EarthQuake Cinénova IR16 User Manual

Sound That Will Move You.

8-ZONES MULTI-SOURCE

IR DRIVEN AMPLIFIER

USER’S MANUAL

Cinénova 16IR

Earthquake Sound Corporation
2727 McCone Avenue. Hayward, CA 94545
Phone: [phone]
Fax: [phone]
www.earthquakesound.com

IR

Table of Content

Getting Started

3

Basic Operations

Troubleshooting & Maintenance

Product Warranty

Specifications

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 - 5
6
7

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 18

Front & Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . .

Front Panel Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear Panel Map - LOCAL . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear Panel Map - BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keypad & Remote Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Features Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IR Wiring Configuration Sample . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Configuration . . . . . . . . . . . . . . . . . . . . . . . .

8
9
10
11
12
13
14
15
16

Cin ova-IR16 Power Amplifierén

Customer Support
[e-mail]
Tel: [phone]
Fax: [phone]

Safety First

This documentation contains general safety, installation, and operating instructions for the Cinénova-IR16 Amplifiers. It is
important to read this users’ manual before attempting to use these products. Pay particular attention to the safety
instructions.

Symbols Explained:

Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure –
voltage that may be sufficient to constitute a risk of shock.

Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result
in injury or death.

Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result
in damage to or destruction of part or all of the product.

Note: Calls attention to information that is essential to highlight.

The Sound That Will Move You.

Earthquake Sound Corporation
2727 McCone Avenue
Hayward, CA 94545
Tel: [phone]
Fax: [phone]

© 2008 Earthquake Sound Corporation. All rights reserved.

This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The information is subject to change without notice.
Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document.

Safety Instructions

Earthquake Sound

4

Important Safety Instructions

Cin ova-IR16 Power Amplifierén

1) Read these instructions in their entirety. 10) Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the pint

2) Store this manual and packaging in a safe place. where they exit from the apparatus.

3) Heed all warnings. 11) Only use attachments & accessories specified by the
manufacturer.

4) Follow instructions (do not take short cuts).

12) Use only compatible rack or cart for final resting position.

5) Do not use this apparatus near water.

13) Unplug this apparatus during lighting storm or when unused

6) Clean only with a dry cloth. for long period of time.

7) Do not block any ventilation openings. Install in accordance 14) Refer all servicing to qualified service personal. Servicing is

with the manufacturers instructions. required when the apparatus has been damaged in any way

such as; power-supply cord or plug is damaged, liquid has

8) Do not install near any heat sources such as radiators, heat been spilled or objects have fallen into the apparatus, the

registers, stoves, or other apparatuses that produce heat. apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with 15) To reduce the risk of fire or electric shock, do not expose
one wider that the other. A grounding-type plug has two this apparatus to rain or moisture.
blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

Safety Instructions

This triangle, which appears on your component,

alerts you to the presence of uninsulated,

dangerous voltage inside the enclosure -

voltage that may be sufficient to

constitute a risk of shock.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This triangle, which appears on your component,

alerts you to important operating and

maintenance instructions in this

accompanying literature.

5

Introduction

About Cinénova-IR16

The Cinénova-IR16 is the second generation in multi-zone that Earthquake has produced. Thanks to the feedbacks received from custom home
installers worldwide, we have managed present you with a truly powerful yet audiophile multi-zone amplifier with the following features:

!

Bridgeable output

!

Zone IR control with digital pad in each zone (included)

!

Décor friendly keypad

!

Four (4) built-in IR repeaters

!

Rear gain control limiter which limits the output gain of the zone pad.

!

Each zone has a LOCAL/BUS input audio selector

!

12V DC trigger

!

Individually driven amplifier blocks (each block is driven by a discrete complementary output class A/B stage with selected components)

!

Individual power supplies(bifilars) for power isolation, accuracy and better channel separation

There is no other multi-zone amplifier on the market with such features and power. Enjoy.

Professor Joseph J. Sahyoun
President & Chief Engineer

6

Earthquake Sound

Over the years, many of you have provided us with design requirements, new product development ideas and tremendous
feedback that helped us to improved our products. We are very grateful for your support and feedback.

From all of us here at Earthquake Sound Corporation: Thank you.

! It is recommended that the Cin

equipment be plugged into a dedicated 20-amp circuit with an
isolated ground.

! Disconnect all live power cords before making connections to the

remote gain.

! Keep all power cords away from all signal cables to prevent

humming from induced noise.

! Choose reliable signal cables cords (Earthquake Sound also

specializes in high-performance RCA cables and patches).

! All speaker wires that are ran through the walls should be twisted

type to reduce potential hum noise pick up.

! Label both ends of all wires with the corresponding room

location.

! It is best to use a grounded electrical outlet to power the

amplifier. Lack of input ground reference could be unsafe.
Consult with your electrical contractor about proper grounding.

énova-IR16 and the source

Unpacking

7

Unpacking system components

• 1 Power cord

• 8 Remote controls

• 8 Keypads (wallplates not included)

• 8 Phoenix speaker terminals

• 8 Phoenix pad connectors

• 1 16-channel Amplifier

Cinénova- 16 included componentsIR

There are several factors to consider before installing the Earthquake
Sound Cinénova-IR16 system.

• What are the intended listening zones?

• What system options and accessories might be required for
features such as local sources, etc.?

• From where in each zone will the listener prefer to control the
system? Where will the remote gains be located? Where will the
speakers be located?

• Where will the source equipment be located?

Note: The Cinénova-IR16 must have adequate ventilation above and

below for air circulation and heat dissipation. In addition, rack mount
locations may require fans and vents.

System installation considerations

Connection tips

! Keep the original carton and packing materials for future

shipment or storage.

! Check for any visual signs of damage. If you encounter any

concealed damage, consult your Earthquake Sound dealer
before proceeding with unit installation.

! Retain the sales receipt as it established the duration of the

limited warranty and provided information for insurance
purposes.

Cin ova-IR16 Power Amplifierén

Cinénova

16

IR

4

3

2

1

12

11

10

9

8

7

6

5

16

15

14

13

C to C 18.375” (466.5mm)

17” (431mm)

19” (482.6mm)

4” (101.5mm)

6.876” (174.5mm)

Front & Rear Panel Overview

8

Earthquake Sound

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

6.71” (170.5mm)

Front Panel Map

Front Panel

Cin ova-IR16 Power Amplifierén

Power/Standby Switch

This red colored LED indicates whether the amplifier is ON or OFF. When the amplifier is ON, this LED will be lit.
Note: When using the rear 12V DC Trigger (page 11 - feature 11), this front switch must be turned OFF.

Front Panel Power LED

This LED reflects the power status of the whole amplifier. Amplifier will not have any output unless this LED is ON.
Note: When using another device to turn on the Cinénova IR16 amplifier, this LED will come on when external device sends DC signal (between 5 and 28V
DC) to the back of Trigger connector (page 11 - feature 11).

Peak LED Indicators

Each LED represents one (1) channel. This particular model has sixteen (16) channels. Thus, there are sixteen (16) LEDs located on the front panel.

1

2

3

(!) Cin nova IR16 can be mounted in a standard rack mount (4 rack spaces).
(!) Mounting Dimensions: 4” center to center vertical and 18.37” center to center wide.

é

3

21

Cinénova

16

IR

4

3

2

1

12

11

10

9

8

7

6

5

16

15

14

13

9

Level Controls

This feature adjusts the maximum desired output of the associated zone to prevent overpowering of small
speakers.
Note: This knob is by-passed when its zone selector switch(feature 2) is set to BUS.

LOCAL/BUS Switch

It switches the audio source between LOCAL and common BUS. In LOCAL mode, the zone acts independently
from the rest of system by only amplifying the information fed through the associated RCA inputs. In BUS mode,
that particular zone will amplify the signal fed through the main BUS input (page 11 - feature 9).

Audio RCA Input

Individual stereo RCA inputs to drive signal into associated zones. Both RCA’s, LEFT and RIGHT, are active
when the STEREO/MONO switch is set to MONO (feature 4). Thus, you can use either RCA inputs.
Note: This RCA input also serves as an Auto Signal Sensing whenever there is a signal greater than 12mV
present.

STEREO/MONO Selector

Switches the amplifier’s output between STEREO or MONO.

· In STEREO mode, the LEFT and RIGHT outputs operate independently at 75 Watts per channel at 4Ù

speaker load. Level, Gain, Auto Turn ON and MUTE are all common to both.

· In MONO mode, the LEFT and RIGHT stereo signals are summed internally for a single high power output.

You can drive two 4Ù speakers in this mode or a single 4Ù Bridged for maximum power of 150WRMS. Also, if
the source is already a mono signal, you may use either RCA, LEFT or RIGHT.

Keypad/Zone Connector

With four (4) removable conductors (IR IN, STATUS, GROUND and CI–Control Input), these screw type
connector accepts wire sized from 24 to 12 AWG. We recommend using the CAT5, CAT5E, CAT6 or CAT6E
wires.

· IR IN – receive all types of IR signal transmitted through the Earthquake Keypad. It allows Volume up/down

and mute function at the local amplifier. Also, it allows most IR signal to pass through the four built-in IR
repeaters of the Cinénova 16IR (page 11 - feature 12).

· STATUS – this connector delivers DC signal to the Keypad’s LED status indicator when the associated

amplifier is ON.

· GROUND – for the Keypad.

· CI – Control Input is the communicator line used to control amplifier’s ON/OFF (Mute) status manually.

Fault Fuse Indicator (FFI)

This LED indicates the safe operation of the amplifier’s internal circuit for the associated zone. Under normal
condition, this LED is off. When it is lit, the fuse on the internal circuit of that associated zone is blown, usually
due to a shorted circuit. Simply replace with the same size fuse. For your convenience, we’ve included four (4)
additional fuses with every amplifier.

Speaker Terminals

This screw type connector with four (4) removable conductors accepts wire sizes from 16 to 12 AWG. Observe
the Polarity printed on the terminal. Observe the printed instruction above and below the Speaker terminal.

1

2

7

3

4

5

6

Rear Panel Map - LOCAL

1

2

3

4

5

6

7

STATUS
GROUND

IR IN

BUS

MONO

CI

FFI

0.2V3V

LEVEL

1V

BRIDGE

1

STEREO

LOCAL

FFI

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

Earthquake Sound

10

Rear Panel Map - BUS

Cin ova-IR16 Power Amplifierén

Common BUS Level Controller

This potentiometer controls the output level on all individual amplifiers that are switched to BUS mode. It also
acts as a volume limiter to protect the speakers and amplifier itself.

Common BUS Audio RCA Input

This pair of RCA drives a stereo signal into all zones that are switched to BUS mode. It allows one (1) source to
control as many as 8 zones’ audio out.

RCA Line Out

This allows the audio signal applied to the BUS RCA inputs to pass through unaltered to another device in the
system.

12V DC Trigger

It is the remote turn on option driven by a controlled 12V DC source or an AC/DC converter. The relay operating
range is between 5V DC and up to 28V DC. This remote turn on option does not override the auto signal sensing
turn on feature of this amplifier.
Note: The front power switch (page 9 - feature 1) must be left in the OFF position in order to for this function to
work.

IR Outputs

Four (4) amplified IR repeaters to repeat signals and commends fed through individual Earthquake Keypads.

Power Connection

This three (3) prong AC line connector is factory preset to 120VAC. However, other voltages are also available.

Main Power Fuse

Always replace the protection fuse with a similar value fuse. Please follow the fuse rating below:
115V, T15AL/250V
230V, T10AL/250V

8

9

10

11

12

13

14

0.2V3V

LEVEL

BUS

1V

LINE OUT

IR OUT

110-120VAC-60Hz
220-240VAC-50Hz

FUSE

1 2

4

3

+12VDC
TRIGGER

8

9

10

11

13

14

12

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

11

Keypad & Remote Map

Earthquake Sound

LED Status

This red colored LED indicates whether the amplifier is ON or OFF. When the amplifier is ON, this LED will be lit.

Volume Up/Down

This allows you to manually control the volume level up or down. The volume increases and decreases at the
same rate.
Note: This amplifier will hold the user defined volume setting for up to 3 hours from the last shut down.
Otherwise, the amplifier will start with volume position set to minimum to prevent undesired loud music in
unattended areas.

Mute

This allows you to mute or un-mute the associated amplifier(s) output.

IR Receiver

This feature allows the communication of all IR information between the Keypad and the rest of the system.
Coded signal controls the individual volume at each channel while other IR information can pass through
unaltered to the rest of the components connected to the provided IR out repeaters (page 11 - feature 12).

(!) NOTE: One Keypad is capable of driving multiple zones. Simply connect the CI wire of those zones in
parallel. For example, if you want to use the Keypad from zone 1 to control zone 1 through 5, remove the
Keypad connecting wires from zone 2 through 5 and parallel the CI wire of zone 2 through 5 to the CI of
zone 1.

(!) NOTE: If a zone is not connected to a Keypad, the speaker output will be muted (no audio output to
the speaker) unless you parallel connect that zone’s CI wire to another zone’s CI.

In addition to the eight (8) Earthquake Keypads, we also provide you with remote controls that have the same
functions – Volume Up/Down and Mute. For your convenience, the remote information can be taught to any
remote with learning capability.

Mute

This allows you to mute or un-mute the associated amplifier(s) output.

Volume Up/Down

This allows you to manually control the volume level up or down. The volume increases and decreases at the
same rate.

1

1

2

2

3

4

1

2

3

4

1

2

MUTE

VOL+

VOL-

12

Note: Wallplates are not included

ZONE

2

ZONE

3

ZONE

4

ZONE

5

KEYPAD

1

ZONE

1

ZONE

6

ZONE

7

ZONE

8

KEYPAD8KEYPAD7KEYPAD

6

Cin ova-IR16 Power Amplifierén

Special Features

Eight individual power supplies:

Rack mountable:

The Cinénova-IR16 is designed with 8 individual power
supplies(bifilar) for power isolation, accuracy and better channel This amplifier is designed to conveniently mount in commonly
separation. used racks.

Peak LED indicators: 110V AC and 220V AC selectable:

The Cinénova-IR16 is equipped with 16 LED indicators on the The Cinénova-IR16 is factory preset to 110-120VAC. However,
front panel. They show the operating status of each channel; the LEDs it can also be set to accommodate 220-240VAC by Earthquake
will illuminate when the maximum recommended output is exceeded. authorized technician(s)/dealer(s).
If an LED is illuminated the majority of the time, it indicates that the
corresponding channel is over-driven (clipped). The input to the Remote zone control:
channel must be reduced to eliminate distortion and eventually,
damages to the amplifier. Each of the eight possible zones can be controlled by a wireless

IR remote control. Each remote has the ability to control volume’s

Thermal protection: up/down level, mute and also repeat the IR signal to other sources.

Each channel is equipped with a thermal sensor designed to Bus input:
shut the amplifier down when it overheats. Overheating is not typical. It
only occurs if the amplifier is over driven with low impedance speakers, This feature simplifies installation by consolidating several
or if the amplifier is located in an improperly ventilated space. channels for one source. Simply plug the input source RCAs into the

BUS input on the unit. Then switch the input source selector to BUS for

Individually selected and matched components: as many channels are connected to the corresponding input source.

Components used to construct the Cinénova-IR16 are Bridgeable function (minimum impedance = 4-ohm):
subjected to an exhaustive selection process; during which, the
components are matched and individually tested to exact tolerance. The Cinénova-IR16 delivers up to 8-zones, and can be bridged
The multi-layer, glass-epoxy, double sided printed circuit boards into several different configurations for higher power rooms.
exceed the standard stringent requirements by 50%.

4 or 8-ohm compatible:

8-Zones: Since speakers are manufactured in several different

impedance ratings, Earthquake Sound’s Cinénova-IR16 amplifier is

The Cinénova-IR16 delivers up to 8-zones, and several other designed to be 4 and 8-Ohm compatible.
room combinations to better suite the your needs.

Special Features

13

Phoenix type connector

Should be wired using CAT5 or 5e, CAT6 or 6e.
This allows zone control via IR. This must be
connected to the zone pad.

BUS section ExplainedAmplifier section Explained

Bus Control Limiter (BCL)

It controls the front pad maximum output power
from over powering small speakers. The module
BCL would limit the output power of any amplifier
that uses the bus as a signal source.

L

R

L

R

Bus RCA input signal

Stereo input signal RCA that delivers the signal to
the bus. It also allows you do daisy chain the
signal to additional Cinénova amplifiers.

DC TRIGGER

12 Volt DC trigger to be connected to source
output 12 volt trigger. For this to operate, you need
to switch the front panel switch to OFF.

4 IR repeater

The Cinénova-IR16 has four output IR that
combine any or all zone IR input. These repeater
will repeat the sum of IR signal to control any
source input. Please note that you will need to use
your source remote, aim it at the pad and it will
deliver the IR signal to the source.

Mono/ Stereo input control

You must switch to MONO when the amplifier
is wired for MONO

L

R

Input Signal Control(ISC)

When switched to LOCAL, individual
inputs will drive each individual
amplifier.
When selecting BUS, the audio
input from the BUS will drive the
amplifier.

Speaker output terminal

For stereo applications, please follow the
polarity that is shown on top. For MONO
follow the bottom polarity.
Please note that FFI is a Fault Fuse
Indicator. Any amplifier that has the FFI
LED light on will require a fuse replacement
or possibly service.

L

M

R

-

Keypad Front view

Keypad Rear view

Rear Gain Control Limiter (RGCL)

It controls the front pad maximum output power from over
powering small speakers. The module RGCL will limit the
output only when the RCA input selection is set to MAIN
(not Bus).

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

Earthquake Sound

14

Features Explained

IR

IR
repeater

The Cinénova 16 IR allows you to connect several sources to the input stage of the amplfier. It also allows you to aim the remote
at the zone pad and use the source remote control. As you aim the remote to the pad, the IR signal is transmitted from the pad to
the amplifier and thereafter amplified. There are four repeaters on the back of the amplifier that can be connected to the source IR
sensor. Once connected, the user can control the source from the room. the illustration below has a DVD player connected to the
IR repeater. Please note that the remote in use is that of the DVD player.

Source:DVD player

Remote:DVD player

15

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

Keypad Front view

Keypad Rear view

Cin ova-IR16 Power Amplifierén

IR Wiring Configuration Sample

Earthquake Sound

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

L

M

R

SPEAKER OUTPUT

L

L

L

L

L

L

L

L

R

R

R

R

R

R

R

R

L

R

L

R

FUSE

110-120VAC-60Hz
220-240VAC-50Hz

75 Watts RMS/Per Channel

Background room(s)

6-Zones STEREO

150 Watts RMS/Per Channel

1-High Power Zones

MONO/Bridged

Recommended Configuration

16

• Number of channels

• Power rating per channel
(4-Ohm stereo), all channels driven:
(4-Ohm bridged), 8 channels:
(8-Ohm stereo), all channels driven:
(8-Ohm bridged), 8 channels:

• Frequency response:

• Total Harmonic Distortion - THD:

• Input sensitivity (for rated output power):

• Input impedance
Independent channels
Bus Input

• Signal to noise ratio:

• AUTO OFF delay time:

• Crosstalk:

• Slew rate:

• Gain:

• Damping Factor:

• Remote trigger voltage:

• Power requirement:

• Fuse ratings:
Main power fuse:
Block fuse:

• Weight
Net weight:
Gross weight:

16 Channels

75 Watts RMS

150 Watts RMS

50 Watts RMS

100 Watts RMS

20Hz - 20kHz at -0.3dB

0.01%

200mV - 3V

22 kÙ
70 kÙ

92dB

12 minutes

>86dB

50V/ìsec

29

> 200 @ 8Ù

5.5 - 28 VDC

15 Amp 120VAC 60Hz / 10 Amp 220VAC 50Hz

115V,T15A/250V / 230,T10A/250V

3 AG type, slow blow 5A/250V

61.7 lbs / 28 kg

66.1 lbs / 30 kg

Date of purchase:

Serial number:

Authorized dealer name:

Dealer’s address:

Dealer’s phone number:

_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________

( _______ ) ________ - _____________

• Dimensions
Face plate (W x D x H):
Mounting (W x H):
Chassis (W x D x H):

19” (482.6mm) x 0.47” (12mm) x 6.87” (174.5mm)

18.37” (466.5mm) x 4” (101.5mm)

16.65” (423mm) x 17” (405mm) x 6.71” (170.5mm)

Specifications

SPECIFICATIONS

FOR YOUR RECORDS

Cin ova-IR16 Power Amplifierén

17

W

F

W

M

W

C

H

F

H

C

H

M

D

C

Cin éno va

16

IR

Troubleshooting and Maintenance

Earthquake Sound

Troubleshooting

Maintenance

Humming noise from speakers.

Often humming noise is emanating from equipments that
have their ground prong broken.

a) With the amplifier OFF, unplug all RCAs connected to the
amplifier.

b) Turn on amp and listen to speakers.
If buzz has changed or reduced in level, then the problem
is coming to the amp from another source. The rest of the
hum you hear is normal and related to the fact that the
RCAs are open ended and not connected to any thing.

c) If above steps do not isolate your problem: star-ground all
components except amplifier from their chassis to the
processor.

Front LEDs are ON all the time

It is normal when running the amplifier to full power that the LEDs
flicker. If you see that the LEDs are on constantly without
flickering (solid orange) it means that the amplifier is clipping.
Reduce volume level to prevent damage to the unit.

Turn amplifier ON and circuit breaker shuts down

This can either be a short in amp or poor circuit breaker in the
house. Plug amplifier into another outlet on a different circuit
breaker with nothing connected. If the amp turns on then the
problem is with your home circuit breaker. If the amplifier still does
not power up, please call Earthquake to consult with a technician.

The following routine maintenance should be performed on a periodic
basis:

?Clean the exterior surfaces of the unit with a soft, dry, lint-free cloth.
?Do not use alcohol, benzene, acetone-based cleaners, or strong

commercial cleaners.

?Do not use a cloth made with steel wool or metal polish.
?If the unit is exposed to a dusty environment, a low-pressure

blower may be used to remove dust from its interior & exterior.

Note:
Visit www.earthquakesound.com for answers to frequently asked
questions and additional troubleshooting information.

If you are still stuck...

1. Contact an authorized Earthquake Dealer.

2. Contact Earthquake Sound Customer Service at 800-576-7944
18

Earthquake warrants the original purchaser that all Factory Sealed New Audio surround & dust cap, burnt speaker voice coil.
Products to be free from defects in material and workmanship under normal • Fading and or deterioration of speaker components & finish due to
and proper use for a period of five (5) years from the date of purchase (as shown improper exposure to elements.
on the original bill of sale with serial number affixed/written on it). The five (5) • Bent amplifier casing, damaged finish on the casing due to abuse, misuse
year warranty period is valid only if an authorized Earthquake dealer properly or improper use of cleaning material.
installs the product and the warranty registration card is properly filled out and • Burnt tracers on PCB.
sent to Earthquake Sound Corporation. If a non-authorized party installs the • Product/part damaged due to poor packaging or abusive shipping
product, a ninety (90) day warranty period will be applied. conditions.

• Subsequent damage to other products.

(A) Five (5) years limited warranty plan coverage guidelines:
warranty claim will not be valid if the warranty registration card is not

• First year: Earthquake pays for labor, parts, and ground freight (only in US properly filled & returned to Earthquake with a copy of the sales invoice.

mainland, not including Alaska and Hawaii) (shipping to us is not covered).

A

Warranty card is located on the last page of this manual.

• Second year: Earthquake pays for labor and parts only, customer must pay
freight both ways.

(E) Service Request:

• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay

for parts and freight both ways.

To receive product service, contact Earthquake service department at (510)
732-1000 and request an RMA number (Return Material Authorization). Items

(B) Warning:

shipped without a valid RMA number will be refused. Make sure you provide us
with your complete/correct shipping address, a valid phone number, and a brief

Products (sent for repair) that are tested by Earthquake technicians and

description of the problem you are experiencing with the product. In most cases,

deemed to have no problem(s) will not be covered by the five (5) year limited

our technicians might be able to resolve the problem over the phone; thus,

warranty. Customer will be charged a minimum of one (1) hour of labor (at the

eliminating the need to ship the product.

ongoing rates) plus shipping charges back to customer.

(F) Shipping Instructions:
(C) Earthquake will repair or replace - at our option - all defective
products/parts subject to the following provisions:

Product(s) must be packaged in its original protective box(es) to minimize

transport damage. Shipper claims regarding items damaged in transit must be

• Defective products/parts have not been altered or repaired by other than an

presented to carrier. Earthquake Sound Corporation reserves the right to refuse

Earthquake factory-approved technician.

improperly packed product. Original bill of sale must accompany product

• Products/parts are not subjected to negligence, misuse, improper use or

returned for service. We encourage you to include with the package a written

accident, damaged by improper line voltage, used with incompatible products

description of the problem. Ship product to: Earthquake Sound Corp. 2727

or have its serial number or any part of it altered, defaced or removed, or have

McCone Avenue, Hayward, CA 94545. Ph [phone]. You are responsible

been used in any way that is contrary to Earthquake's written instructions.

for the cost of shipping the product to Earthquake Sound Corporation.

(D) Warranty Limitations:

(G) Disputes Resolution:

Warranty does not cover products that have been modified or abused,

All disputes - between clients and Earthquake Sound Corporation - resulting
including but not limited to the following:

from the five (5) years limited warranty policy must be resolved according to the

• Damages to speaker cabinet and cabinet finish due to misuse, abuse or

laws & regulations of the county of Alameda -California.
improper use of cleaning materials/methods.

• Bent speaker frame, broken speaker connectors, holes in speaker cone,

Product Warranty

Five (5) year limited warranty

PRODUCT REGISTRATION

This Cinénova-IR16 Power Amplifier can be registered by returning the Product Registration card attached to this
manual or by visiting www.earthquakesound.com. Please also retain the bill of sale, which represents proof of
purchase and helps expedite warranty issues.

SERIAL NUMBER

We recommend that you place or write
your serial number here for future
reference, if necessary.

Cin ova-IR16 Power Amplifierén

19

Earthquake Sound reserves the right to amend details of the specifications without notice

Copyright © Earthquake Sound Corporation

Earthquake Sound Corporation | 2727 McCone Avenue. Hayward, CA 94545 | Phone: [phone] Fax: [phone]

Sound That Will Move You.