Dynapar SERIES M14 Data Sheet
SERVO DUTY
SERIES M14
Miniature Encoder
Key Features
• Ideal Economical Choice for Stepper and
Servo Motor Feedback
• Short .678” Mounting Depth and 1.5”
Diameter
• Up to 1024PPR Resolution with Index
Dynapar
™
brand
SPECIFICATIONS
STANDARD OPERATING CHARACTERISTICS
Code: Incremental, Optical
Resolution: Incremental pulses per revolution; 200
to 1024
Phasing: 90° ±18° electrical
Symmetry: 180° ±18° electrical
Index Pulse Width: 90° ±36° electrical
ELECTRICAL
Supply Voltage: 5 VDC ±10%
Supply Current: 10 mA, typ.
Output Signals: 2.5 V min. high (VOH);
0.5 V max. low (VOL). 6 mA sink/source (25°C), 4
mA (100°C)
Frequency Response: 200 kHz
Termination: 5 pin connector (accessory
connector w/12" wires,
part no. CA0060012)
Recommended Mating Connector:
Amp Part Number 103969-4
MECHANICAL
Weight: 0.22 oz (6.2 g)
Moment of Inertia: 0.16 x 10-5 oz-in-sec
(0.13 gm-cm2)
Hub Bore: 3.0, to 8.0 mm; 0.125, to 0.375
inch
Hub Dia. Tolerance: +0.0004"/-0.0000"
(+0.010 mm/-0.000 mm)
Mating Shaft Length: 0.525" (13.3 mm) max.;
0.436" (11.07 mm) min.
Mating Shaft Runout: 0.001 TIR
OUTPUT WAVEFORM AND CONNECTIONS
PIN FUNCTION CABLE WIRE
2
Mating Shaft Endplay: >512 ppr: ±0.003"
(±0.076mm); 500, 512 ppr: +0.005/-0.003"
(+0.127/-0.076mm); <500 ppr: +0.007/
-0.003" (+0.178/-0.076mm)
ENVIRONMENTAL
Operating Temperature: -20° to 100°C
Storage Temperature: -50° to 125°C
Relative Humidity: 90% non-condensing
BLACK
BLUE
WHITE
RED
3.22
BROWN
by
Dimensions/Installation
SERVO DUTY
SERIES M14
Ordering Information
To order, complete the model number with code numbers from the table below:
Code 1: Model
M14
M14 1.5" Diameter
Incremental
Modular
Encoder
IMPORTANT: To properly install Series M14, a specialized mounting kit must be purchased. Only
one kit is required to install any number of encoders with the same hub bore size.
Kit Part Number: MK M14
Example: Kit for installing encoders with 0.1248" hub Bore=
Code 2: PPR
0200/0
0400/0
0500/0
0512/0
1000/0
1024/0
Code 3: Mounting Description
0
Ordering Information
0 No mounting base
A 2x #2-56 on1.28" BC
B 3x #0-80 on 0.823" BC
C 2x #2-56 on 0.75" BC
Code 4 (from Models Table, above) designating
Hub Bore requirement.
Code 4: Hub Bore Description
3.0 3.0 mm
4.0 4.0 mm
5.0 5.0 mm
6.0 6.0 mm
8.0 8.0 mm
125 0.1248 in
187 0.1873 in
249 0.2498 in
250 0.2501 in
312 0.3123 in
374 0.3748 in
375 0.3750 in
MK M14 125
3.23
Loading...