Dynasty SD30, SD33, SD39, SD45, S14W User Manual

OWNER’S MANUAL AND INSTALLATION GUIDE

SD - X SERIES (Included SD30, SD33,SD39,SD45, S14W)

QUICK REFERENCE GUIDE

I. Prior to installation, please ensure:

1. The rated voltage of your heater fits the output voltage of your outlet;

2. The light bulbs in your heater is in good condition. For checking this, please follow the

instructions for replacing the light bulbs on section MAINTENANCE.

II. The heater on your electrical fireplace may emit a slight, harmless odor when first used. This odor

is a normal condition caused by the initial heating of internal heater parts and will not occur again.

III. If your heater does not emit heat, please ensure the Heater Switch is on. For further information,

please consult section Operation of the Practical User's Guide.

Marks

NOTE

Procedures and techniques, that are considered important enough to emphasize.

CAUTION

Procedures, which if not carefully followed, will result in damage to the equipment.

WARNING

Procedures, which if not carefully followed, will expose the user to the risk of serious injury, illness or
death.

A

ir outlet

50mmm 250mm

A

ir inlet

175mm

360mm

IMPORTANT INSTRUCTIONS

WARNING

You should read and always follow the important instructions below to reduce the risk of fire, electric
shock, and injury to persons.

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces, such as

surfaces near the heater outlet or light bulbs. The grill directly in front of the heater outlet becomes
hot during heater operation. If provided, use handles when moving this heater.Keep combustible
materials, such as clothes, pillows, furniture, bedding, papers and curtains at least 3 feet from the

front of the unit and keep them away from the sides and rear. Do not cover or block heater outlet
or any ventilation or exhaust opening at any time. Do not use on soft surfaces where openings may
become blocked.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the heater is left operating and unattended.

4. Do not install the heater directly on carpet or a similar surface, which may restrict air circulation
beneath the unit.

5. Always unplug heater when not in use.

6. To disconnect heater, turn controls to off, then remove plug from outlet.

7. Do not use outdoors.

8. This heater is not intended for use in wet locations, such as bathrooms, laundry areas and similar
indoor locations. Never locate heater where it may fall into water container.

9. Do not operate the heater with a damaged cord or plug, or if the heater has malfunctioned, or if the
heater has been dropped or damaged in any manner. Discard heater, or Return heater to
authorized service for examination, adjustment or repair.

10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange
cord away from traffic area and where it will not be tripped over.Do not route cord under furniture

or appliances

11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the heater.

12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.

Front view upper view

13. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to
flammable vapours.

14. Do not modify this heater. Use it only as described in this manual. Any other use not recommended
by the manufacturer may cause fire, electric shock or injury to persons.

15. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).

16. Do not burn wood or other materials in this heater.

17. Do not strike heater glass.

18. Always use a certified electrician should new circuits or outlets be required.

19. Always use properly grounded, fused and polarized outlets.

20. Always use ground fault protection where required by electrical code.

21. Always disconnect power before performing any cleaning, maintenance or relocation of the heater.