DYTRAN 3225F1T DATA SHEET

Ø .250

USA

XXXX

3225F1T

MODEL 6003A03 CABLE,
LENGTH 3 FT. (INCLUDED)

.43

.215

3. CASE AND CONNECTOR MATERIAL: TITANIUM.

2. WEIGHT LESS CABLE: 0.85 GRAMS.

ARROW INDICATES SENSE AND DIRECTION OF

1

INPUT ACCELERATION FOR POSITIVE GOING
OUTPUT SIGNAL.

(+)

1

MOUNTING SURFACE
ADHESIVE MOUNT WITH CYANOACRYLATE
ADHESIVE OR DYTRAN MOUNTING WAX ­MODEL 6273

KNURLED CABLE NUT. TIGHTEN ONLY
BY HAND. DO NOT USE PLIERS TO
TIGHTEN. TO INSTALL, DO NOT
ROTATE ACCELEROMETER INTO
CABLE END BUT RATHER ROTATE
CABLE NUT.

COAXIAL CONNECTOR, DYTRAN SPECIAL
3-56 THREAD. MATES ONLY WITH MODEL
6003AXX CABLE

INSTRUMENTS, INC.

SCALE

DATE

DRAWN

APPROVED

TITLE

5X
2/22/05

N.C.

OUTLINE/INSTALLATION DRAWING,

10-32 COAXIAL CONNECTOR, JACK
(PART OF 6003A03 CABLE, INCLUDED)

ACTUAL SIZE

REV

PART NO.

MAT'LCHECKED

R.A.

NEXTASSEMBLY USEDON

DATE

A

3/30/05

MODEL 3225F1T

ECN

CHATSWORTH, CA.

N/A

DWG NO.

127-3225F1T

SHEET

OF

1

1

Dynamic Transducers and Systems

21592 Marilla St. • Chatsworth, CA 91311 • Phone [phone]
www.dytran.com • e-mail: [e-mail]

SPECIFICATIONS

MODEL 3225F1T MINIATURE LIVM ACCELEROMETER

SPECIFICATION VALUE UNITS

PHYSICAL

WEIGHT 0.85 GRAMS
SIZE (DIA x LENGTH HEX x HEIGHT) 0.25 x 0.43 x .215 INCHES
MOUNTING PROVISION Flat mounting surface for adhesive mount
CONNECTOR, RADIALLY MOUNTED [1] 3-56 JACK
CASE MATERIAL Titanium
SENSING ELEMENT TYPE Quartz, planar shear

PERFORMANCE

SENSITIVITY, ±10% [2] [3] 10.0 mV/G
RANGE F.S. FOR ± 5 VOLTS OUT ±500 G's
FREQUENCY RESPONSE, ± 10% [3] 1.6 to 10,000 Hz
MOUNTED RESONANT FREQUENCY, NOM. 40 kHz
EQUIVALENT ELECTRICAL NOISE FLOOR .007 G's RMS
AMPLITUDE NON-LINEARITY (ZERO BASED BEST-FIT ST.LINE METHOD) 2.0 % F.S., MAX.
TRANSVERSE SENSITIVITY, MAX. 5 PERCENT
STRAIN SENSITIVITY .0005 G's per microstrain @ 250/μσ

ENVIRONMENTAL

MAXIMUM VIBRATION 400 G's, RMS
MAXIMUM SHOCK 5000 G's, PEAK
TEMPERATURE RANGE -60 TO 250 °F
THERMAL COEFFICIENT OF SENSITIVITY .03 %/°F
ENVIRONMENTAL SEAL Hermetic, TIG welded & glass-to-metal seal connector

ELECTRICAL

SUPPLY CURRENT/COMPLIANCE VOLTAGE RANGE [4] 2 to 20/+18 to +30 mA/Volts
OUTPUT IMPEDANCE, TYP. 100 Ohms
BIAS VOLTAGE +7 to +9 VDC
DISCHARGE TIME CONSTANT, NOM. 0.3 Sec
OUTPUT SIGNAL POLARITY FOR ACCELERATION TOWARD TOP Positive
CASE GROUNDING Case is grounded to electrical power ground
IEPE sensor with TEDS feature per IEEE 1451.4

SUPPLIED ACCESSORIES:

(1] MODEL 6192 INSTALLATION REMOVAL WRENCH

NOTES:

[1] CONNECTOR MATES ONLY WITH DYTRAN CABLE MODEL 6003AXX (XX IS LENGTH IN FEET)
[2] MEASURED AT 100 Hz, 1 G RMS PER ISA RP37.2.
[3] ACTUAL SENSITIVITY IS GIVEN ON A CALIBRATION CERTIFICATE TRACEABLE TO NIST, SUPPLIED WITH EACH INSTRUMENT.
[4] DO NOT APPLY POWER TO THIS DEVICE WITHOUT CURRENT LIMITING, 20 mA MAX. TO DO SO WILL DESTROY THE
INTEGRAL IC AMPLIFIER.

2