Eagle BM1220FW-120, BM1220FW-120T, BM1220FW-120-D, BM1220FW-120T-D Installation & Operating Instructions Manual
PART #361591
Suffix “-120” may be replaced with suffix “-208” for 208 volt models or suffix “-240” for 240 volt models.
Suffix “T” indicates thermostatic control.
Suffix “-D” indicates unit with drain.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
Bottom Mount Food Warmers
INSTALLATION / OPERATING INSTRUCTIONS
Models #BM1220FW-120 / -120T / -120-D / -120T-D
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING
CARRIER FOR ANY DAMAGE. SAVE YOUR BOX AND ALL PACKING MATERIALS.
This food warmer will work most efficiently when used with water in the pan liner. The hot water will give a better distribution of heat
and help keep food from drying out. It is not designed for cooking foods but merely to keep hot foods at desired temperatures for
serving.
During initial operation, a little smoke or odor may be detected. This will occur when the coating on the heating element burns
off. This should stop after 1/2 hour of operation.
This warmer is equipped with a variable control for different heat selections.
Eagle Foodservice Equipment, Eagle MHC, SpecFAB®, and Retail Display are divisions of Eagle Group. ©2009 by the Eagle Group
EG10066 Revised 02/09
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: 302/653-3000 • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: 302/653-2065
INSTALLATION INSTRUCTIONS
Parts List
# qty description
#1 6 pop rivet
#2 1 heater (1200W 120V; 1200W 240V;
#3 1 hi limit (for infinite control units)
#4 1 120V or 240V infinite control
#5 1 knob
#6 3 heat element support bracket
#7 1 heat cover assembly
#8 1 indicator light
#9 1 bowl
#10 1 recessed control panel
Replacement parts may be purchased through our
local Authorized Parts & Service Center.
1600W 240V; or 1600W 277V)
(for infinite control units),
or thermostatic control
(for thermostatic control units)
Step 1 - Cut out holes.
• Cut out and form flanged openings in countertop to fit
inside of warmer. Also, cut hole for the control panel.
• Be sure to hold to all minimum dimensions shown.
flanges
formed in
opening
Step 3 - Install unit.
• Install from underside of countertop with
control toward front.
• Attach unit to countertop with screws or
rivets (not supplied).
• Wipe off excess silicone with clean cloth
before it cures.
countertop
countertop
screw or
rivet (not
included)
unit
unit
(end view)
Step 2 - Apply silicone rubber.
Apply bead of silicone rubber to underside of
flanges formed in opening.
(Note: Silicone can be purchased at a local
hardware store.)
countertop
flanges formed
in opening
Step 4 - Attach controls.
• Remove control from recessed
control panel by removing knob
and two mounting screws.
• With indicator light still attached
to panel, insert recessed control
panel through 2
from rear of enclosure.
• Remount control to recessed
control panel and attach knob.
• Recessed control panel should
be mounted to enclosure using
screws or rivets (not supplied).
3
⁄4˝ x 51⁄8˝ cutout
screws or
rivets not
included
(4)
knob
countertop
silicone
flange formed
in opening
23⁄4˝ x 51⁄8˝
cutout
control
recessed
control panel
mounting
screws (2)
(For wiring instructions, see page 3.)
2
Loading...