Page 1
Owner’s Manual & Warranty
2-WAY 4” COAXIAL SPEAKER
F4.0
Sound That Will Move You.
Precision
Sound Quality
The Sound That Will Move You.
Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545
Phone: 510-732-1000 Fax: 510-732-1095
MATCHED COMPONENT SET
FC5.2
MATCHED COMPONENT SET
FC6.2
2-WAY 5.25” COAXIAL SPEAKER
F5.25
2-WAY 6.5” SHALLOW COAXIAL SPEAKER
FS6.5
2-WAY 5X7” COAXIAL SPEAKER
F5x7
3-WAY 6X9” COAXIAL SPEAKER
F6x9
www.earthquakesound.com
Page 2
Table of Content
Page# 2-3…Warranty Information and Guidelines
Page# 4……Focus Component System Features, Tweeter & Crossover Specifications and
Mounting Information
Page# 5……Focus Component System Specifications & Included Items
Page# 6……Focus Coaxial Features, Specifications and Mounting Information
Page# 7……Focus Coaxial Included Items
Page# 8……Custom and Factory Replacement Guide Lines
Page# 9……Tweeter Installation
Page# 10…..Component set wiring diagram
Regarding Your Warranty:
Thank you for choosing Earthquake Sound’s line of Focus coaxial and component speakers for
superior enhancement of your vehicle’s audio system. With proper installation and responsible
listening, your Focus speakers will give you years of phenomenal listening
enjoyment.
We strongly recommend you to have your new Focus speakers installed by an authorized
Earthquake Sound dealer: Installation professionals employed by your dealer have the correct
tools and knowledge to install your speakers neatly and successfully. Also, when your new
products are installed by an authorized dealer, your product will include a FIVE YEAR LIMITED
WARRANTY. If you choose to perform your own installation, your warranty will be subject to
limitations. Over the counter authorized dealer warranties may very from one dealer to the next.
Please read the warranty information in its entirety and use good judgment when making these
vital decisions.
Warranty and Guide Lines
Five (5) year limited warranty:
Earthquake warrants the original purchaser that all Factory Sealed New Audio
Products be free from defects in material and workmanship under normal and proper use for a
period of five (5) years from the date of purchase (as shown on the original bill of sale with serial
number affixed/written on it). The five (5) year warranty period is valid only if an authorized
Earthquake dealer properly installs the product and the warranty registration card is properly
filled out and sent to Earthquake Sound Corporation. If a non-authorized party installs the
product a ninety (90) day warranty period will be applied.
(A) Five (5) years limited warranty plan coverage guidelines:
• First year: Earthquake pays for labor, parts, and ground freight (only in US mainland, not
including Alaska and Hawaii).
• Second year: Earthquake pays for labor and parts only, customer must pay freight both ways.
• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for parts and
freight both ways.
Warranty Continued
(C) Earthquake will repair or replace - at our option - all defective products/parts subject
to the following provisions:
• Defective products/parts have not been altered or repaired by other than an Earthquake
factory approved technician.
• Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged
by improper line voltage, used with incompatible products, or have its serial number or any part
of it altered, defaced or removed, or have been used in any way that is contrary to Earthquake's
written instructions.
(D) Warranty Limitations:
Warranty does not cover products that have been modified or abused. Including but not limited
to the following:
• Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper use
of cleaning materials/methods.
• Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust cap,
burnt speaker voice coil.
• Fading, deterioration of speaker components & finish due to improper exposure to elements.
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of
cleaning material.
• Burnt tracers on PCB.
• Product/part damaged due to poor packaging or abusive shipping conditions.
• Subsequent damage to other products.
A warranty claim will not be valid if the warranty registration card is not properly filled &
returned to Earthquake with a copy of the sales invoice.
(E) Service Request:
To receive product/s service, contact Earthquake service department at (510) 7321000 and request an RMA number (Return Material Authorization), items shipped without a valid
RMA number will be refused. Make sure you provide us with your complete/correct shipping
address, a valid phone number, and a brief description of the problem you are experiencing with the
product. In most cases, our technicians might be able to resolve the problem over the phone, thus
eliminating the need to ship the product.
(F) Shipping Instructions:
Product/s must be packaged in its original protective box(s) to minimize transport
damage. Shipper claims regarding items damaged in transit must be presented to carrier.
Earthquake Sound Corporation reserves the right to refuse product improperly packed. Original bill
of sale must accompany product returned for service. We encourage you to include with the
package a written description of the problem. Ship product to: Earthquake Sound Corp. 2727 Mc
Cone Avenue, Hayward, CA 94545. Ph (510) 732-1000. You are responsible for the cost of shipping
the product to Earthquake Sound Corporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from
the five (5) years limited warranty policy must be resolved according to the laws & regulations of the
county of Alameda -California.
(B) Warning:
Products (sent for repair) that are tested by Earthquake technicians and deemed to
have no problem(s) will not be covered by the five (5) year limited warranty. Customer will be
charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to
customer.
2
www.earthquakesound.com
Alternatively you may register your products online at
http://earthquakesound.com/form_reg.htm
All specifications are subject to change without notice.
3
Page 3
• Low mass poly injection cone bodies for accuracy & soundquality
• High flow ventilation stamped steel basket design
• Over hung butyl rubber surround for more bass output
• NOMEX / ROMEX spider assemblies for strong durable suspension
• Shallow mount designs for American & foreign cars and trucks
• Multiple Tweeter Mounting Configurations:
- Flush
- Surface
- Surface Angle
• Two-way passive crossover network with high-quality, low-tolerance capacitors
TWEETERS
Silk Dome With Neodymium Motor
Diameter (inches) 1-1/2
Diameter (mm) 38.1
FLUSH
Impedance 4-Ohm
Frequency Response 1kHz - 22kHz
Power Handling 40 - 175
2-1/8"
(53.975mm)
SURFACE
1-3/4"
(44.45mm)
15/16"
(23.8125mm)
15/16"
(23.8125mm)
SPECIFICATIONSFEATURES
System Model FC5.2
Diameter
Impedance
Frequency Response
Sensitivity
Power Handling
Mounting Diameter (inches)
Mounting Diameter (mm)
Mounting Depth (inches)
Mounting Depth (mm)
FC5.2 / 2-Way Component System:
3 1/2"
4 7/16"
5-1/4" (133.35mm)
4-Ohm
65Hz to 22kHz (±3dB)
87dB @ 1W/1M
80 • 150 Watts MAX
4-7/16"
112.71mm
2"
50.8mm
2 5/8"
2"
FC6.2
6-1/2" (165.1mm)
4-Ohm
55Hz to 22kHz (±3dB)
87dB @ 1W/1M
100 • 180 Watts MAX
4-15/16"
125.41mm
1-13/16"
44.5mm
• Two Focus-C5.25, 5.0-inch (127mm) poly cone woofers
• Two Focus-TW-25S, 1-inch (25mm) silk dome tweeters
• Two Focus crossover networks
• Two metal woofer grilles with trays
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Eight 8 x 1 1/2” (38.1mm) wood screws
• Eight custom installation mounting clips
• Eight 8 x 1” (25mm) sheet metal screws
• Eight factory installation mounting clips
• Two 1" (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Four speaker wire bundles with pre-attached connectors
SYSTEM CROSSOVER
- Crossover Frequency 3200Hz @ 4-Ohm
- Crossover Slope:
24dB/octave High-Pass
12dB/octave Low-Pass
- Poly Switch Tweeter Protection
1-1/2"
(38.1mm)
4
www.earthquakesound.com
4-7/8"
(123.825mm)
System Crossover Dimensions
3-1/2"
(88.9mm)
-3dB
+3dB 0dB
INPUT
WOOFER TWEETER
FC6.2 / 2-Way Component System:
2 14/16"
1 13/16"
3 6/16"
4 15/16"
All specifications are subject to change without notice.
• Two Focus-C6.5, 6 1/2" (165.1mm) poly cone woofers
• Two Focus-TW-25S, 1" (25mm) silk dome tweeters
• Two Focus crossover networks
• Two metal woofer grilles with trays
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Eight 8 x 1 1/2” (38.1mm) wood screws
• Eight custom installation mounting clips
• Eight 8 x 1” (25mm) sheet metal screws
• Eight factory installation mounting clips
• Two 1" (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Four speaker wire bundles with pre-attached connectors
5
Page 4
FEATURES
• Low mass poly injection cone bodies for accuracy & soundquality
• High flow ventilation stamped steel basket design
• Over hung butyl rubber surround for more bass output
• NOMEX / ROMEX spider assemblies for strong durable suspension
• Shallow mount designs for American & foreign cars and trucks
• Swiveling 20mm silk dome tweeters with neodymium motors
SPECIFICATIONS
Model
Diameter (inches)
Diameter (mm)
Description
Impedance
Frequency Response
Sensitivity
Power Handling
(watts)
F4.0 F5.25
4"
101.6mm
2-Way
4-Ohm
78Hz - 22kHz
86dB
35 - 70 Max
5-1/4"
133.35mm
2-Way
4-Ohm
70Hz - 22kHz
87dB
45 - 90 Max
F5x7
5" x 7"
127mm x
177.8mm
2-Way
4-Ohm
63Hz - 22kHz
88dB
65 - 130 Max
FS6.5
6-1/2"
165.1mm
2-Way
4-Ohm
55Hz - 22kHz
89dB
50 - 100 Max
F6x9
6" x 9"
152.4mm x
228.6mm
3-Way
4-Ohm
40Hz - 22kHz
90dB
150 - 300
Max
INSTALLATION
Grilles
Mounting Diameter
(inches)
Mounting Diameter
(mm)
Mounting Depth
(inches)
Mounting Depth
(mm)
The rubber magnet boot is for cosmetic purposes only. If the boot compromises mounting space,
then you may remove it.
Yes
3-10/16"
92.075mm
1-14/16"
47.625mm
Yes
4-7/16"
111.125mm
2"
50.8mm
Yes
7-3/16" x 5"
182.56mm x
127mm
2-5/16"
58.73mm
Yes
4-15/16"
125.41mm
1-13/16"
44.45mm
Yes
6" x 8-1/2"
152.4mm x
215.9mm
3-6/16"
85.725mm
F4.0 / 2-Way Speaker System:
• Two 4” poly cone woofers w/ built-in adjustable
20mm silk dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight speaker mounting clips
• Eight 1” (25mm) screws
• Two speaker wire sets with pre-attached connectors
F5.25 / 2-Way Speaker System:
• Two 5.25” poly cone woofers w/ built-in swivelling
20mm silk neodymium dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight speaker mounting clips
• Eight 1” (25mm) screws
• Two speaker wire sets with pre-attached connectors
F5x7 / 2-Way Speaker System:
• Two 5" x 7” poly cone woofers w/ built-in swivelling
20mm silk neodymium dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight speaker mounting clips
• Eight 1” (25mm) screws
• Two speaker wire sets with pre-attached connectors
FS6.5 / 2-Way Speaker System:
• Two 6.5” shallow mount poly cone woofers w/ built-in
swivelling 20mm silk neodymium dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight speaker mounting clips
• Eight 1” (25mm) screws
• Two speaker wire sets with pre-attached connectors
3"
3 10/16"
3 1/2"
4 7/16"
3 1/2"
7 3/16 x 5"
3 6/16"
4 15/16"
1 14/16"
2 1/2"
2 5/8"
2"
2 5/16"
3"
2 14/16"
1 13/16"
F6x9 / 3-Way Speaker System:
• Two 6" x 9” poly cone woofers w/ built-in swivelling
20mm silk neodymium dome tweeters and 2" high
frequency mid-range drivers
• Two matching metal woofer grilles with trays
3 6/16"
4 1/2"
• Butyl adhesive putty for woofer grilles
• Eight speaker mounting clips
• Eight 1” (25mm) screws
• Two speaker wire sets with pre-attached connectors
6
www.earthquakesound.com
All specifications are subject to change without notice.
3 1/2"
6" x 8 1/2"
7
Page 5
NOTE:
Hand tighten the screws
in a crisscross pattern to
avoid bending the speaker
INSTALLATION APPLIES
TO BOTH COMPONENT
NOTE:
AND COAXIAL SPEAKERS
INSTALLATION APPLIES
TO BOTH COMPONENT
AND COAXIAL SPEAKERS
NOTE:
basket or stripping screws.
Fasten the panel
Panel Clamp
clamp down from
behind the panel.
Top Ring
until the
secured
tweeter is
Twist on nut
MOUNTING CLIPSFACTORY CUTOUT
4 SCREWS PER SPEAKER GRILLE TRAYGRILLE
CUSTOM SPEAKER INSTALLATION
FACTORY REPLACEMENT INSTALLATION
Flush Mount Installation
Cut diameter: VTEK-25S= 2” (50.8mm)
Push assembled tweeter through cut out hole
Panel
Surface Mount Assembly & Installation
Top Ring
Flush Mount Complete assembly
Panel
Bottom Cup
Bottom Cup
Top Ring
Make sure that
the top ring and
bottom cup snap
when pushed
together
4 SCREWS PER SPEAKER SPEAKER
Bottom Cup
Angle Mount Assembly & Installation
Flush Mount Assembly
Earthquake has provided two (2)
mounting screws to be used in
the Angle and Surface options
8
www.earthquakesound.com
All specifications are subject to change without notice.
Mounting screws
Panel
9
Page 6
COMPONENT SET WIRING DIAGRAM
+
TWEETER
-
+-+
+3dB 0dB
-3dB
WOOFER TWEETER
INPUT
WOOFER
-
+
IN
-
- +
T2000W/4
AMPLIFIER
10
www.earthquakesound.com
All specifications are subject to change without notice.
11
Loading...