SD2000
FLOOR
BURNISHER
OPERATION & PARTS MANUAL
REV A
April 2003
SPECIFICATIONS
OPERATING INSTRUCTIONS
Length: 33.75 inches
Width: 21 inches
Height: 50 inches
Weight: 69 pounds
Pad Speed: 2000
Pad Diameter: 20 inches
Drive Motor: 1.5 HP, 120V, 15A, 50/60 HZ
Power Cord: 14-3 ST, 75 feet
SAFETY
Read and understand the manual
before operating this machine.
Do not operate in explosive areas or use near
flammable liquids or gases.
Attach only to properly grounded outlet.
Do not expose to rain. Store indoors.
Do not operate the machine with a damaged cord
or plug.
Do not block or disconnect the safety lever.
Check machine for damage to cord or
plug.
Use only Hi Speed Burnishing pads
20” or 19” diameter.
To install or change the pad:
1. Unplug the machine.
2. Tip the machine back on the wheels.
3. Remove the center-lock
4. Center the pad on the pad driver.
5. Replace the center-lock and tighten securely.
To operate the machine:
1. Plug into a grounded outlet.
2. Release the handle and lower it.
3. The handle can be locked into a comfortable
position for the operator or used free floating.
4. Press the safety lever and squeeze the trigger to
start the machine.
5. Do not operate in one place as damage to the
floor could result.
6. Do not operate the machine with the handle in
upright position.
7. Remove the pad after every use.
8. Store the machine tilted back on the transport
wheels.
9. Use only new or clead pads and reverse them
as needed.
Do not leave the machine plugged in while
unattended.
Unplug the machine before servicing.
Do not put fingers under the pad or pad holder.
Unplug the machine before installing or removing
the pad.
Use only with Hi Speed Burnishing pads.
Maintenance
To maintain appearance - wipe the machine with a
damp cloth after use.
WARNING - Unplug the machine before servicing.
CHECK EVERY 250 HOURS OF USE.
1. Check the motor brushes for wear or excessive
arcing.
2. Check belt tension.
3. Check the cord and electrical system.
4. Check the safety lockout on the trigger.
5. Check wheels and bearings.
PARTS LIST
Part # Description
Fig.
1 N310122
1
N310121
1 N210102
1 N310124
1
N310118
1 N310120
1 N310119
1
N110149
1 N110163
1
N310103
1
N210105
1 N210106
1 N310125
1 N110150
1
N110115
1 N110140
1
N210109
1
N210110
1 N110146
1 N110116
1 N110159
1
N110105
1
N110171
QTY
Switch box, handle
Cover, switch box
Switch
Handle tube 7/8 x 16”
Grips
Trigger, switch
Safety lock
Spring
Clip, spring
Cord, 75’ - 14-3
Cord, handle 14-3
Grommet 3/8 ID 1
Handle, weldment
Screw 1/4-20 x 3/4
Nut, 1/4-20 Nylok
Screw 1/4-20 x 1 3/4
Wire, ground
Wire nut
Wire tie 1
Screw #6 2
Decal, Safety 1
Serial Tag
Decal, Made in USA
ILLUSTRATION
1
1
1
1
2
1
1
1
1
1
1
1
2
2
4
1
2
Fig 1
1
1
Fig.
Part # Description
2 N310102
2 N310103
2
N110155
2
N310105
2 N110145
2
N110102
2
N310109
2 N310123
2 N310134
2 N110119
2 N110120
2
N110152
2 N110123
2
N110124
2 N110126
2
N110127
2 N110125
2 N110165
QTY
Pulley, 1600 RPM
Pulley, 2000 RPM
Spacer, .75 ID
Pulley, pad drive
Spacer, pulley brgs
Bearing
Bracket, pulley mt.
Belt, 1600
Belt, 2000
Washer, flat 5/16 USS
Washer, lock 5/16 1
Bolt, 5/16-18x1” Hex
Washer, flat 3/8
Washer, lock 3/8
Bolt, 1/8-16 x 1/25
Nut, 3/8-16
Bolt, 3/8-16 x .75 4
Bolt, 3/8-16 x 1”
1
1
1
1
1
2
1
1
1
1
1
8
8
5
1
Fig 2
1
PARTS LIST
Part #
Fig.
N310101
3
3
N210101
3
N310114
3
N310112
3 N310132
3
N310115
3 N310116
3
N110144
Part # Description
Fig.
4
N310129
N110111
4
4 N110112
4 N110148
4
N310128
N310130
4
4
N110114
4
N110164
N110151
4
N110169
4
N110168
4
4
N110103
Description
Base, high speed
Motor, 1.5 HP
Wheel 5”
Wheel 4”
Axel, 1/2” x 12 3/8” 1
Axel, 1/2” x 13.875”
Axel, 1/2” x 17.25”
Caps, axel 1/2”
Handle cam lock
Bolt, adj. 5/16-18 cam
Washer, oval
Nut, 5/16-18 Nylock
Cord hook
Bracket, handle 1
Pin 1/4 x 3/4
Washer, spring 1/4”
Cap, push 1/4”
Washer, spring 3/8”
Washer, spring, 1/2”
Washer, nylon
QTY
QTY
ILLUSTRATION
1
1
2
2
1
1
6
1
1
1
2
1
1
1
1
1
7
7
Part # Description
Fig.
5 N310117
5
N210108
5 N110141
5
N110142
5
N110143
5
N310111
5 N110150
5 N110130
5 N310106
5
N110166
Cover, motor, gray
Hour meter
Screw 1/4-20 x 1”
Washer 1/4 flat
Washer 1/4 lock
Bumper
Screw 1/4-20 x 3/4
Washer, fender 1/4”
Pad driver assy.
Screw 5/16-18 x 1.25
Fig 4
QTY
1
1
4
4
4
1
1
1
1
1
Fig 5
Warranty Policy
Limited Warranty
Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and
workmanship under normal use and service to the original purchaser as detailed below.
10 Years
Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be
free from defects in materials and workmanship for a period of ten years.
3 Years
Subject to the conditions stated below, EPP warrants all automatic scrubber components to
be free from defects in materials and workmanship for a 3-year period. Parts replaced or
repaired are warranted for the remainder of the original warranty period.
1 Year
Subject to the conditions stated below, EPP warrants all other cleaning equipment
components to be free from defects in materials and workmanship for a 1-year period. Parts
replaced or repaired are warranted for the remainder of the original warranty period.
Batteries are prorated for one year.
EPP will furnish and charge for replacement parts, including transportation, to the original
owner through an EPP authorized service center. If the part is returned within 30 days and is
found defective, the owner will be credited for the cost of the replacement part including
shipping and handling.
Labor charges are covered for one year from the date of purchase if provided by an authorized
EPP service center. Travel is covered for 90 days for battery operated equipment only.
Wear items exempt from warranty include belts, carbon brushes, power cords, wheels, pad
drivers, clutch plates, brushes, pads, handle grips, filters, screens, throttle cables, and squeegees.
This warranty shall not apply to failures caused by misuse or abuse, improper
maintenance as stated in the operation manuals, use of unauthorized repair parts, repairs
by other than an EPP authorized service center, and damage in transit.
EPP disclaims and denies any liability for any direct, indirect, special incidental or consequential damage which may
be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight, or other charges
not expressly included herein.
Date Purchased:
Model Number:
Serial Number:
Please be sure to record this information. This information will be necessary for future warranty claims.
Eagle Power Products Sales and Service Provided by:
1174 Northland Drive Mendota Heights, MN 55120
651.686.5399 Fax 651.686.5695
www.eaglepower.com
Loading...