DYTRAN 3053B2 DATA SHEET
S/N
ALTERNATIVE MOUNTING
METHOD USING ADHESIVE
MOUNTING BASE MODEL 6213.
3053B2
DYTRAN
.50
CONNECTOR MATES WITH
DYTRAN CABLE 6430AXX
2
USA
MOUNTING SURFACE
10-32 MOUNTING
HOLE X .150 DEEP
10-32 THREAD, TYP (REF)
.50
.53
1
3
A
A
4
1
3
2
MODEL 6200 MOUNTING STUD,
PROVIDED
SELECT SURFACE FLAT TO .OO1 TIR
MOUNTING HOLE PREPARATION
DRILL #21 (.159) DIA. X .250 DEEP
BOTTOM TAP 10-32 UNF-2B X .200
MIN. DEPTH PERF. THD.
VIEW A-A LOOKING
INTO CONNECTOR
PIN #1 SIG/PWR AXIS 1 (X)
PIN #2 SIG/PWR AXIS 2 (Y)
PIN #3 SIG/PWR AXIS 3 (Z)
PIN #4 GND RETURN,
COMMON
PINOUT
4 WEIGHT: 7.5 GRAMS.
3 XX=LENGTH IN FEET.
2. + SIGNS INDICATE SENSE AND
DIRECTION OF ACCELERATION FOR
POSITIVE OUTPUT.
1. HOUSING MATERIAL: TITANIUM ALLOY
EXCEPT AS OTHERWISE NOTED
ALL DIMENSI0NS IN INCHES
TOLERANCE: .XXX = ± .XX= ±
SURFACE FINISH
EXCEPT AS NOTED
BREAK EDGES TO DEBURR
RADIUS OR CHAMFER
THESE DIAS TO T.I.R.
FILLETS - MAX RAD.
.01.005
INSTRUMENTS, INC.
SCALE
DATE
DRAWN
APPROVED
TITLE
2X
8/7/00
N.C.
OUTLINE/INSTALLATION DRAWING,
REV
PART NO.
MAT'LCHECKED
R.A.
NEXT ASSEMBLY USED ON
DATE
-
-
MODEL 3053B2
MODEL 3053B2
ECN
CHATSWORTH, CA.
-
3053B2
DWG NO.
127-3053B2
1 1
SHEET
OF
INSTRUMENTS,
INC.
SPECIFICATIONS, MODEL 3053B2 TRIAXIAL ACCELEROMETER
SPECIFICATIONS VALUE UNITS
PHYSICAL
WEIGHT 7.5 GRAMS
SIZE (HEIGHT x WIDTH x DEPTH) 0.53 x .50 x .50 INCHES
MOUNTING [1] 10-32 TAPPED HOLE IN BASE
CONNECTOR 4-PIN [2]
MATERIAL, HOUSING/CONNECTOR TITANIUM ALLOY
PERFORMANCE
SENSITIVITY, -10 +15% [3] 10.0 mV/G
RANGE, F.S. (each axis) +/- 500 G
FREQUENCY RESPONSE, +/- 10% 2 to 5000 Hz
ELEMENT NATURAL FREQUENCY, NOM. 30 kHz
EQUIVALENT ELECTRICAL NOISE .007 G, RMS
LINEARITY [4] 1 %F.S.
TRANSVERSE SENSITIVITY, MAX, 5 %
SIGNAL POLARITY POSITIVE FOR MOTION IN DIRECTION OF ARROWS ETCHED ON HOUSING
ENVIRONMENTAL
MAXIMUM VIBRATION +/- 600 G
MAXIMUM SHOCK 5000 G
TEMPERATURE RANGE -60 to +250
ENVIRONMENTAL SEAL HERMETIC
COEFFICIENT OF THERMAL SENSITIVITY .03 %/oF
o
F
ENVIRONMENTAL
SUPPLY CURRENT RANGE, (each axis) [5] 2-to 20 mA
COMPLIANCE (SUPPLY) VOLTAGE RANGE (each axis) +18 to +30 VDC
OUTPUT IMPEDANCE, TYP. 100 OHMS
OUTPUT BIAS VOLTAGE, NOM. +10 VDC
DISCHARGE TIME CONSTANT, NOM. 0.5 SEC
GROUND ISOLATION 10 MEGOHMS (MIN)
[1] Case ground isolation is achieved by internal means.
[2] Connector mates with Dytran cable assy. Model 6430AXX. (XX = length in feet)
[3] Reference sensitivity measured at 100 Hz, 1 G RMS per ISA RP 37.2
[4] Linearity is % of specified full scale (or any lesser full scale range), zero-based best fit straight line method.
[5] Power only with Dytran LIVM power unit or other Dytran-compatible constant current type power unit. If power
is applied without current limiting protection, the internal amplifier will be immediately destroyed.
2
Loading...