Dynapar SERIES 60 Data Sheet
HEAVY DUTY
SERIES 60
Heavy Duty Rotopulser
Key Features
• Heavy-duty bearings with 1/2" diameter shaft
• LED optical light source
• Unbreakable disk
• Wide selection of resolutions available up to
2500 PPR
• Servo ring and face mount options
©
Dynapar
™
brand
SPECIFICATIONS
ELECTRICAL
Power Requirements: 5 to 15 VDC max.
115 mA max. plus load requirements
Frequency Response: 50 kHz
Minimum Free Path: Between any A and B
transition, will not be less than 12.5% of one full
electrical cycle. This includes effects of jitter,
phase and symmetry shifts.
Clockwise
A
B
D
C
Differential Output: 7272, 40 mA sink/source;
connections
Mating Connector: Style MS3106A-18-1S; Dynapar
Part No. MCN-N6
Single-Ended Output: 7272, 40 mA sink/source;
Mating Connector: Style MS3106A-14S-6S;
Dynapar Part No. MCN-N4
Note: Signal C (Marker) is low
for the first 180˚ of shaft
rotation clockwise (as
viewed from shaft end),
and is high for the next
180˚. Distance D equals
the minimum clear path.
ELECTRICAL CONNECTIONS
Single-Ended Output (6-pin)
#14002090010*
Function
(If Used)
Signal A
Signal B
Signal C (Marker)
+V
Common
Shield
Differential Line Driver (10-pin)
Function
(If Used)
Signal A
Signal A
Signal B
Signal B
Signal C (Marker)
Signal C
+V
Common
Shield
Not Used
*This is a mating connector/cable assembly
described in the Encoder Accessories section of
this catalog. Color-coding information is provided
here for reference.
Pin No.
Pin No.
–
–
–
MS
B
D
A
E
C
F
MS
B
G
D
H
A
I
E
C
F
J
Cable Accessory
Color Code
RED
BLUE
GREEN
WHITE
BLACK
SHIELD
#14004190010*
Cable Accessory
Color Code
RED
BLACK
BLUE
BLACK
GREEN
BLACK
WHITE
BLACK
SHIELD
MECHANICAL
Weight: 26 oz.
Speed Range: Up to 3600 RPM
Shaft Loading: Radial: 15 lbs. overhung; Axial:
5 lbs.
Inertia: 170 gm-cm
Starting Torque: 0.45 oz-in (0.30 oz-in for 1/4
in. dia. shaft)
Running Torque: 0.35 oz-in (0.15 oz-in for 1/4
in. dia. shaft)
Shaft Diameters: 1/4", 1/2" (-0.0003"/-0.0007")
2
ENVIRONMENTAL
Enclosure Rating: NEMA 12 / IP54;
Temperature Range: 0-54°C
1.36
by
Code 1: Model
Code 2: Housing
SERIES 60
Ordering Information
To order, complete the model number with code numbers from the table below:
Code 3: Shaft
Code 4: Output
Code 5: Voltage
Code 6: Pulses/Rev
HEAVY DUTY
Code 7: Wiring
Code 8: Misc
6
2 Bidirectional,
Heavy Duty
3 Bidirectional
with Marker,
Heavy Duty
DIMENSIONS
A Standard
Housing for
Single Shaft
C Standard
Housing for
Double Shaft
H Hand-Held
Housing with
Double Shaft
and two 12"
Circumference
Measuring
Wheels
inches [mm]
A 1/2" Dia, 1.0"
Len with Flat
B 1/2" Dia, 1.0"
Len without
Flat
C 1/2" Dia, 1.5"
Len with Flat
D 1/2" Dia, 1.5"
Len without
Flat
Available when Code
2 = A or C:
G 1/4" Dia, 1.0"
Len without
Flat
H 1/4" Dia, 1.0"
Len with Flat
E Single
Ended
Available when
Code 2 = A or C:
D Differen-
tial
F
F 5 to 15
VDC
0001
0002
0004
0005
0006
0010
0012
0015
0018
0020
0025
0040
0045
0050
0060
0064
0090
0096
0100
0120
0125
0127
0128
0150
0180
0192
0200
0203
0240
0250
0256
0300
0306
0315
0360
0375
0382
0384
0390
0400
0402
0430
0450
0500
0508
0512
0530
0550
0600
0625
0720
0750
0800
0805
0833
0900
1000
1024
1200
1270
1500
1800
2000
2160
2250
2400
2500
A
A MS
Connector
0 No Shaft
Seals
Available when
Code 3 = A, B,
C, or D:
B Shaft
Seals
2.625"
67.3 mm
2.000" - 1.998"
50.8 mm - 50.7 mm
MOUNTING SHOULDER
DIA.
3.500"
88.9 mm
DIA.
#5-40 x .31 (7.8 mm) DEEP – 6 HOLES
SPACED 60° – FACE SIDE ONLY
3.300" ±.005
DIA.
83.9 mm ±.127
WITHIN
.025 mm
SHAFT
DIAMETER
.45"
11.4 mm
1.000"
25.4 mm
.090" ±.005
2.3 mm ±.127
.100" ±.005
2.5 mm ±.127
.001"
3.156"
80.2 mm
DIA.
T.I.R.
.090" ±.005
2.3 mm ±.127
2.128"
54.1 mm
Hand-Held Speed Monitor
(Includes a Series 60
and dual 12" measuring
wheels)
A Series 60H hand-held speed monitor is
available as an accessory for web or roll
calibration of steel, rubber, or paper continuous
processes. These units are typically used as
accessories for occasional calibration of a
system speed, draw, or readout.
These hand-held monitors may be ordered with
any PPR from the Series 60 code table.
However, typical calibration applications with
12" measuring wheels use 60 PPR or 120 PPR,
and provide excellent calibration resolution from
zero up to full speeds. Refer to electrical
connections 6-pin chart for pin-out functions of
Series 62H.
Order Model No. 62H-AEF-_ _ _ _-AO.
1.37
Loading...