Page 1
EAGTAC
High Performance Tactical Flashlight
http://www.eagletac.com
GX / MX / SX
User Manual
Models
Quick Start Guide
1) Unscrew the tailcap and remove the
battery isolation disk at the end of the
battery to use. If your ashlight does not
come with battery, insert new batteries
(w/ protrude top) to use. Ensure positive
terminals is facing the LED. Replace
tailcap and tighten snugly.
Adjusting output level
Twist the head to select between four
output levels. You can pre-select the
desired output level
before turning on
the flashlight.
Basic ON and OFF
Turn on the light by press and release
the on/o button switch (<0.4s). To turn
o the light, press and release the
switch again.
For momentary on,
press and hold
the button
switch for
immediate
output.
EAGTAC GX25L2, SX25L2 and MX25L2
models oer maximum output performance, versatile user interface, tough
build quality and rich accessories like no
other ashlight oers. This series is
designed for police, professionals, and
hobbyists.
WARNING - Lithium and Li-ion batteries
can explode or cause burns if disassembled, shorted, or exposed to high
temperature. Do not mix with used or
other battery types or install backwards.
IMPORTANT - Only use the integrated built-in
charging socket to charge the original EAGTAC
7.4V battery pack. Charging unbalanced third
party 7.4V 18650 battery pack, two individual
3.7V 18650 cells, or non-rechargeable batteries
(e.g. 3V CR123A) may result in ashlight damage.
LED (Front) Tail-cap (Back)
1st level
2nd, 3rd,
4th level
Hidden AUX. settings
With the head at tight position (1st
level), loosen to 3rd (or 4th level) and
tighten the head within one second to
enter AUX. setting. Repeat to cycle
through all settings. Turn o the light or
loosen the head to quit.
Strobe (I/II) Hi-Flash S.O.S. (I/II)
Beacon Lo-Flash
All EAGTAC ashlights are designed to
use “button-top” battery (battery with
protruding positive terminal). For
rechargeable li-ion battery, use only
EagleTac li-ion battery, or other
protected li-ion battery with compatible length and diameter. Before using
the battery, check and ensure the
battery outer wrapping (the isolating
plastic lm that wraps around the
metal housing of the battery) is complete. Broken battery wrapping may
lead to short circuit and damage to the
ashlight.
Lithium and Li-ion battery can explode
or cause burns if disassembled,
shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with dierent
brand, capacity, voltage, or install
batteries backwards. When the output
starts to dim (this implies battery is
almost drained), replace the batteries.
Do not drain the batteries completely
especially when you’re using two (or
more) batteries in series.
Battery Safety Precaution
GX25L2 SX25L2
LED
LED Lumen
ANSI Lumen
Runtime
Output/AUX level
Circuit
Batteries
Voltage
XM-L U2
1060
870
2 - 150 hrs (R22)
4 / 7
C3500 SEL
2 x18650
2.7V-12V
SST-90 N3
2700
2120
1.3 - 200 hrs (R44)
4 / 7
C9500 SEL
2 x32650
2.7V-8.4V
3 x XM-L U2
2850
2350
1.3 - 200 hrs (R44)
4 / 7
C9500 SEL
2 x32650
2.7V-8.4V
XM-L U2
1130
925
2.7 - 200 hrs (R33)
4 / 7
C4000 SEL
2 x26650
2.7V-8.4V
MX25L2 MX25L2
LED
LED Lumen
ANSI Lumen
Runtime
Output/AUX level
Circuit
Batteries
Voltage
To switch between tactical and regular
mode, turn on the ashlight at 1st level,
dial to 2nd level and then back to 1st
level for ve times within ve seconds.
Tactical Mode
100%
10%
Strobe I
Strobe II
Regular Mode
100%
35%
6%
0.1%
Level
1st
2nd
3rd
4th
Battery Isolation Disk
Page 2
Charging
For rechargeable models, use EAGTAC
model specic power DC adapter (see
below), or EAGTAC 12V automobile DC
adapter to charge. Remove the waterproof cap and insert the charging plug
to charge (store the cap next to the
charging socket). Replace the waterseal cap after charging is complete.
* If the battery is nearly drained, it may only reach to
90%+ capacity within the three hours timer due to the
“soft charging” feature for safety reasons. To reset the
timer, simply remove and re-insert the charging plug
anytime during charge.
** Since the charging circuit and LED driver share the
common output. The secondary LED may ash or light
up in very dim output when user starts up or operates
the ashlight. This is normal.
*This may or may not show in your ashlight, because
the protection board on the li-ion battery may shut o
the battery before the LED circuit picks up the battery
critical signal.
How to prolong battery life
1) Recharge often. Do not continuously
discharge the battery completely. Li-ion
batteries has no memory eect.
2) When the ashlight is going to be put
in storage for a long time, drain the
battery to under 50% capacity for best
battery life.
Our advice that you turn o the ashlight during charging for fast and full
charge. Leaving the ashlight on
during charge may pause it. The
charging circuit uses constant current
/ constant voltage method to charge
the li-ion batteries quickly and safely.
The secondary LED turns on in solid
blue color during fast charge state.
When the battery is full, the indicator
turns dim. A built-in countdown
timer* is implemented to shut o the
charging circuit within three hours.
User may remove the charger plug
shortly after the charging indicator
turns dim for immediate usage.
Battery level indicator
Reports approximate battery life for ten
seconds after changing output level or
clicking the button switch. When
battery level is very low, main LED will
ash once every 30 seconds*. Reduce
the output to extend battery runtime.
Blue
Red
Red (ash)
60%-100%
25%-60%
0%-25%
20%-100%
5%-20%
0%-5%
LED
Center
Disk
LED
Turbo output
Lower output
Secondary LED
Secondary LED** Charge status
Blue
Blue (dim)
LED o
Fast charge
Charge complete
Charging timer expire
Models
GX
SX/MX
Model specic Charger
10V 1.2A or 12V 1A
10V 1.8A or 12V 1.5A
Watt
12W
18W
Maintenance
Periodically clean the thread and o-rings
with a lint free cloth and apply a thin coating of EagleTac silicon-based lubricant to
the o-rings (not the machined thread).
Clean the battery contact, signal contact
(the silver node at the back of the head
and the plate on the body tube), thread,
and body contact (conductive aluminum
area and) with a lint free cloth and use a
small drop of Deoxit red cleaner solution
(D series) to slightly lube them for better
conductivity and smoother mode switching experience.
Color and diuser lter
For models that comes with lter
upgrade. Unscrew the stainless steel
bezel and replace it with the threaded
lter.
1) Charge your ashlight or battery
2) Ensure tailcap is tight
3) Clean all conductive contacts
(see maintenance section)
4) Check battery polarity
Troubleshooting - Flashlight does not
turn on or fails to switch between
outputs normally:
“No Hassle” EAGTAC Warranty
For repair, replacement, or other inquiries
contact your EAGTAC dealer. You can also
reach our customer support via email at
support@eagletac.com.
We warrant our ashlights to be free from
defects in workmanship and materials. We will
repair, replace at our option, without charging
any product or part which is found to be
defective under normal use within 120
months from the date of purchase with the
proof of purchase.
Electronics, chargers and rechargeable batteries are covered for a period of 12 months with
purchase receipt. Such repair or replacement
shall be the purchaser’s sole and exclusive
remedy under this warranty. Normal wear and
tear including batteries draining is not
covered, nor is damage resulting from modication, misuse, abuse, neglect, faulty battery,
battery leakage, improper maintenance or
repaired by anyone other than EAGTAC or
authorized dealer.
Do not touch or attempt to clean the
reector, as it will damage the reective
coating permanently.
*GX model shown using lter housing w/ ip-over feature.
SX and MX model uses standard individual lter add-on.
Instant Turbo output
At any output level, press and hold the
ashlight for 100% output. Release the
button to return to previous level.
Instant Strobe output
At any output level (even o), double
press and hold the on/o button switch
for strobe output. Release the button to
return to previous level.
Energy saving feature
This feature reduce output by 20%
after 200 seconds at turbo mode.
Turbo head upgrade
We oer a turbo head upgrade head
for tighter beam and brighter hot spot.
To exchange the head, un-twist the
head and replace it with the turbo
head. (Important) Ensure the LED and
LED center disc is centered inside the
reector before tightening the head,
or it may damage the LED.
“Deoxit” is a trademark of Caig Laboratories, Inc.
Periodically apply
Deoxit red here
and here
to ensure
mode switching
and output
stability in long term.
Loading...