EarthWise LHT14022 Operator's Manual
OPERATOR’S MANUAL
CORDLESS 22‖ 40V LITHIUM HEDGE TRIMMER
This product is covered by U.S. patents and other international patents
Copyright. All Rights Reserved.
LHT14022
CA Compliant Charger Included (Model No. CHL80040)
Your hedge trimmer has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
BATTERY MUST BE CHARGED BEFORE FIRST USE
Thank you for your purchase.
DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS, SERVICE QUESTIONS?
CALL 1-800-313-5111 BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY WARNINGS
TO REDUCE RISK OF INJURY:
Before any use, be sure everyone using this tool reads and
understands all safety instructions and other information
contained in this manual.
CAUTION: Wear appropriate personal hearing protection
during use. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
GENERAL SAFETY
KEEP CHILDREN AWAY - All visitors, children and pets
should stay at a safe distance from the work area.
DRESS PROPERLY – Don’t wear loose clothing or jewelry.
Wear protective hair covering to contain long hair. They
can be caught in moving parts. Use of rubber gloves and
substantial footwear is recommended when working
outdoors.
USE SAFETY GLASSES –Wear safety glasses with side
shields or goggles that are marked to comply with ANSI Z87.1
standard when operating this product. Use face or dust mask
if environment is dusty.
USE RIGHT APPLIANCE – Do not use an appliance for any
job except that for which it is intended.
REMOVE BATTERY FROM HEDGE TRIMMER when not in
use or when servicing or cleaning. Do not leave unattended.
CHECK DAMAGED PARTS – Before further use of the
hedge trimmer, a guard or other part that is damaged should
be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting and any other condition that may affect its
operation. A guard or other part that is damaged should be
properly repaired or replaced. Call our customer service
help line at 1-800-313-5111 for assistance.
LIGHTING - Only operate trimmer in daylight or good
artificial light.
DON’T OVERREACH – Keep proper footing and balance at
all times.
WARNING: Do Not use the hedge trimmer with any type of
accessory or attachment. Such usage might be hazardous.
AVOID DANGEROUS ENVIRONMENTS – Don’t use
trimmer in rain, damp or wet locations. Do not operate
trimmer in gaseous or explosive atmospheres. Motors in
these tools normally spark, and the sparks might ignite
fumes.
AVOID UNINTENTIONAL STARTING – Don’t carry trimmer
with finger on switch.
DANGER: Risk of cut. Keep hands away from the blades.
Keep both hands on handles when power is on.
DANGER: DO NOT ATTEMPT to remove cut material or
hold material to be cut when blades are moving. Make sure
trimmer switch is off when clearing jammed material from
blades. Do not grasp the exposed cutting blades or cutting
edges when picking up or holding the hedge trimmer.
Save these instructions and review frequently prior to use
and in instructing others.
WARNING: When using electric gardening appliances, basic
safety precautions should always be followed to reduce risk
of fire, electric shock, and personal injury, including the
following:
READ ALL INSTRUCTIONS
CAUTION: Blades coast after turned off.
DON’T FORCE HEDGE TRIMMER – It will do the job
better and with less likelihood of a risk of injury at the rate
for which it was designed.
STAY ALERT – Watch what you are doing. Use common
sense. Do not operate hedge trimmer when you are tired
or under the influence of drugs, alcohol or medications.
STORE IDLE HEDGE TRIMMER INDOORS – When not
in use, the hedge trimmer should be stored indoors in a
dry and high or locked-up place, out of reach of children.
MAINTAIN TRIMMER WITH CARE – Keep cutting blades
sharp and clean for best performance and to reduce the
risk of injury. Inspect extension cord periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
WARNING: California Proposition 65: This product
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
WARNING: Some dust and debris created by this tool
could contain chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
-chemicals in fertilizers
-compounds in insecticides, herbicides and pesticides
-arsenic and chromium from chemically treated lumber
Your risk of exposure to these chemicals varies
depending on how often you do this type of work. To
reduce your exposure, work in a well ventilated area and
with approved safety equipment such as dust masks that
are specially designed to filter out microscopic particles.
WARNING: DO NOT USE ON A LADDER OR
UNSTABLE SUPPORT. Stable footing on a solid surface
enables better control of the power tool in unexpected
situations.
2
FEATURES
PRODUCT SPECIFICATIONS
LHT14022
Input….………………………….………………………….........40 V, DC Only
No Load Speed ………………………..………………...........2800 Stroke per Min.
Blade Length……………………………...……………………..22 in.
Maximum Cut ………………….…………………………….... 5/8 in.
Weight ……………………………………………………..........2.0 Ah 8.4 lb/ 4.0Ah 9.3 lb
Aluminum Blade Support - Rubber Over Molded Handle - Hardened Steel Blades
FRONT
HANDLE
SECONDARY
SWITCH
BLADE COVER
BATTERY
PACK
REAR HANDLE
TRIGGER SWITCH
BLADE SUPPORT
BLADE
SAFETY
GUARD
CHARGER
3
ASSEMBLY
PACKING LIST
— Hedge Trimmer
— Charger
— Battery Pack
— Blade Cover
—Instruction Manual
WARNING: If any parts are damaged or missing do not
operate this product until the parts are replaced. Failure to
heed this warning could result in serious personal injury.
Installing / Removing Battery Pack
WARNING: Always remove battery pack from your
tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that could
cause serious personal injury.
To install battery pack: （Fig. 1)
■ Align grooves on battery pack with raised ribs in the
tool’s battery port and slide the battery pack into the tool.
Press firmly on the battery to ensure a good connection.
WARNING: Make sure the latch on the battery snaps
in place and the battery pack is fully seated and
secure in the battery port before beginning operation.
Failure to securely seat the battery pack could cause
the battery pack to fall out, resulting in serious
personal injury.
To remove battery pack: ( Fig. 2)
■ Pull upward on the battery pack latch button and pull the
battery pack out.
WARNING: To avoid serious personal injury, always
remove the battery pack and keep hands clear of the
trigger when carrying or transporting the tool.
Latch
Fig. 1
Battery Pack
Battery Port
Fig. 2
UNPACKING
This product requires no assembly.
Carefully remove the product and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Inspect the product carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-313-5111 for assistance.
OPERATING
Starting / Stopping the Hedge Trimmer
To start:
■ Remove the blade cover.
■ Hold the unit by both handles.
■ Grasp the front handle firmly,pushing the secondary
switch toward the handle.
■ Press the switch trigger to begin normal operation.
Front Handle
To stop:
■ Release the switch trigger or the secondary switch to stop
the hedge trimmer.
CAUTION: Blade coasts after turned off.
Do not use under wet conditions.
Do not store with switch locked on.
WARNING: To guard against injury, observe the following:
WARNING: Do not allow familiarity with this type of product
to make you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
Secondary Switch
Switch
Trigger
Read instruction manual before using,
Save instruction manual.
Keep hands away from blades.
Keep hands on handles. Don’t overreach.
Latch
Battery Port
4
TRIMMING INSTRUCTIONS
1. WORKING POSITION– Maintain proper footing
and balance and do not overreach. Wear safety
goggles, non--skid footwear and rubber gloves
when trimming. Hold the tool firmly in both hands
and turn the tool ON. Always hold the trimmer, as
shown, with right hand on the switch handle and left
hand on the front. Never hold the tool by the blade
guard. Keep unit below waist level.
2. LEVEL HEDGES—To obtain exceptionally level
hedges, a piece of string can be stretched along the
length of the hedge as a guide.
CAUTION: Do not use the trimmer for cutting stems
greater than 3/4‖. Use the trimmer only for cutting
normal shrubbery found around houses and
buildings.
WARNING: Always keep both hands on the hedge
trimmer handles. Never hold shrubs with one hand
and operate the hedge trimmer with the other.
Improper operation of the hedge trimmer could result
in serious injury.
DANGER: Never cut near electric cords or lines. If
blade jams on any electrical cord or line, DO NOT
TOUCH THE BLADE! IT CAN BECOME
ELECTRICALLY LIVE AND VERY DANGEROUS.
Continue to hold the hedge trimmer by the insulated
rear handle or lay it down and away from you in a
safe manner. Disconnect the electrical service to the
damaged line or cord before attempting to free the
blade from the line or cord. Contact with the blade,
other conductive parts of the hedge trimmer, or live
electric cords or lines will result in death by
electrocution or serious injury.
WARNING: Clear the area to be cut before each
use. Remove all objects such as cords, lights, wire,
or loose string which can become entangled in the
cutting blade and create a risk of serious personal
injury.
3. TRIMMING NEW GROWTH—A wide, sweeping
motion, feeding the blade teeth through the twigs is
most effective. A slight downward tilt of the blade in
the direction of the motion gives the best cutting.
4. SIDE-TRIMMING HEDGES—Rotate handle to
desired angle.Begin at the bottom and sweep up.
5
CHARGING THE BATTERY PACK
Charge the battery pack only with the charger provided.
Allow at least 75 minutes of charge time for 2Ah battery or 120
minutes of charge time for 4Ah battery before initial use of the
hedge trimmer.
Make sure the power supply is normal household voltage, 120
volts, 60Hz, AC only.
The battery charger should be operated in temperatures
between 32 and 100 degrees F.
The battery should be charged in a cool, dry place.
2 to 3 initial charging/discharging cycles may be required to
achieve maximum run time/capacity.
DO NOT attempt to open the charger or the unit. There are no
customer serviceable parts inside. Call customer service
helpline at 1-800-313-5111 for assistance.
DO NOT incinerate battery packs even if they are severely
damaged or completely worn out. They can explode in a fire
causing injury.
DO NOT charge appliance in rain, or in wet locations.
Use the battery charger indoors only.
Disconnect charger from the power supply when not in use to
prevent damage to the charger during a power surge.
When fully charged, the battery can be safely stored in
temperatures down to -4 degrees F for a period of up to four
weeks, before requiring charging. Fully charge battery pack
every 90 days.
If over a period of time the battery pack quickly runs down
after a full 75 or 120 minutes charging period, a replacement
battery pack is needed.
To prevent permanent damage to the battery, never store in a
discharged condition.
WINTER STORAGE - Fully recharge before storage and then
again every 90 days.
Since the battery will not develop a memory, it does not have
to be fully discharged before recharging.
A small leakage of liquid from the battery cells may occur
under extreme usage, charging or temperature conditions.
This does not indicate a failure. However, if the outer seal is
broken and this leakage gets on your skin.
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice of
vinegar.
c. If the battery liquid gets in your eyes, flush them with
clean water for a minimum of 10 minutes and seek
immediate medical attention.
TO CHARGE - SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS
Constant Green (A) = Power is ON
Constant Green (A) + Constant Red (B)= Battery is charging
Constant Green (A) + Constant Green (B)= Battery is fully charged
Constant Green (A) + Alternately flashing Red and Green(B) = Temperature
Abnormality
Constant Green (A) + Red indicator light (B) flashing = Something is
wrong with battery
A
Battery
Pack
Charger
BATTERY DISPOSAL
Remove the battery pack from the Cordless Hedge Trimmer, cover the terminals with heavy duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove any components. This product contains lithium-ion batteries which must be
recycled or disposed of properly. Local, state or federal laws may prohibit disposal of these batteries in the municipal solid waste or
rural trash pick up systems.
The RBRC seal on the Li-Ion battery pack indicates that the cost to recycle the battery pack at the end of its useful life has already
been paid by The Great States Corporation/American Lawn Mower Company. It is illegal to place spent Li-Ion batteries in the local
municipal solid waste or in the trash. RBRC in cooperation with The Great States Corporation/American Lawn Mower Company has
provided an environmentally friendly and easy way to recycle spent Li-Ion batteries. Just contact your local recycling center or call
1.800.8.BATTERY for information on where to drop off the spent battery.
6
MAINTENANCE
If you drop the trimmer, carefully inspect it for damage. If the blade is
bent or cracked, handles broken or if you see any other condition that
may affect the trimmer’s operation, it must be repaired before putting it
back into use. Call our customer service help line at 1-800-313-5111 for
assistance.
LUBRICATE BLADES - Stop the unit and rem ove
the battery pack. Then remove any debris on
blades. Apply a light machine oil along the edge of
the top and bottom blade supports. Make sure
handles remain clean and dry.
CAUTION: Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact with plastic parts.
They contain chemicals that can damage, weaken or destroy plastic.
Make sure the battery is detached from the unit, then use only mild soap
and a damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by a qualified
individual using only identical replacement parts.
The cutting blades are made from high quality, hardened steel and with
normal usage, they will not require re-sharpening. However, if you
accidentally hit a wire fence, stones, glass or other hard objects, you
may put a nick in the blade. There is no need to remove this nick as long
as it doesn’t interfere with the movement of the blade. If it does interfere,
make sure the battery is detached from the unit and use a fine toothed
file or sharpening stone to remove the nick.
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals Do not store the tool on or adjacent to
fertilizers or chemicals.
Cleaning the Hedge Trimmer
■ Stop the motor and remove the battery pack.
■ Slide the blade cover over the blade.
■ Clean dirt and debris from the body of the hedge trimmer, using a damp
cloth with a mild detergent.
NOTE:Do not use any strong detergents on the plastic housing or the
handle. They can be damaged by certain aromatic oils such as pine and
lemon, and by solvents such as kerosene.
■ Moisture can cause a shock hazard. Wipe off any moisture with a soft dry
cloth.
■ Use a small brush or the air discharge of a small vacuum cleaner brush to
clear dust or debris from the air vents on the motor housing.
Storing the Hedge Trimmer
■ Remove the battery pack and store it out of the reach of children when
storing the hedge trimmer.
■ Clean the hedge trimmer thoroughly before storing. Store the hedge
trimmer in a dry, well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals and de-icing salts.
■ Always place the blade cover on the cutting blades before storing.
TROUBLESHOOTING
Problem Possible Cause Possible Solution
Unit does not run Battery not making contact Check battery is fully inserted
Trigger switch not operational Check that lock off button is fully depressed before moving trigger
Battery not installed properly Check battery installation
Battery not charged Check battery charging requirements
Slow running, noisy or hot blades Dry, corroded blades Lubricate blades
Blades or blade support bent Straighten blade or blade support
Bent or damaged teeth Straighten teeth
Loose blade bolts Tighten blade bolts
Battery will not charge Battery not inserted into charger Insert battery into charger until red LED appears
Charger not plugged in Plug charger into a working outlet
Check current at receptacle by plugging in a lamp or other appliance
Check to see if receptacle is connected to a light switch which turns
power off when you turn out the lights.
Surrounding air temperature too hot
or too cold
Move charger and tool to a surrounding air temperature between 32°
F (0° C) and 100° F (37,8°C)
CALL US FIRST !!
Call us first with questions about operating or maintaining your hedge trimmer
at 1.800.313.5111 between 8:00 a.m. – 5:00 p.m. Eastern Standard Time,
or send emails to earthwise@reelin.com.
7
OPERATOR’S MANUAL
CORDLESS 22‖ 40V LITHIUM HEDGE TRIMMER
WARRANTY
LIMITED WARRANTY FOR CORDLESS ELECTRIC MODELS
This product is manufactured for The Great States Corporation/American Lawn Mower Company, Shelbyville, IN, which
warrants to the original owner of this product that each new product and service part is free from defects in material and
workmanship and agrees to repair or replace under this warranty any defective product or part for two (2) years from the
original date of purchase except for the conditions and circumstances listed below. Proof of purchase (original dated sales
receipt) must accompany all warranty claims.
THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:
Products sold damaged or incomplete, sold ―as is‖, sold
reconditioned, or used as rental equipment.
Delivery, installation, or normal adjustments explained in
the operator’s manual.
Damage or liability caused by shipping, improper
handling, improper installation, incorrect voltage or
improper wiring, improper maintenance, improper
modification, or the use of accessories and/or
attachments not specifically recommended.
Repairs necessary because of operator abuse or
negligence, or the failure to install, operate, maintain, or
store the product according to the instructions in the
operator’s manual.
This warranty is not transferable and only applies to
product sold directly from an authorized retailer. This
warranty does not apply to any product, new or used,
purchased through unauthorized third-party channels.
Damage caused by cold, heat, rain, excessive
humidity, corrosive environments and materials,
or other contaminants.
Expendable items that become worn during normal use.
Cosmetic defects that do not interfere with tool
functionality.
The expense of delivering the product to the vendor and the
expense of returning the product and/or replacement parts
back to the owner.
Freight costs from customer to vendor.
Repair and transportation costs of products or
parts determined not to be defective.
ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL
LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT
FROM ANY DEFECT, FAILURE, OR MALFUNCTION
OF THE PRODUCT. Some states do not allow the
exclusion or limitation on how long an implied warranty
lasts, so the above limitations may not apply to you.
ANY NON-RESIDENTIAL USE OR COMMERCIAL USE
VOIDS ALL WARRANTIES.
The Great States Corporation
American Lawn Mower Company
830 Webster Street
Shelbyville, IN 46176
Phone 1-800-313-5111
www.earthwisetools.com
In a continued c ommitment to improve quality, the Manufacturer reserves the right to
make component changes or design changes when necessary.
Rev. 12/12/2016
Loading...