Dynasty Spas SSPA-1 User Manual
SSPA-1 SPA PACK
• Single-Pump System •
This Quick Reference Card is a summary of your spa's main functions and
provides a quick overview of operations accessible from your spa side keypad.
To start the pump:
Press the Pump key to turn the pump on at low speed.
A second press will turn the pump to high speed. A third
press will turn the pump off. A built-in timer will shut the
pump off after 20 minutes unless it has been manually
deactivated.
The "Pump" indicator light will be on when the
Pump is running.
To turn the light on:
Press the Light key to turn the light on. A second press
will turn the light off. A built-in timer will shut the light off
after 2 hours unless it has been manually deactivated.
The "Light" indicator will be on when the light
is on.
To change the water temperature:
Press the Up or Down arrow key to increase or decrease
the desired water temperature. The selected temperature
setting will be displayed for 5 seconds as a confirmation.
The "Set Point" indicator light indicates that the
temperature shown is the desired, and not the
current, temperature of the water!
The temperature can be adjusted in 1-degree increments
from 59 to 104˚F (15 to 40˚C).
Water heater automatic start:
When the water temperature is 1˚F (0.5˚C) lower
than the set point, the heater will be turned on automatically until the water temperature reaches the set point
plus 1˚F (0.5˚C).
The "Heater" indicator light will be on when the
heater is on.
Note: If your system is configured in Low Current Mode,
the heater will not start if the pump is running at high speed.
"Pump" indicator light
"Light" indicator
"Heater" & "Set Point" indicator lights
Quick Reference Card
HOW TO PROGRAM THE FILTER CYCLE DURATION
The system will automatically perform two filtration cycles per day, 12 hours apart. During a filter cycle, the pump runs at low
speed for a predetermined number of hours. The ozonator is also activated. The "Filter" indicator light will be on when a filter
cycle is in progress.
To set the filter cycle duration:
Press and hold the Light key for
5 seconds. The display will show
the currently set filter cycle duration
in hours.
An irregularly flashing "Filter" indicator light indicates that
the system has stopped filtering after 3 hours because the
water temperature exceeds the set point by more than
2˚F (1˚C). If the temperature cools down to 1˚F (0.5˚C)
above set point before the scheduled end of the cycle,
filtering will resume for the remaining of the programmed
duration.
TROUBLESHOOTING
Pumps have started up for one
minute on several occasions and
"Filter Cycle" indicator is flashing.
3 flashing dots are displayed.
Water temperature is flashing.
Use the Up or Down arrow key
to change the setting.
0 = no filtration
12 = continuous filtration
Note: After a power failure, the filter cycle duration
will return to its default value (6 hours). In this case, the
first filter cycle will start 12 hours after power has been
restored.
Not a bug but a feature!
Our Smart Winter Mode protects your spa from the
cold by automatically turning pumps on for one minute
several times a day to prevent water from freezing in pipes.
A problem has been detected.
Do not enter the water! Check and open water valves.
Clean filter if necessary. Check water level. Add water
if necessary.
Shut power off and power your spa up again to reset the
system.
Call your dealer or service supplier if problem persists.
Water temperature in the spa has reached 112˚F (44˚C).
Do not enter the water! Allow water to cool down. The
system will reset automatically when water temperature
reaches 109˚F (43˚C).
Call your dealer or service supplier if problem persists.
When the desired setting is
displayed, press the Light key
to confirm. A filter cycle will start
immediately.
The display is flashing.
9919-100099-B 1.800.78.GECKO
GECKO
A power failure has occurred. Press any key to reset the
system, then reprogram all desired parameters.
E
G
C
H
T
I
W
D
E
P
P
I
U
Q
E
•
Smart
Winter
Mode
K
O
'
S
E
X
C
L
U
S
I
V
E
•
TM
Loading...