Dynasty Spas MC-MP-DY4 User Manual

MC-MP-DY4 Spa Pack
The Quick Reference Card provides a quick overview of your spa's main
functions and the operations accessible with your digital control pad.
Starting Pump 1:
Press Pump 1 to turn Pump 1 on at low speed. Pressing a second time turns Pump 1 to high speed. A third time turns Pump 1 off. When at high speed, a built-in timer turns pump off after 20 minutes and when at low speed after 2 hours, unless it has been manually deactivated.
The "Pump 1" icon lights up when Pump 1 is on at high speed. It flashes when Pump 1 is on at low speed.
Starting Pump 2:
Press Pump 2 once to turn Pump 2 on at low speed. Pressing a second time turns Pump 2 to high speed. A third time turns pump off. A built-in timer turns pump off after 20 mi­nutes, unless manually deactivated first.
The "Pump 2" icon lights up when Pump 2 is on at high speed. It flashes when Pump 2 is on at low speed.
Starting the blower:
Press Blower to turn blower on at high speed. Press a second time to turn blower to low speed. A third time turns blower off. A built-in timer turns blower off after 20 minutes, unless manually deactivated first.
The "Blower" icon lights up when blower is on at high speed. It flashes when blower is on at low speed.
Automatic water heater start:
When water temperature is 1˚F (0.5˚C) lower than the Set Point, the heater will automatically turn on until water tempera­ture reaches Set Point plus 1˚F (0.5˚C).
The "Heater" icon lights up when the heater is on. It flashes when there is a request for more heat but the heater has not yet started.
Setting water temperature:
Use Up or Down arrow key to regulate water temperature. The temperature setting will be displayed for 5 seconds to confirm your new selection.
The "Set Point" symbol indicates the desired temperature, NOT the current water temperature!
Water temperature can be adjusted by 1˚ in­crements from 59 to 104˚F (15 to 40˚C).
Inverted display:
Press and hold Pump 2 for 5 seconds to invert the display. Note that the ˚F or ˚C icon is not displayed in reverse mode. Follow the same procedure to return to default mode. If a power-up occurs, the display always returns to default mode.
Turning the light on:
Pressing Light key once turns light on at high intensity. Pressing a second time turns light to low intensity. A third time turns light off. A built-in timer turns light off after 2 hours, unless it has been manually deactivated.
The "Light" icon is displayed when light is on at high intensity. It flashes when light is on at low intensity.
Fiber Box Option: If spa has an optional fiber box only, pressing Light key turns fiber box (motor & light) on. Pressing again turns fiber box motor off but leaves light on. A third time turns both motor and light off. A built-in timer turns fiber box off after 2 hours, unless it has been manually deactivated. The "Light" icon is displayed when fiber box light is on. It flashes when fiber box motor and light are on at the same time.
LED Light Option: If spa has an optional LED light, Press Light key to turn LED lights on. To advance to the next color/display setting, press Light key twice. The LEDs will go off with the first press, then back on in the next setting with
Time & temperature display:
The display toggles every 5 seconds alternately showing the hourly time and the current water temperature.
The filter cycle is suspended if the water temperature raises more than 2˚F (1˚C) above Set Point or if a pump has been started manually. The "Filter" icon will blink (on 0.5 second, off 0.5 second, on 0.5 second, off 1.5 seconds).
the second press. If the LEDs remain off for more than 5 sec., the color/ display sequence will reset and start back at the beginning the next time the Light key is pressed. Color/ display sequences are:
1• LEDs light up and slowly cycle through all six colors. The slow cycle restarts at the beginning and repeats. 2• LEDs light up and remain on in Aqua. 3• LEDs light up and remain on in Purple. 4• LEDs light up and remain on in Blue. 5• LEDs light up and remain on in Gold. 6• LEDs light up and remain on in Green. 7• LEDs light up and remain on in Red. 8• LEDs light up for 2 sec., flash off, then flash on in the next color until all six colors have been displayed. The flashing cycle then repeats itself. 9• LEDs flash on/off quickly for a strobe light effect. A built-in timer turns lights off after 2 hours unless manually deactivated first.
The "Light" icon is displayed when light is on.
Temperature display unit:
Press and hold Light key for 5 seconds to display water temperature in either Fahrenheit (˚F) or Celsius (˚C).
Troubleshooting
Pumps have started up for one minute on several occasions and "Filter Cycle" icon is flashing.
Not a bug but a feature!
Our Smart Winter Mode protects your system from the cold by automatically turning the pumps on for one minute several times day to prevent water from freezing in pipes.
The display is flashing.
A power failure has occurred. Press any key to reset the system, then reprogram all desired parameters.
Water temperature is displayed.
Water temperature in the spa has reached 112˚F (44˚C).
Do not enter the water! Allow water to cool down. The system will reset au­tomatically when water
a
reaches 109˚F (43˚C).
Call your dealer or service supplier if problem persists.
3 flashing dots are dis­played.
A problem has been de­tected.
Do not enter the water! Check and open water valves. Clean filters if nec­essary. Check water level. Add water if needed.
Shut power off and power your spa up again to reset the system.
Call your dealer or service supplier if problem persists.
Quick Reference Card
Step Programming
Temperatur
unit
e
7
Sequence
Time of day
Step 1
Step
2
Filter cycle start time
Filter cycle duration
3
Step
Filter cycle frequency
Step
4
Economy mode start time
Step 5
Economy mode duration
Step 6
Storing settings in memory & returning to Normal mode
Step 7
Step 1- Time of day
Setting the time:
1- Enter Programming mode by holding Prog. key pressed down for 2 seconds. 2- The display will show the current time. 3- Use Up and Down arrows to change the hours. 4- Prog. key a second time to select the minutes. 5- Use Up and Down arrows to change setting.
10:25 am
11:43 pm
Steps 2 & 3- Filter cycle start time & duration
The system automatically performs two filter cycles per day, at 12-hour intervals. During the filter cycle, Pumps 1 & 2 and the blower will run the first minute, then Pump 3 will run for one minute. Pump 1 will then run at low speed for a programmed number of hours. The "Filter Cycle" icon lights up when a filter cycle is on.
To program a filter cycle, you must enter: 1) the time you want the cycle to start and 2) the duration of the cycle. If no filtering is required, the duration should be set to "0". For continuous filtering, the filter cycle duration should be set to "12:00".
Setting filter cycle start time:
1- Press Prog. key a third time. 2- The display will show FSxx, with "xx" representing the starting hour. 3- Use Up and Down arrows to change setting.
FS01
FS12
Setting filter cycle duration:
1- Press Prog. key a fourth time. 2- The display will show Fdxx, with "xx" representing the duration in hours. 3- Use Up and Down arrows to change setting.
Fd00
Fd12
Step 4- Filter cycle frequency
Setting filter cycle frequency:
1- Press Prog. key a fifth time. 2- The display will show FFxx, with "xx" representing the frequency per day. 3- Use Up and Down arrows to change setting.
FF01
FF04
Steps 5 & 6- Economy mode start time & duration*
Setting Economy mode start time:
1- Press Prog. key a sixth time. 2- The display will show ESxx, with "xx" representing the starting hour. 3- Use Up and Down arrows to change setting.
ES10
ES08
Filter Cycle
icon
Programming Mode
icon
Digital control pad lockout
This function allows you to prevent unauthorized parameter setting of the unit. This feature is especially helpful when young children have access to the keypad.
There are two modes you can choose from: Full lock or Partial lock. Full lock means that all keypad functions are locked. Partial lock means that the basic functions of the spa will remain accessi­ble (pumps, blower and light), but it will be impossible to change the temperature Set Point, to override the Economy mode or to enter the Programming mode.
When control pad is locked, the "Lock" icon will be displayed.
Locking your digital control pad:
1- Press and hold Pump 1 key for 5 seconds. 2- The display will show LocP, with "P" representing Partial lock. 3- Release the key and the keypad will be in Partial lock mode. Keep key pressed down for 5 more seconds if you want to be in Full lock mode. The "LocF" message will then be displayed.
When control pad is locked, all automatic functions of the system run as usual. If a key is pressed down, a "LocP" or "LocF" message will be displayed for 1 second. To unlock the keypad, simply press and hold Pump 1 key again for 5 seconds.
When control pad is unlocked, the "Ulock" icon will be displayed.
Press Econo key to switch from Normal mode to Economy mode. To save energy, the Economy mode Set Point is 20˚F (11˚C) below the Normal mode Set Point.
The "Economy Mode" icon lights up when Economy mode is on.
There are 3 available Economy operating modes: noEc: No Economy mode Ec 1: Economy mode always on Ec 2: Economy mode on during a programmed number of hours (see Steps 5 & 6*)
Selecting the desired Economy mode:
1- Press and hold Econo key for more than 2 seconds. 2- The display will show the current mode (noEc, Ec 1 or Ec 2). 3- Keep key pressed down until the desired mode is displayed.
After 5 seconds, the new setting will be programmed.
Heater
icon
Economy Mode
icon
LocP
LocF
Economy mode
noEc
Ec 1
Up & Down
arrows
Lock
icon
Setting Economy mode duration:
1- Press Prog. key a seventh time. 2- The display will show Edxx, with "xx" representing the duration in hours. 3- Use Up and Down arrows to change setting.
Ed01
Ed04
Step 7- Storing settings in memory
Press Prog. key an eighth time to store settings in the system's non-volatile memory and to return to Normal mode.
Summary of control panel parameters
FSxx Filter cycle start time Fdxx Filter cycle duration FFxx Filter cycle frequency ESxx Economy mode start time Edxx Economy mode duration LocX Control pad lockout
E
G
C
K
H
O
T
'
I
S
W
E
X
D
E
C
P
L
P
U
I
S
U
I
V
Q
E
Smart Winter Mode
9919-100494-B
E
TM
Loading...