Page 1
Tan Spray Station
TS20
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
This manual contains important warnings and instructions.
Please read these instructions carefully and keep for your reference.
TM
Page 2
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART # DESCRIPTION
1 Air cap ring L0215
2 Air cap L0205
3 Spray direction plate L0206
4 Solution nozzle/spray tip L0284
5 Solution nozzle gasket L0211
6 Solution Needle L0283
7 Spring L0216
8 Solution Flow Screw L0210
9 Gland nut L0208
10 Gland seal L0272
11 Pick-up tube L0947
12 Cup gasket L0335
13 Cup (Clear) L0909
14 Twist Lock Hose assembly L0291
15 Filter L0290
Page 3
3
1. Remove all contents from box.
2. Insert end of hose to turbine.
3. Insert hose into spray gun. Push completely
in with slight pressure.
4. Fill cup with solution up to the 4 oz mark.
Use NO MORE than 2 oz per application
applied in two 1 oz coats. Follow the
“Simple Spray Gun Setup Instructions” to
properly set your spray gun up for proper
application. Turn unit on. Test the spray
pattern width on a white cotton towel.
Spray no more than 4 inches away, this
is the same distance you will use when
doing an actual application. Keep the
turbine as far away as possible from the
spray area. The turbine consumes large
volumes of air and if too close this can
cause the turbine to “inhale” the tanning
solution overspray and can cause damage
to the unit. The ON/OFF Switch is located
on the Top of the turbine unit. You will hear
a sound similar to a vacuum cleaner. You
may also notice that air is now blowing
out of the front of the spray gun. This is
correct. Air will continually flow from the
air cap of the spray gun as long as the
turbine unit is running and the air hose
is connected.
SIMPLE SPRAY GUN SETUP INSTRUCTIONS
PROPER SETUP WILL MAKE THE DIFFERENCE
BETWEEN A GREAT APPLICATION AND A
HORRIBLE APPLICATION.
1. Locate the Solution
Flow Screw on the
back of the spray gun.
Part # 8
2. Turn Clockwise to
“Close” and reduce the
spray pattern width, turn counterclockwise
to “Open” and increase spray pattern width.
3. Your goal is a 4 inch wide spray pattern
spraying 4 inches away from the client’s body.
Test on a white (light) towel until this setting
is achieved. A wider pattern will only waste
product. Spraying further away only makes
a mess and again wastes product. THIS IS
THE RECOMMENDED WAY TO SPRAY!!!!!
4. Locate the “Air Cap” (part #2) on the front of
the spray gun. This is where the solution is
sprayed out of the gun. You will see a pair of
“horns”. When these horns are in the vertical
position, you will spray up and down. When
these are in the horizontal position, you will
spray left to right.
5. Simply loosen the air cap ring (part #1) to
adjust the horns in your preferred direction.
There is no “correct” way. What works for
you is all that matters. Tighten the air cap ring
after adjustment.
Quick Tips:
Use no more than 2 oz per application. Using
more is a waste of product with no benefit.
Always do two (2) coats, 1 oz each coat. A
single heavy coat does not work as well as
two light coats.
Best developed colour results will be achieved
by waiting 8-12 hours after application before
first shower.
Apply very little to hands and feet, too much
on these areas never works!!
Your application time should take no longer
than 5 minutes; you will be able to achieve a
2-3 minute application with practice.
If you see “runs” or “beading”... you are
probably going to slow... MOVE THE GUN
FASTER OR ADJUST SOLUTION FLOW
SCREW.
Rinse your spray gun with warm water after
use, that’s all that is needed to keep your
gun clean.
SETUP AND USING YOUR TS20
HORNS IN
VERTICAL POSITION
(Spray Up and Down)
HORNS IN
HORIZONTAL POSITION
(Spray Left to Right)
Page 4
4
5. Make vertical or horizontal movements
(dependant on the direction of the air
cap part #2) over the body. KEEP THE
SPRAY GUN IN AN UPRIGHT POSITION,
DO NOT ROCK OR TIP!!!!!
Proper spraying technique
6. Do not overlap a just applied part of the
body; you need to give the solution time
to absorb into the skin. Doing so will
cause drips and runs or beading on the
skin.
7. Do one full body coverage, then start
back at the beginning and apply the
second coat.
8. After you have applied the second coat,
stand in front of a fan until dry, should
take no more than a few minutes unless
you have over applied the product.
REMEMBER, never more than 2 oz per
full body application.
9. You can shower in as little as 4 hours, for
best results wait 8-12 hours.
10. After you are done with your TS20 for the
day, simply put some tap water into the
cup and spray until clear to rinse out any
tanning solution residue.
11. On occasion, check the filter (part #15), if
it appears dirty or saturated, simply rinse
out and replace.
L1524 08/11
Earlex Ltd,
Opus Park, Moorfield Road, Guildford, Surrey, GU1 1SZ, United Kingdom
Tel: +44 (0)1483 501009 Fax: +44 (0) 1483 454548
Email: joyy@earlextanning.co.uk Web: www.earlextanning.co.uk
CONTACT YOUR DEALER FOR ALL GUARANTEE CONCERNS AND ASSISTANCE.
Loading...