Eago AM124ETLL Installation Manual
Installation Instruction of
AM124ETL-L
TS-series Control panel
Safety Information
1. Please read carefully and follow all instructio ns w he n op er at in g.
2. Qualified earth leakage circuit-breaker mus t be i ns ta ll ed a nd
tested with trial jump to certify the device is qualified and sa fe ty
before using the product.
3. To avoid electrical shock, the replacing of the wire must be done
by the electrical engineer or the retailer. Customer co ul d no t
replace by yourself.
4. Ground wire of massage water pump and air pump must be
connected to ground well, the minimum size copper wi re o f gr ou nd
wire must not be less than 1.5mm².
5. It is forbid to remodel, add or take part products.
6. Please don't use this product after alcohol or drugs.
7. The children shall be closely supervised by parents to use product.
8. All the electrical spare parts except the remote control m us t be p ut
suitable and stable to avoid slip into the tub.
9. Wa rn in g: t he m ix ed w at er t em pe ra tu re s ha ll n ev er e xc ee d 60
degree centigrade.
10. Don’t use sulphuric acid, hydrochloric aci d, l ye a nd o th er m ix ed
strong corrosive chemical liquid to clean produc t.
11. Th e wa te r pu mp w ou ld b e ve ry h ot w he n ru nn in g. P le as e do n’ t
touch the surface of the machine to avoid scald.
12. The water level must be higher than the jet before turning on the
product.
13. Please don’t drop anything in or insert water pu mp a nd t he
opening hole of machine.The socket position shou ld b e su it ab le .
14. War ni ng - To prevent risk of electric shock, please con ne ct t he
GFCI / RCD (earth leakage protection device) socket.
15. War ni ng - To prevent electric shock, please do not conn ec t an y
extension cord to the power supply.
16 Caution - please use the product under the follow in g co nd it io n:
water pressure is 0.15 ~ 0.40MPa, the ground must have the
ability to support the estimated load, water can not exceed the
overflow level, the washroom need to reserve enough sp ac e fo r
proper to handle the overflow of water.
17. WAR NI NG - f or b at ht ub t o be u se d no rm al ly p le as e do n ot g ra sp
the hand wheel drainer, nozzles, piping, hand ra il s, e tc ., to c au se
any leakage and other problem when unpacking t he p ro du ct .
Maintenance instruction
1. Clean the acrylic surface:
Clean acrylic surface with cotton flannel or sponge and water in daily life. If there
is scratch on the surface, please use No. 1500 water abrasive cloth polishing
slightly to clear away scratches, and then polish with toothpaste, cotton flannel.
Please don’t use strong caustic chemical liquid, such as sulphuric acid,
hydrochloric acid, lye during maintenance.
2. Plated item maintenance:
Clean the surface of plated item with cotton flannel, please don’t use coarse cloth.
3. Suction net cleaning:
Turn the screw out and take the suction net out to clean dirt, to keep the water
going through smoothly. Don’t use strong causticity chemical liquid to clean the
product, such as sulphuric, hydrochloric acid, lye and so on.
01
02
03
04
05
07-11
12
13-14
Component Struction
Water and
wire line instruction diagram
Connecting diagram of faucet pipe
Installation steps
Faucet's usage instruction
TS Control Panel
Troubleshooting
Maintenance Card
AM124ETL-L Component Struction
AM124 Water and wire line instruction diagram
No. Name No. Name
Skirt panel
Towe l ra ck
Speaker
Speaker net
1 Inch three way
One way stuff
Fitting nut
4CM conversion
Side jet
PC board
1 Inch inclined p ip e
PC board clip
Junction box
Drain
Adjustable leg
Bathtub
Wate r pu mp
Lengthened pl as ti c
Side jet
Pillow
PC board
Hand shower
Hand shower holde r
Conversion valv e
Thermostati c va lv e
Suction
Stainless steel b ra ck et
Adjustable leg
The spring base
The spring
Skirt panel cover p ad
Skirt panel cover
Bottom light
Stainless steel s tu ff
20
19
10
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
3
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
Installation Instruction 2
Loading...