For Easy On-line registration, Go To "www.earthquakesound.com/form_reg.htm"
Table of Contents
Page# 3……......Warranty guidelines
Page# 4……......Components set dimensions
Page# 5……......Components set features and specifications
Page# 6 & 7……Coaxial speaker dimensions
Page# 8…….......Coaxial speaker features and specifications
Page# 9…….......Speaker installation
Page# 10…….....Separate installation/ Component set wiring diagram
Page# 11…….....Warranty card
Thank you for choosing Earthquake Sound’s line of VTEK coaxial and component speakers for superior enhancement of your vehicle’s
audio system. With proper installation and responsible listening, your VTEK speakers will give you years of near perfect sound reproduction.
We strongly recommend you to have your new VTEK speakers installed by an authorized Earthquake Sound dealer: Installation
professionals employed by your dealer have the correct tools and knowledge to install your speakers neatly and successfully. Also, when
your new products are installed by an authorized dealer, your product will include a FIVE YEAR LIMITED WARRANTY. If you choose to
perform your own installation, your warranty will be subject to limitations. Over the counter authorized dealer warranties may very from one
dealer to the next. Please read the warranty information in its entirety and use good judgment when making these vital decisions.
Five (5) year limited warranty:
Earthquake warrants the original purchaser that all Factory Sealed New Audio Products be free from defects in material and
workmanship under normal and proper use for a period of five (5) years from the date of purchase (as shown on the original bill of sale with
serial number affixed/written on it). The five (5) year warranty period is valid only if an authorized Earthquake dealer properly installs the
product and the warranty registration card is properly filled out and sent to Earthquake Sound Corporation. If a non-authorized party installs
the product a ninety (90) day warranty period will be applied.
(A) Five (5) years limited warranty plan coverage guidelines:
• First year: Earthquake pays for labor, parts, and ground freight (only in US mainland, not including Alaska and Hawaii).
• Second year: Earthquake pays for labor and parts only, customer must pay freight both ways.
• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for parts and freight both ways.
(B) Warning:
Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem(s) will not be covered by the
five (5) year limited warranty. Customer will be charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to
customer.
(C) Earthquake will repair or replace - at our option - all defective products/parts subject to the following provisions:
• Defective products/parts have not been altered or repaired by other than an Earthquake factory approved technician.
• Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged by improper line voltage, used with
incompatible products, or have its serial number or any part of it altered, defaced or removed, or have been used in any way that is
contrary to Earthquake's written instructions.
(D) Warranty Limitations:
Warranty does not cover products that have been modified or abused. Including but not limited to the following:
• Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper use of cleaning materials/methods.
• Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust cap, burnt speaker voice coil.
• Fading, deterioration of speaker components & finish due to improper exposure to elements.
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of cleaning material.
• Burnt tracers on PCB.
• Product/part damaged due to poor packaging or abusive shipping conditions.
• Subsequent damage to other products.
High-Performance and Sound Quality
EARTHQUAKE SOUND
warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with
a copy of the sales invoice.
A
(E) Service Request:
To receive product/s service, contact Earthquake service department at (510) 732-1000 and request an RMA number (Return
Material Authorization), items shipped without a valid RMA number will be refused. Make sure you provide us with your complete/correct
shipping address, a valid phone number, and a brief description of the problem you are experiencing with the product. In most cases, our
technicians might be able to resolve the problem over the phone, thus eliminating the need to ship the product.
(F) Shipping Instructions:
Product/s must be packaged in its original protective box(s) to minimize transport damage. Shipper claims regarding items
damaged in transit must be presented to carrier. Earthquake Sound Corporation reserves the right to refuse product improperly packed.
Original bill of sale must accompany product returned for service. We encourage you to include with the package a written description of the
problem. Ship product to: Earthquake Sound Corp. 2727 Mc Cone Avenue, Hayward, CA 94545. Ph (510) 732-1000. You are responsible for
the cost of shipping the product to Earthquake Sound Corporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from the five (5) years limited warranty policy
must be resolved according to the laws & regulations of the county of Alameda -California.
Please keep this warranty information in your files for
future reference if necessary. It is recommended that
you stick your serial number here for future reference.
SERIAL NUMBER
Alternatively you may register your products online at
http://earthquakesound.com/form_reg.htm
2
WWW.EARTHQUAKESOUND.COM
EARTHQUAKE SOUND • 5-YEAR WARRANTY3
Page 3
VTEK Component Crossover Dimensions (For 5” and 6” sets)
VTEK MATCHED COMPONENT SPECIFICATIONS
A
C
INPUT
B
A
Height
1.405", 35.7mm
Model
Woofer• 5” driver / electroplated carbon fiber cone body
B
Width
C
Depth
WOOFER
TWEETER
3kHZ
PASS
+
- -
+
-3dB
-
5.07”, 129mm
4.21”, 107mm
Tweeter
Frequency Response:
1,500Hz - 22kHz
Crossover Networks
VTEK-25C Dimensions
VTEK-MC5
• 25mm (over 1”) ASV voice coil
• Nomax/Romax high-performance spider
• Over hung butyl rubber surround
• 1” silk dome
• Soft rubber suspension
• Neodymium magnet
• Multiple mounting positions
• 2-way network
• Military grade polypropylene film capacitors
• +3db/-3dB tweeter & woofer adjustment
• Poly switch tweeter protection
VTEK-MC6
” driver / electroplated carbon fiber cone body
• 6.5
• 30mm (almost 1.25”) ASV voice coil
• Nomax/Romax high-performance spider
• Over hung butyl rubber surround
• 1” silk dome
• Soft rubber suspension
• Neodymium magnet
• Multiple mounting positions
• 2-way network
• Military grade polypropylene film capacitors
• +3db/-3dB tweeter & woofer adjustment
• Poly switch tweeter protection
This diagram displays only the raw tweeter.
Mounting components vary in size.
Diameter
B
Height
A
B
1.405", 35.7mm
.75”, 19.05mm
Power Recommendations
Frequency Response
Sensitivity
Nominal Impedance
50 - 500 Watts
45Hz - 23kHz (±3dB)
91dB @ 1W/1M
4 ohm
50 - 600 Watts
40Hz - 23kHz (±3dB)
91dB @ 1W/1M
4 ohm
VTEK-5C Dimensions
A
Frame outer
diameter
B
C
Grille tray outer
diameter
C
D
E
F
B
Grille protrusion
D
Mounting depth
E
Magnet width
F
Cut out hole
VTEK-6C Dimensions
A
Frame outer
diameter
B
C
D
Grille tray outer
diameter
C
Grille protrusion
D
Mounting depth
5.13”, 130.34mm
6.49”, 165mm
71”, 18.034mm
1.92”, 49mm
4.21”, 107mm
4.21”, 107mm
6.49”, 165mm
7.07”, 179.5mm
0.94”, 24mm
2.51”, 64mm
VTEK-MC5 Included Components and Parts
• Two VTEK-5w, 5.0-inch (127mm) carbon fiber woofers
• Two VTEK-25t, 1-inch (25mm) silk dome tweeters
• Two VTEK-500c crossover networks
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Two compact surface-mount fixtures
• Two metal woofer grilles with trays
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Twelve 8 x 1.25” (30mm) sheet metal screws
• Four 6 x .625” (16mm) sheet metal screws
• Two 1-inch (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Eight mounting clips for woofer mounting
• Two 6.4mm female crimpable connectors
• Two 4.7mm male crimpable connectors
• Two 2.8mm male crimpable connectors
• Twelve crimpable spade connectors
VTEK-MC6 Included Components and Parts
• Two VTEK-6w, 6.50-inch (160mm) carbon fiber woofers
• Two VTEK-25t, 1-inch (25mm) silk dome tweeters
• Two VTEK-650c crossover networks
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Two compact surface-mount fixtures
• Two metal woofer grilles with trays
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Twelve 8 x 1.25” (30mm) sheet metal screws
• Four 6 x .625” (16mm) sheet metal screws
• Two 1-inch (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Eight mounting clips for woofer mounting
• Two 6.4mm female crimpable connectors
• Two 4.7mm male crimpable connectors
• Two 2.8mm male crimpable connectors
• Twelve crimpable spade connectors
B
All specifications are subject to change without notice.
4
E
E
Magnet width
F
F
Cut out hole
4.03”, 102.29mm
5.66”, 144mm
WWW.EARTHQUAKESOUND.COM
EARTHQUAKE SOUND • VTEK COMPONENT SPECIFICATIONS5
Page 4
VTEK-42 Dimensions
VTEK-57 Dimensions
A
C
D
E
F
B
VTEK-52 Dimensions
C
D
A
Frame outer
diameter
B
Grille tray outer
diameter
C
Grille protrusion
D
Mounting depth
E
Magnet width
F
Cut out hole
A
Frame outer
diameter
B
Grille tray outer
diameter
C
Grille protrusion
D
Mounting depth
4.5” • 114.3mm
5.75” • 146.05mm
.079” • 20.066mm
1.81” • 46mm
2.96” • 75.34mm
3.72” • 94.69mm
5.13” • 130.34mm
6.50” • 165mm
0.70” • 17.6mm
2.023” • 51.4mm
A
204.8mm•8.06”
112.5mm•4.42”
Frame outer
diameter
B
Grille tray outer
diameter
C
Grille protrusion
118mm•4.64”
B
B
C
D
E
F
D
Mounting depth
E
Magnet width
F
Cut out hole
8.64” x 5.51 • 219 x 140mm
6.49” • 165mm
0.89” • 22.606mm
2.32” • 59mm
3.46” • 88mm
7.20 x 5.07” • 183 x 129mm
E
Magnet width
E
F
B
F
Cut out hole
3.22” • 81.93mm
4.72 • 120mm
166.64 • 6.56”
VTEK-693 Dimensions
A
diameter
B
Frame outer
Grille tray outer
9.27” x 6.45” • 235 x 164mm
diameter
C
VTEK-62 Dimensions
A
Frame outer
diameter
B
C
D
E
F
B
Grille tray outer
diameter
C
Grille protrusion
D
Mounting depth
E
Magnet width
F
Cut out hole
6.49” 165mm •
7.07” 179.5mm •
0.94” 24mm •
2.51” 64mm •
C
4.03” • 102.29mm
5.74” 146mm •
119.28 • 4.69”
164mm•6.45”
D
Grille protrusion
D
Mounting depth
E
Magnet width
F
Cut out hole
1.42” • 36.068mm
3.75” • 95.25mm
4.33 • 110mm”
8.58” x 5.66” • 218.03 x 144mm
All specifications are subject to change without notice.