1~ 8 minutes no
operation .
10
10
2.2.6 Schedule Record
Use the left button or right button to select time and use the “Enter” button to change
record type .
Notice:
1. Each channel has own frame rate adjustment in different recording mode.
2. In 24 hours, user can adjust each channel frame rate in different record mode. Such as schedule
or motion detection .
3. Press “ENTER” button to change different record mode
Record Time Table: 80GB HD
Record Quality: Low. Average: 5 KB;
REC FPS(total) 60 30 15 10
REC Hour 72 hr 148 hr 296 hr 444 hr
Record Quality: Normal. Average 10 KB;
REC FPS(total) 60 30 15 10
REC Hour 36 hr 74 hr 148 hr 222 hr
Record Quality: High. Average 20 KB;
REC FPS(total) 60 30 15 10
REC Hour 18 hr 37 hr 74 hr 111 hr
**Actual recording time is base on live environment. This table is only for reference.**
20 K x 30 (frame rate) x 60 (mins) x 60 (secs) = 2160000 K = 2160 M / hr
2160 M / hr x 24 = 51840000 K = 51840 M = 51.84 G / (1 Day)
11
11
2.3 Motion Detection
User can setup each channel with different motion detection.
2.3.1 Channel :
User can setup different motion detection of channels (1~ 4 )
2.3.2 Sensitivity :
Off / 1 / 2 / 3 / 4 , Off means disable motion detection , 1 means high sensitivity ,
4 means very low sensitivity
2.3.3 Alarm Duration :
This function is disable now.
2.3.4 Motion Pop up :
OFF/ 1 ~ 30 Seconds /CONT
Each channel jumps to full screen when motion triggered. Quad screen display if more than
two cameras motion triggered.
2.3.5 Motion Area :
Use direction button Left or Right to move position then press “ENTER” button , start to select
the motion area and finally press “ENTER” button to stop .
Detected area
12
12
2.4 SCREEN
Let user setup the screen display.
2.4.1 Border: Split border on or off .
2.4.2 Video Adjustment: Video screen position movement. Use direction button to move.
2.4.3 Video system : NTSC/ PAL/ AUTO
2.4.4 Output: 720x448 : NO / Off
ON OFF
2.5 System Setup
2.5.1 Hard Disk Setup :
Overwrite Enable : Yes -> When Hard Disk full , DVR continue to record
Format HDD : Initial the HDD , Please format hard disk before starting record
Hard Disk does not support WD AV serial type.
No -> When Hard Disk full , DVR stop record .
13
13
2.5.2 Time Setup
User can setup daylight saving time in this menu , also can use up-down
button move to time set change the date and time.
2.5.3 Buzzer Setup
System Buzzer: OS operating
Key Press Buzzer: Button operating
Motion Buzzer: Motion detection warning
Video Loss Buzzer Video loss warning
14
14
2.5.5 F/W Upgrade
Stop all hard disk working before update, select F/W upgrade and then press ENTER to search
firmware.
1. Searching Firmware
2. Press ENTER upload, press STOP cancel
3. Firmware Reading
4. Firmware uploading
DVR auto reboot after F/W upgrade finished .
15
15
2.6 Search
User can search video image by Time search and Event list.
2.6.1 Time Search:
1. Press “ENTER” into time search menu .
2. Use direction left or right button to move the cursor position .
3. Press “ENTER” to change date and time .
16
16
4. Press “MENU” return to the previous screen and move cursor to Search.
5. Press “ENTER” to start the searching.
6. Wait until the unit starts to playback.
Playback mode
Forward speed: x 2 / x 3 / x 4
(Direction right button)
Reverse speed: x 8 / x 16 / x 32
(Direction left button)
Press “STOP” button return to live mode.
2.6.2 Event List mode
Each event will list on event list , user can use direction button up and down to move and it will show
the event start time and end time for user reference . After select an event press “ENTER” start to
playback. Event list total can save 120 records
17
17
2.7 Language
Standard is English / Chinese
2.8 Exit
User needs to save changes if any function value has changed then exit menu.
18
18
3
.
Player Software
3.1 Start to play :
1 2 3 4 5 6 7 8 9 10 11
1 Open Backup file 7 Play
2 Fast Reverse 8 Fast Forward
3 Play Reverse 9 Capture image
4 Previous Frame 10 Full Screen (channel switch)
5 Pause 11 Quad Screen
Next Frame
6
3.2 AVI file format Export : Click the the mouse right button , choose the Export -> AVI function ,
This function can exdport .vvf files to .avi format .
Percentage of the export AVI progress
Browse for the source file
Browse a path for file output
Select a compression codec
19
19
3.3 Capture file From Hard Disk or backup file :
When use the player to play Hard Disk or backup file , it offers the Capture function and let user to
capture video session from Hard Disk or backup file .
Operation steps :
1. Open the backup file .
2. Press Pause key to pause the screen and then click mouse right button, it will display menu then
choose the “Capture“ function . ( see below picture )
3. Choose the “Mark In” to set the capture start point .
4. Press play key to start play until user desire video screen .
5. Press pause key and choose the “Mark out” to set the capture end point .
6. Choose the “Export” , then user can export this session of video from backup file .
Notice :
When start to export the video , the computer will be in busy state , user have to wait until the
operation stop 。
20
20
4
.
Specification
Model 4 CH Digital DVR
Input 4 CH Inputs 1.0Vp-p, 75ohm unbalanced (BNC Type)
Output Main monitor x 1
S/N Ratio More than 40dB
0Color 6.7 Million
Monitoring Method
Channel Display Single / Quad channel
Screen Quality
640(H) x 448(V) Active Pixels(NTSC);
640(H) x 544(V) Active Pixels (PAL)
Display Rate 120 fps (NTSC) / 100 fps (PAL)
Recording/ Play Function
Recording (Max) NTSC Max 60 fps(NTSC); Max 50 fps(PAL)
Record Quality High, Normal, Low
Compressed Picture Storage: M-JPEG
Recording Control Normal / Schedule / Event
Motion detect Record 5 ~ 30 seconds
Playback Mode Time list / event list / Date & Time search
Backup and Copy
Backup Event Backup / Video Data backup via USB device
Backup file play Client software to play files
Other Function
Operation Mode Record / Play
Monitoring Firmware Watchdog
Recovery Auto-Reboot by Watchdog
Operation Mode Duplex (Record +Playback )
Control Device Front key/ Remote controller
Daylight Saving Supported
Language English / Chinese
Motion Detect 16 x16 grids camera for all channel
3.5 inch HDD x 1 SATA
Storage (It does not support WD AV serial type , for example WD5000AVVS)
Firmware Upgrade Support USB firmware upgrade
HDD Record Mode Full stop / overwrite
Power Supply DC12V / 2A
Operating Temperature 0 ºC ~ + 55 ºC
21
21
Loading...