Dynamite Prophet DYNC2040 Instruction Manual

A B C D E F

G

H

I J K L

K L M N

J

I

P

O

A

F

B

C

D

G

H

E

3

Included Items

DC Power Cord (DYNC1106)
Charge Adapter: Banana to EC3 Device (2) (DYNC0072)
Charge Adapter: Banana to deans Compatible Male (2) (DYNC0056)
Banana to RX (DYNC0033)
Balancing Adapter Board :XH (2) (DYN5032)
Balancing Adapter Board: TP/FP (DYNC0101)

Optional Items

Banana to Deans insulated charge adapter: male (DYNC0053)
Banana to Traxxas® insulated charge adapter: male (DYNC0054)
Temperature Sensor (DYN5033)
Dynamite® LiPo Charge Bag: small (DYN1400), large (DYN1405)

Specifications

Input Voltage 100–240V AC (50–60Hz); 11–18V DC

Charging Capability 1–6S Li-Po/Li-Ion/Li-Fe;

1–15C Ni-Cd/Ni-MH; 2–24V Pb

Battery Capacities 50–10000 mAh

Charge Current 0.1A–6A x 4 (in 0.1A increments/50W max)

Discharge Current 0.10A–2.0A x 4 (in 0.1A increments/10W max)

Balance Current 300mA max

Balance tolerance +/- 0.01V

Operating Temperature 0ºC to + 40ºC

Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV

Protection Short-circuit, over-current, reverse polarity, low input voltage,

over-temperature

Digital Power 6A/24V max

CAUTION: Never connect the AC and DC input cords to an active power source at the same
time. This will void the warranty, cause product damage and possibly injure the user.

When Using an External DC Power Source:

1. Connect the DC power cord to the charger DC Power Input Port (B).

2. Connect the DC alligator clips to the DC power source.

3. When the charger is powered ON, a message will appear on the LCD Screen (I,J,O,P).

NOTICE: Always connect cable polarities correctly.
NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before using with

sources other than a standard AC wall outlet.

CAUTION: Before charging, always ensure you have chosen the correct battery chemistry
type for the battery you are charging.

1. Press the Esc / Mode Button to scroll through the main menu screens.

2. Press Start / Enter.

3. Press the Dec or Inc Button to scroll through the program options.

4. Press Start / Enter to select a program option.

5. Press the Dec or Inc Button to change the parameter. Press the Start / Enter Button

again to move to the next parameter.

6. Once the parameters are at the desired settings, press and hold the Start / Enter

Button for 3 seconds.

7. Press the Esc / Mode Button at any time to stop charging.

2 - LITHIUM (LI-PO/LI-FE/LI-ION) CHARGING

4 - LITHIUM STORAGE CHARGING

3 - LITHIUM DISCHARGING

WHEN Using an External AC Power Source:

1. Connect the AC power cord to the charger AC Power Input Port.

2. Connect the AC power cord to the AC power source.

3. When the charger is powered ON, a message will appear on the LCD Screen (I,J,O,P).

CONNECTING BATTERIES TO THE CHARGER:

CAUTION: Always power ON the charger before connecting a battery, or damage to the

charger and the battery can result.

1. Connect the charger to the power source.

2. Select charge port (1,2,3,4).

3. Select the charging settings.

4. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (1,2,3,4), making sure that the positive and negative connectors are not reversed.

5. Connect the battery connector to the battery adapter cable.

6. Start battery charging.

VOLTAGE SELEcTOr (E) MUST BE SET TO ThE cOrrEcT VALUE BEFOrE ThE chArGEr IS POWErED ON.

CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can
cause fire, collateral damage and injuries.

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge

programs will damage the battery or the charger.

Not to scale.
Not all wiring shown.
Not all connectors shown.

A. Power Output Ports (2,4)
B. DC Power Input Port
C. Temperature Sensor Ports (2,4)
D. Balance Circuit Adapter Board

Connectors (2,4)

E. Voltage Selector
F. Power Output Ports (1,3)
G. Temperature Sensor Ports (1,3)
H. Balance Circuit Adapter Board

Connectors (1,3)

I. Charger 1 LCD Screen
J. Charger 3 LCD Screen
K. Mode / ESC
L. Decrease
M. Increase
N. START / ENTER
O. Charger 2 LCD Screen
P. Charger 4 LCD Screen

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. If Balance Charging, connect the JST_XH balance adapter to the Balance Circuit Adapter
Board Connector of the selected charge port (D,H).

3. Connect the battery connector to the battery adapter cable.

4. If Balance Charging, connect the balance connector of the battery to the JST_XH balance
adapter.

5. Press the Esc / Mode Button to scroll through the main menu screens until you reach
Program Select=Li-Po/Li-Ion/Li-Fe.

6. Press Start / Enter.

7. Press the Esc / Mode Button at any time to stop charging.

8. Press the Dec or Inc Button to scroll through the program options (Charge, Balance Charge,
Storage, Discharge).

9. Press Start / Enter to select a program option.

10. Press the Dec or Inc Button to change the parameter. Press the Start / Enter Button again to
move to the next parameter.

11. Once the parameters are at the desired settings, press and hold the Start / Enter Button for
3 seconds.

12. The charger will check the battery and charger settings and charging will begin. The charger
will beep and display the following screen:

13. Press the Dec Button to see the rest of the Charging information.

14. Press the Inc Button to see the voltages for each cell. Press Dec to return to the charging
screen.

15. When charging is complete, the charger will sound a series of beeps.

16. Disconnect the battery from the charge adapter.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector of
the selected charge port (D,H).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the JST_XH balance adapter.

5. Press the Esc / Mode Button to scroll through the main menu screens until you reach
Program Select=Li-Po/Li-Ion/Li-Fe.

6. Press the Start / Enter Button.

7. The Dec or Inc Button until Li-Po/Li-Ion/Li-Fe STORAGE appears.

8. Press the Start / Enter Button to edit the parameter.

9. Once the parameters are at the desired settings, press and hold the Start / Enter Button for
3 seconds.

10. The charger will check the battery and charger settings and storage charging will begin.

11. Press the Dec or Inc Button to see the rest of the storage Charging information.

12. Press Esc / Mode at any time to stop charging.

13. When charging is complete, the charger will sound a series of beeps.

14. Disconnect the battery from the charge adapter.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector of

the selected charge port (D,H).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the JST_XH balance adapter.

5. Press the Esc / Mode button to scroll through the main menu screens until you reach Program

Select=Li-Po/Li-Ion/Li-Fe.

6. Press the Start / Enter Button.

7. the Dec or Inc Button until Li-Po/Li-Ion/Li-Fe DCHG appears.

8. Press the Start / Enter Button to edit the parameter.

9. Once the parameters are at the desired settings, press and hold the Start / Enter Button for
3 seconds.

10. The charger will check the battery and charger settings and discharging will begin.

11. Press the Dec or Inc Button to see the rest of the Discharging information.

12. Press Esc / Mode at any time to stop discharging.

13. When discharging is complete, the charger will sound a series of beeps.

14. Disconnect the battery from the charge adapter.

4.20 4.20 4.20

0.00 0.00 0.00

1 - SELF TEST AND PROGRAM SELECT SCREENS

When the charger is powered ON, there is a series of self tests and the screen will show the
charger brand name and model number.

ONLY LI-PO IS SHOWN IN THE FOLLOWING THREE SECTIONS. LI-ION/LI-FE
MENUS DIFFER ONLY IN CELL AND PACK VOLTAGE VALUES.

LITHIUM BATTERIES (Li-Po / Li-Fe / Li-Ion)

Ni-MH BATTERIES

Ni-Cd BATTERIES

Pb BATTERIES

DIGITAL POWER

SAVE DATA

LOAD DATA

GETTING STArTED

PrOGrAMMING qUIck GUIDE

OPErATING YOUr chArGEr

© 2015 Horizon Hobby, LLC. Dynamite, Prophet and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC.

Values in screens are for example only

PROGRAM SELECT
NiMH Battery

PROGRAM SELECT
NiCd Battery

PROGRAM SELECT
Pb Battery

PROGRAM SELECT
Memory Save

PROGRAM SELECT
Memory Load

MEMORY NiMH [1]
AUTO 1.5A

MEMORY NiMH [1]
AUTO 1.5A

PROGRAM SELECT
Digital Power

NiMH CHARGE Man
CURRENT 1.0A

NiMH CHARGE Aut
CUR LIMIT 1.0A

NiMH DISCHARGE

1.0A 12.0V

C=1.0A D=1.0A 1

NiCd CHARGE Man
CURRENT 1.0A

NiCd CHARGE Aut
CUR LIMIT 1.0A

NiCd DISCHARGE

1.0A 12.0V

C=1.0A D=1.0A 1

Pb CHARGE

0.1A 4.9V (2P)

Pb DISCHARGE

1.0A 4.9V (2P)

POWER MODE

2.0A 12.0V

NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.

DANGER: To reduce the risk of fire or electric shock, carefully follow these instructions.

NOTIcE

All instructions, warranties and other collateral documents are subject to change at the sole
discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and
click on the support tab for this product.

MEANING OF SPEcIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property
damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property
damage AND possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property
damage, collateral damage, and serious injury OR create a high probability of superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of
the product before operating. Failure to operate the product correctly can result in

damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and

requires some basic mechanical ability. Failure to operate this Product in a safe and responsible
manner could result in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not attempt disassembly, use
with incompatible components or augment product in any way without the approval of Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is
essential to read and follow all the instructions and warnings in the manual, prior to assembly,
setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

CAUTION: Always ensure the battery you are charging meets the specifications of this

charger and that the charger settings are correct. Not doing so can result in excessive
heat and other related product malfunctions, which can lead to user injury or property damage.
Please contact Horizon Hobby or an authorized retailer with compatibility questions.

WARNING: Never leave charger unattended, exceed maximum charge rate, charge with

non-approved batteries or charge batteries in the wrong mode. Failure to comply may
result in excessive heat, fire and serious injury.

chArGING WArNINGS

• NEVER LEAVE CHARGING BATTERIES UNATTENDED DURING USE.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never attempt to charge dead, damaged or wet battery packs.

• Never attempt to charge a battery pack containing different types of batteries.

• Never allow children under 14 years of age to charge battery packs.

• Never charge batteries in extremely hot or cold places or place in direct sunlight.

• Never charge a battery if the cable has been pinched or shorted.

• Never connect the charger if the power cable has been pinched or shorted.

• Never connect the charger to an automobile 12V battery while the vehicle is running.

• Never attempt to dismantle the charger or use a damaged charger.

• Never attach your charger to both an AC and a DC power source at the same time.

• Never connect the input jack (DC input) to AC power.

• Always use only rechargeable batteries designed for use with this type of charger in the correct

programming mode.

• Always inspect the battery before charging.

• Always keep the battery away from any material that could be affected by heat.

• Always monitor the charging area and have a fire extinguisher available at all times.

• Always end the charging process if the battery becomes hot to the touch or starts to change

form (swell) during the charge process.

• Always connect the charge cable to the charger first, then connect the battery to avoid short
circuit between the charge leads. Reverse the sequence when disconnecting.

• Always connect the positive red leads (+) and negative black leads (–) correctly.

• Always disconnect the battery after charging, and let the charger cool between charges.

• Always charge in a well-ventilated area.

• Always terminate all processes and contact Horizon Hobby if the product malfunctions.

• Charge only rechargeable batteries. Charging non-rechargeable batteries may cause the

batteries to burst, resulting in injury to persons and/or damage to property.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

WARNING: Failure to exercise caution while using this product and comply with the
following warnings could result in product malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

Li** BAL-CHG 6S
C= 5000mAh 5.0A

Li** CHARGE 6S
C= 5000mAh 5.0A

Li** STORAGE 6S
C= 5000mAh 5.0A

Li** DCHG 3.0

1.0A 18.0V(6S)

PROGRAM SELECT
Li** Battery

PROGRAM SELECT
Li** Battery

Prophet™ Sport Quad 4x50W AC/DC Battery Charger

Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni

DYNc2040

DYNAMITE
DYNC2040

Li** BAL-CHG 3S
C= 2200mAh 2.2A

Li** DCHG 3.0V

1.0A 9.0V(3S)

LiPo STORAGE 3S
C= 3200mAh 2.0A

Li** BAL-CHG 3S
C= 3200mAh 3.2A

F -SAFETY TIMER DEFAULT IS ON, 240MIN

Use the Safety Timer menu to set a time limit for charging a battery. When a charge cycle is
started, a clock inside the charger will begin recording the elapsed charge time. If the safety
timer function has been turned ON, the charger will stop the charging process once this
time limit has been reached to avoid damage caused by overcharging the battery. This time
value can be set between 10 and 720 minutes, in 10 minute increments.

G -CAPACITY CUT-OFF DEFAULT IS ON, 5000MAH

Use the Capacity Cut-Off menu to set a capacity limit on when the charger stops charging
a battery. When a charge cycle starts, the charger records the battery capacity. When the
capacity cutoff function is set at ON, the charger will stop charging at the capacity limit to
prevent battery damage. Capacity can be adjusted between 10 and 50,000mAh in 100mAh
increments.

H -INPUT POWER LOW CUT-OFF DEFAULT IS 11.0V

Use the Input Power Low Cut-Off menu to set the input voltage limit. An alarm will sound if
the input voltage falls below the cut-off value. The voltage alarm value can be set between

10.0 and 11.0V.

I -KEY BEEP (DEFAULT ON) / BUZZER (DEFAULT ON)

Use the Key Beep/Buzzer menu to set the key beep and charger alarm buzzer at ON or OFF
as needed. We recommend that you leave the alarm ON to alert you when charging is
complete or if there is cause for alarm during charging.

J -BACK-LIGHT

Change the Back-Light brightness by pressing the Start / Enter button and then Press the
Dec or Inc Button to change the value.

K -BATTERY END VOLTAGE

Press Start / Enter Button to select the desired battery type. Change the Default end
voltage by pressing Dec or Inc.

L -FACTORY RESET PRESS ENTER > 2S

Press the Start / Enter button for more than 2 seconds to reset all charger values to the
default values.

13 -PROGRAM SELECT – USER SET

TrOUBLEShOOTING

1. Press the Esc / Mode Button to scroll through the main menu screens until you reach Program

Select = User set.

2. Press the Start / Enter button to enter the User Set menu.

3. Press the Dec or Inc Button to scroll through the menu.

4. Press the Start / Enter Button to edit the parameter.

5. Press the Dec or Inc Button to increase or decrease the value.

6. Press the Start / Enter Button again to save the selection.

7. Press the Esc / Mode Button to return to the main menu.

A -PRE CHARGE TIME (NI-MH/NI-CD BATTERIES ONLY)

If a Ni-MH or Ni-Cd battery is fully discharged, the battery charger may not detect the
battery. The Pre-Charge Time enables you to apply a low charge rate, increasing the battery
voltage to the point where the charger detects the battery.

WARNING: Never use the Pre-Charge Time with Li-Po batteries. Doing so may cause
the battery to catch fire.

B -WAIT TIME CHG>DCHG DEFAULT IS 1 MINUTE

When you cycle a Ni-MH or Ni-Cd battery (charging, discharging and then charging again),
the battery will get very warm. The Wait Time interval between each step of the process
allows the battery to cool before starting the next step. Default time is 1 minute, but this
can be set between 0 and 60 minutes. Always allow the battery to cool to room temperature
before charging or discharging.

C -NIMH SENSITIVITY D. PEAK – DEFAULT

The D.Peak (Delta Peak) value is adjustable between 5mV/Cell and 20mV/Cell. 8mV/
Cell is a good starting point for Ni-MH batteries. If the Delta Peak value is too high, you
risk overcharging the battery; if the value is too low, charging will stop before the battery
reaches full capacity.

D -NICD SENSITIVITY D. PEAK – DEFAULT

The D.Peak (Delta Peak) value is adjustable between 5mV/Cell and 20mV/Cell. 10mV/
Cell is a good starting point for Ni-Cd batteries. If the Delta Peak value is too high, you
risk overcharging the battery; if the value is too low, charging will stop before the battery
reaches full capacity.

E -TEMP. CUT-OFF DEFAULT IS 80C/176F

The charger can be used in conjunction with a battery mounted temperature sensor (sold
separately, DYN5033) connected to the Temperature Sensor Port to monitor the temperature
of the battery during the charging process. If the battery temperature reaches the cut-off
limit, the charger will stop the charging process. Temperature values can be adjusted
between 20–80° C (68–176° F).

NiCd Sensitivity
D. Peak Default

During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger’s LCD screen, make the recommended responses. If the message continues
after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.

REVERSE POLARITY Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery.
PROCESS INTERRUPTED Make sure the power connections are correct for charging.
OUTPUT SHORT CIRCUIT Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.
INPUT VOLTAGE ERROR Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct input voltage.
CHARGER FAILURE Charger electronics require repair.
BATTERY LOW VOLTAGE Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
BATTERY HIGH VOLTAGE Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL LOW VOLTAGE Cell voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL HIGH VOLTAGE Cell voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL CONNECT ERROR Make sure the balance connection is correct for charging.
CHARGER OVERHEATING Charger temperature is too high. Power OFF the charger and let it cool.
OVER POWER Input voltage to the charger exceeded the default or adjusted input voltage setting. Make sure the power source for the charger provides the correct input voltage.
MAX CURRENT Current is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
SAFETY TIMER Maximum safe time limit has been reached.
MAX CAPACITY Maximum capacity limit has been reached.
MAX EXT. TEMP External temperature is too high. Let charger and battery cool.
CONNECTION BREAK Make sure the battery pack is connected to the charger.

9 - PB DISCHARGING

7 - NICKEL CYCLE CHARGING

8 - PB CHARGING

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Pb BATT.

4. Press the Start / Enter button.

5. Press the Dec or Inc Button until Pb DISCHARGE appears.

6. Press the Start / Enter Button to edit the parameter.

7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.

8. The charger will check the battery and charger settings and discharging will begin.

9. Press the Dec or Inc Button to see the rest of the Discharging information.

10. Press Esc / Mode at any time to stop discharging.

11. When discharging is complete, the charger will sound a series of beeps.

12. Disconnect the battery from the charger.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.

4. Press the Start / Enter button.

5. Press the Dec or Inc Button until Ni-MH/Ni-Cd DCHG>CHG appear s.

6. Press the Start / Enter Button to edit the parameter.

7. Once the parameters are at the desired settings including how many cycles (A), press and hold
the Start / Enter button for 3 seconds.

8. The charger will check the battery and charger settings and charging will begin.

9. Press the Dec or Inc Button to see the rest of the Cycle informati on.

10. Press Esc / Mode at any time to stop discharging.

11. When discharging is complete, the charger will sound a series of beeps.

12. Disconnect the battery from the charger.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Pb BATT.

4. Press the Start / Enter button.

5. Press the Dec or Inc Button until Pb CHARGE appears.

6. Press the Start / Enter Button to edit the parameter.

7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.

8. The charger will check the battery and charger settings and charging will begin.

9. Press the Dec or Inc Button to see the rest of the charging inform ation.

10. Press Esc / Mode at any time to stop discharging.

11. When charging is complete, the charger will sound a series of beeps.

12. Disconnect the battery from the charger.

CAUTION: The Pb charge program menus are to be used ONLY for the charging and
discharging of Pb battery packs. Charging other battery types using the Pb charge
programs will damage the battery or the charger.

10 - DIGITAL POWER

11 - MEMORY SAVE

12 - LOAD DATA

The Digital Power menu enables you to use the Prophet Sport Quad charger as a power supply for
external devices. The maximum Digital Power output for this charger is 6A / 24V.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Press the Esc / Mode Button to scroll through the main menu screens until you reach Digital
Power.

3. Press the Start / Enter Button to edit the parameter.

4. Once the parameters are at the desired settings, press and hold the Start / Enter Button for 3
seconds.

5. Press the Esc / Mode Button at any time to stop supplying power to the external device.

6. Disconnect the external device from the charger.

The Memory Save menu option enables you to save 10 (x4) battery charging profiles that you use
most often.

1. Press the Esc / Mode Button to scroll through the main menu screens until you reach

Program Select - Memory Save.

2. Press the Start / Enter Button to enter the Memory Save menu. The first time you enter the

menu, the “0” model memory location flashes.

3. Press the Dec or Inc Button to select a memory location (0-9), then press and hold the

Start / Enter Button to save the selection. The BATT TYPE screen appears.

4. Press the Dec or Inc Button to select the desired battery type, then press the Start / Enter

Button.

5. Press the Inc Button to adjust the parameters for Balance Charge, Cycle, Storage, etc.

6. Press and hold the Start / Enter Button for 3 seconds to save your selections. The charger

screen displays “Saving..”, then returns to the Memory Save screen.

The Load Data menu option enables you to access the 10 battery charging profiles that you stored
in the Save Data menu.

1. Press the Esc / Mode Button to scroll through the main menu screens until you reach

Program Select - Load Data.

2. Press the Start / Enter Button to enter the Load Data menu. The first time you enter the

menu, the “0” model memory location flashes.

3. Press the Dec or Inc Button to select a memory location (0-9).

4. Press the Start / Enter Button for 3 seconds until the Charge screen appears.

5. Press the Dec or Inc Button to scroll through Charge, Balance Charge, Cycle, Discharge,

Storage, etc.

6. Press and hold the Start / Enter Button for 3 seconds to load the desired function.

5 - NICKEL (NI-MH/NI-CD) CHARGING

6 - NICKEL DISCHARGING

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Esc / Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.

4. Press the Start / Enter button.

5. Press the Dec or Inc Button until Ni-MH/Ni-Cd CHARGE appears.

6. Press the Start / Enter Button to edit the parameter.

7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.

8. The charger will check the battery and charger settings and charging will begin.

9. Press the Dec or Inc Button to see the rest of the Discharging information.

10. Press Esc / Mode at any time to stop discharging.

11. When discharging is complete, the charger will sound a series of beeps.

12. Disconnect the battery from the charge adapter.

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the battery connector to the battery adapter cable.

3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.

4. Press the Start / Enter button.

5. Press the Dec or Inc Button until Ni-MH/Ni-Cd DISCHARGE appears.

6. Press the Start / Enter Button to edit the parameter.

7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.

8. The charger will check the battery and charger settings and charging will begin.

9. Press the Dec or Inc Button to see the rest of the Discharging information.

10. Press Esc / Mode at any time to stop discharging.

11. When discharging is complete, the charger will sound a series of beeps.

12. Disconnect the battery from the charger.

ONLY NI-MH IS SHOWN IN THE FOLLOWING THREE SECTIONS.

© 2015 Horizon Hobby, LLC. Dynamite, Prophet and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC. Created 08/2015 | 48543

What this Warranty Covers - Horizon Hobby, LLC (Horizon) warrants to the original purchaser that
the product purchased (the “Product”) will be free from defects in materials and workmanship at
the date of purchase.

What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic dam­age, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due
to improper use, installation, operation or maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center,
(v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with ap­plicable technical regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABIL­ITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF
THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon
to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WAR­RANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEG­LIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon
exceed the individual price of the Product on which liability is asserted. As Horizon has no control
over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted
for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all result­ing liability. If you as the purchaser or user are not prepared to accept the liability associated with
the use of the Product, purchaser is advised to return the Product immediately in new and unused
condition to the place of purchase.

Law - These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot

provide warranty support or service. Once assembly, setup or use of the Product has been started,
you must contact your local distributor or Horizon directly. This will enable Horizon to better answer
your questions and service you in the event that you may need any assistance. For questions or
assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry

at https://horizonhobby.quickbase.com/db/bghj7ey8c?a=GenNewRecord, or call the toll free tele­phone number referenced in the Warranty and Service Contact Information section to speak with a
Product Support representative.

Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes may be
included, but are not designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request
is available at http://www.horizonhobby.com/content/_service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon, you will be asked
to provide your complete name, street address, email address and phone number where you can
be reached during business hours. When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po
battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements - For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been

met, your Product will be serviced or replaced free of charge. Service or replacement decisions are
at the sole discretion of Horizon.

Non-Warranty Service - Should your service not be covered by warranty, service will be
completed and payment will be required without notification or estimate of the expense
unless the expense exceeds 50% of the retail purchase cost. By submitting the item for ser-

vice you are agreeing to payment of the service without notification. Service estimates are available
upon request. You must include this request with your item submitted for service. Non-warranty
service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American
Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Hori­zon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/_service­center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use

and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon
will hold non-compliant Product for a period of 60 days from notification, after which it
will be discarded.

LIMITED WArrANTY

WArrANTY AND SErVIcE cONTAcT INFOrMATION

PROGRAM SELECT
NiMH Battery

PROGRAM SELECT
Pb Battery

PROGRAM SELECT
Digital Power

PROGRAM SELECT
Memory Save

MEMORY NiMH [1]
AUTO 1.5A

MEMORY NiMH [1]
AUTO 1.5A

PROGRAM SELECT
Memory Load

PROGRAM SELECT
User Set =>

Temp. Cut-off
ON 80C(176F)

Factory reset
Press Enter > 2S

NiMH CHARGE Man
CURRENT 1.0A

NiMH DISCHARGE

1.0A 12.0V

C=1.0A D=1.0A 1

Pb CHARGE

0.1A 4.9V (2P)

Pb DISCHARGE

1.0A 4.9V (2P)

Wait Time
CHG>DCHG 5min

NiMH Sensitivity
D. Peak Default

Capacity Cut-Off
ON/OFF 5000mAh

Key Beep ON/OFF
Buzzer ON/OFF

PreCharge Time
ON/Off 1min

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.

Back–light

100%

Battery end volt
LiPo 4.20V/C

Safety Timer
ON/OFF 240min

Input Power Low
Cut-Off 11.0V

A

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

www.quickbase.com/db/

bghj7ey8c?a=GenNewRecord

888-959-2306

Sales

[e-mail]

888-959-2306

United Kingdom

Service/Parts/Sales:

Horizon Hobby Limited

[e-mail]

Units 1–4, Ployters Rd, Staple Tye

Harlow, Essex, CM18 7NS, United Kingdom

[phone]

Germany

Horizon Technischer Service [e-mail]

Christian-Junge-Straße 1
25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH [phone]

France

Service/Parts/Sales:

Horizon Hobby SAS

[e-mail]

11 Rue Georges Charpak

77127 Lieusaint, France

[phone]

China

Service/Parts/Sales:

Horizon Hobby – China

[e-mail]

Room 506, No. 97 Changshou Rd.

Shanghai, China 200060

[phone]

cOMPLIANcE INFOrMATION FOr ThE EUrOPEAN UNION

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive
2004/108/EC and Low Voltage Directive 2006/95/EC. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for
the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or where you purchased the product.

Prophet™ Sport Quad 4x50W AC/DC Battery Charger

Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni

A B C D E F

G

H

I J K L

K L M N

J

I

P

O

A

F

B

C

D

G

H

E

3

Im Lieferumfang enthalten:

DC Anschlusskabel: (DYNC1106)
Ladestecker Banane auf EC3 Stecker (2) (DYNC0072)
Ladestecker Banane auf Deans Stecker (2) (DYNC0056)
Ladekabel RX (DYNC0033)
Balancer Adapter Board XH (2) (DYN5032)
Balancer Adapter Board TP / FP (DYNC0101)

Optionales Zubehör:

Ladestecker Banane auf Deans kompatibler Stecker (DYNC0053)
Ladestecker Banane auf TRA Stecker (DYNC0054)
Temperatursensor (DYN5033)
Dynamite LiPoCharge Protection Bag klein (DYN1400), gross (DYN1405)

Spezifikationen

Eingangsspannung 100–240V AC (50–60Hz); 11–18V DC

Ladekapazität 1–6S Li-Po/Li-Ion/Li-Fe;

1–15C Ni-Cd/Ni-MH; 2–24V Pb

Akku Kapazitäten 50–10000 mAh

Ladestrom 0.1A–6A x 4 (in 0.1A Schritten /50W max)

Entladestrom 0,10A–2.0A x 4 (in 0.1A Schritten /10W max)

Balancestrom 300mA max
Balancetoleranz +/- 0.01V
Betriebsbereich 0ºC to + 40ºC

Lademodes Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Blei-Gel CC/CV

Schutz Kurzschluss, Überstrom, Verpolung, niedrige Eingangsspannung,

Übertemperatur

Leistung digital 6A/24V max

ACHTUNG: Schließen Sie nie gleichzeitig den AC und DC Stromeingang an die
Stromquellen an. Das Gerät wird dabei beschädigt und mögliche Personenschäden sind die
Folge. Dieses ist nicht durch die Garantie gedeckt.

Bei Verwendung einer externen DC Stromquelle:

1. Schließen Sie das DC Anschlusskabel an den DC Stromeingang (B) an.

2. Schließen Sie die Krokodilklemmen an die DC Stromquelle an.

3. Wird das Ladegerät eingeschaltet erscheint eine Meldung auf dem LCD Display (I,J,OP).

HINWEIS: Verbinden Sie die Polarität stets richtig.
HINWEIS: Bitte lesen Sie alle Begleitinformationen der 12 Volt Batterie oder kontakten den technischen

Service von Horizon Hobby bevor Sie eine andere Stromquelle als den AC Netzstrom verwenden.

ACHTUNG: Prüfen Sie vor dem Laden immer ob Sie für den zu ladenden Akku den
richtigen Akkutyp gewählt haben.

1. Drücken Sie den Esc / Mode Button um durch das Hauptmenü zu blättern.

2. Drücken Sie Start / Enter.

3. Drücken Sie den Dec or Inc Button um durch die Programmoptionen zu blättern.

4. Drücken Sie Start / Enter Button um eine Programmoption zu wählen.

5. Drücken Sie den Dec oder Inc Button um einen Parameter zu ändern. Drücken Sie
den Start / Enter Button erneut um zum nächsten Parameter zu wechseln.

6. Sind alle Parameter wie gewünscht eingestellt, drücken und halten Sie den Start/
Enter Button für drei Sekunden.

7. Drücken Sie den ESC / Mode Button zu jedem beliebigen Zeitpunkt um den
Ladevorgang zu stoppen.

2 - LADEN VON LITHIUM (LI-PO/LI-FE/LIION) AKKUS

4 - EINLAGERUNGSLADUNG VON LITHIUM AKKUS

3 - ENTLADEN VON LITHIUM AKKUS

BEI VERWENDUNG EINER EXTERNEN AC STROMQUELLE:

1. Schließen Sie den Netzstecker an den AC Netzeingang des Ladegerätes an.

2. Schließen Sie das Netzkabel an die Netzsteckdose an.

3. Wird das Ladegerät eingeschaltet erscheint eine Meldung auf dem LCD Display (I,J,OP).

ANSCHLUSS VON AKKUS AN DAS LADEGERÄT:

ACHTUNG: Schalten Sie immer das Ladegerät ein bevor Sie einen Akku an das

Ladegerät anschließen, da sonst das Ladegerät und der Akku beschädigt werden kann.

1. Schließen Sie das Ladegerät an eine Stromquelle an.

2. Wählen Sie den Ladeanschluss (1,2,3,4).

3. Überprüfen Sie die Einstellungen des Ladegerätes.

4. Schließen Sie die Bananenstecker des Ladekabels an die Ladebuchsen des gewählten
Ladeports (1,2,3,4) und stellen sicher dass Sie die positiven und negativen Anschlüsse nicht
vertauschen.

5. Schließen Sie den Akkuanschluss an den Ladestecker an.

6. Starten Batterieladung.

VOr DEM EINSchALTEN MUSS DEr SPANNUNGSWAhLSchALTEr (E) AUF DIE kOrrEkTE
ETzSPANNUNG GESTELLT WErDEN.

ACHTUNG: Sollte zu einem beliebigen Zeitpunkt des Ladevorgangs der Akku heiß werden und / oder anschwellen, trennen Sie den Akku unverzüglich und beenden den Ladevorgang. Der
Akku könnte Feuer fangen was zu Sach- und Personenschäden führen kann.

ACHTUNG: Das Verwenden eines zum Akku nicht kompatiblen Ladestromes kann zu Schäden oder Fehlfunktionen des Ladegerätes oder Akkus führen.

ACHTUNG: Das Lithiumprogramm ist ausschließlich zum Laden oder Entladen von Lithium Akkus geeignet. Das Laden von anderen Akkus mit diesem Programm beschädigt den Akku oder

das Ladegerät.

Abbildung nicht
maßstabgerecht.

Vollständige Verkabelung
nicht dargestellt.

Vollständige Anschlüsse
nicht dargestellt.

A. Ladeanschlüsse
B. DC Stromeingang
C. Anschlüsse Temperatursensor
D. Balanceboard Adapteranschlüsse (2,4)
E. Spannungsschalter
F. Ladestecker
G. Anschlüsse Temperatursensor (1,3)
H. Balanceboard Adapteranschlüsse (2,4)

I. LCD Display Lader 1
J. Charger 3 LCD Screen
K. LCD Display Lader 3
L. Verringern (Decrease)
M. Erhöhen (Increase)
N. START / ENTER
O. LCD Display Lader 2
P. LCD Display Lader 2

1. Schließen Sie die Bananenstecker an die Ladebuchsen des gewählten Ladeports (A,F) an.
Bitte achten Sie darauf die positiven und negativen Anschlüsse nicht zu verpolen.

2. Schließen Sie bei dem balancierten Laden (Balance Charging) den JST-XH Balance Adapter an
den Balanceboardanschluss (D,H) des gewählten Ladeanschluss an.

3. Schließen Sie den Akkuanschluss an das Ladekabel an.

4. Schließen Sie den Balanceranschluss des Akkus an den JST_XH Balanceadapter an.

5. 5. Drücken Sie den ESC /Mode Button um durch die Hauptmenüs zu scrollen bis die Anzeige
Program Select=Li-Po/Li-Ion/Li-Fe. erreicht haben.

6. Drücken Sie Start Enter.

7. Drücken Sie zu einem beliebigen Zeitpunkt den ESC /Mode Button um den Ladevorgang u
stoppen.

8. Drücken Sie den Dec oder Inc Button um durch die verschiedenen Programmoptionen Charge
(Laden), Balance Charge (Balanciertes Laden) , Storage (Einlagern) und Discharge (Entladen)
zu wählen.

9. Drücken Sie Start /Enter um die Programmauswahl zu wählen.

10. Drücken Sie den Dec oder Inc Button um die Parameter zu wechseln. Drücken Sie den Start /
Enter Button erneut um zum nächsten Parameter zu gelangen.

11. Haben Sie die gewünschten Parameter eingestellt drücken und halten Sie den Start/ Enter
Button für drei Sekunden.

12. Das Ladegerät prüft den Akku und die Einstellungen und der Ladevorgang beginnt. Das
Ladegerät piept und zeigt folgende Anzeige:

13. Drücken Sie den Dec Button um die Ladeinformation zurück zu stellen.

14. Drücken Sie den Inc Button um die Spannungsinformation der einzelenen Zellen abzurufen.
Drücken Sie den Dec Button um wieder in das Lademenü zu wechseln.

15. Ist der Ladevorgang beendet ertönt eine Serie von Pieptönen.

16. Trennen Sie den Akku vom Ladestecker.

1. Schließen Sie die Bananenstecker an die Ladebuchsen des gewählten Ladeports (A,F) an.
Bitte achten Sie darauf die positiven und negativen Anschlüsse nicht zu verpolen.

2. Schließen Sie den JST-XH Balance Adapter an den Balanceboardanschluss (D,H) des gewählten
Ladeanschluss an.

3. Schließen Sie den Akkuanschluss an das Ladekabel an.

4. Schließen Sie den Balanceranschluss des Akkus an den JST_XH Balanceadapter an.

5. Drücken Sie den ESC /Mode Button um durch die Hauptmenüs zu scrollen bis Sie die Anzeige
Program Select=Li-Po/Li-Ion/Li-Fe erreicht haben.

6. Drücken Sie Start / Enter.

7. Drücken Sie den Dec oder Inc Button bis die Anzeige Li-Po/Li-Ion/Li-Fe Storage (Storage =
Einlagerungsladung) erscheint.

8. Drücken Sie den Start / Enter Button um die Parameter einzustellen.

9. Haben Sie die Parameter wie gewünscht eingestellt, drücken und halten Sie den Start / Enter
Button für drei Sekunden.

10. Das Ladegerät prüft den Akku und die Einstellungen und der Entladevorgang beginnt.

11. Drücken Sie den Dec oder Inc Button um die weiteren Entladeinformation zu sehen.

12. Drücken Sie den ESC / Mode Button um den Entladevorgang zu einem beliebigen Zeitpunkt zu
beenden.

13. Ist der Entladevorgang beendet ertönt eine Tonserie.

14. Trennen Sie den Akku vom Ladeadapter.

1. Schließen Sie die Bananenstecker an die Ladebuchsen des gewählten Ladeports (A,F) an. Bitte

achten Sie darauf die positiven und negativen Anschlüsse nicht zu verpolen.

2. Schließen Sie den JST-XH Balance Adapter an den Balanceboardanschluss (D,H) des gewählten

Ladeanschluss an.

3. Schließen Sie den Akkuanschluss an das Ladekabel an.

4. Schließen Sie den Balanceranschluss des Akkus an den JST_XH Balanceadapter an.

5. Drücken Sie den ESC /Mode Button um durch die Hauptmenüs zu scrollen bis Sie die Anzeige

Program Select=Li-Po/Li-Ion/Li-Fe erreicht haben.

6. Drücken Sie Start / Enter.

7. Drücken Sie den Dec oder Inc Button bis die Anzeige Li-Po/Li-Ion/Li-Fe DCHG (DCHG =

Entladen) erscheint.

8. Drücken Sie den Start / Enter Button um die Parameter einzustellen.

9. Haben Sie die Parameter wie gewünscht eingestellt, drücken und halten Sie den Start / Enter
Button für drei Sekunden.

10. Das Ladegerät prüft den Akku und die Einstellungen und der Entladevorgang beginnt.

11. Drücken Sie den Dec oder Inc Button um die weiteren Entladeinformation zu sehen.

12. Drücken Sie den ESC / Mode Button um den Entladevorgang zu einem beliebigen Zeitpunkt zu
beenden.

13. Ist der Entladevorgang beendet ertönt eine Tonserie.

14. Trennen Sie den Akku vom Ladeadapter.

4.20 4.20 4.20

0.00 0.00 0.00

1 - SELBSTEST UND PROGRAMMAUSWAHL

Ist das Ladegerät eingeschaltet (ON) führt es einen Selbsttest durch und auf dem Display wird der
Markename und die Modellnummer angezeigt.

IN DEN FOLGENDEN DREI SEKTIONEN WERDEN NUR LI-PO AKKUS ABGEBILDET.
LI-ION UND LI-FE AKKU UNTERSCHEIDEN SICH NUR IN DER ZELL- UND
AKKUSPANNUNG.

Lithium Akkus (Li-Po / Li-Fe / Li-Ion)

Ni-MH Akkus

Ni-Cd Akkus

Blei-Gel Akkus

DIGITAL POWER

DATEN SPEICHERN

DATEN LADEN

zUM STArTEN

kUrzANLEITUNG PrOGrAMMIErUNG

BETrIEB DES LADEGEräTES

© 2015 Horizon Hobby, LLC. Dynamite, Prophet and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC.

Werte in Bildschirme dienen nur als Beispiel

PROGRAM SELECT
NiMH Battery

PROGRAM SELECT
NiCd Battery

PROGRAM SELECT
Pb Battery

PROGRAM SELECT
Memory Save

PROGRAM SELECT
Memory Load

MEMORY NiMH [1]
AUTO 1.5A

MEMORY NiMH [1]
AUTO 1.5A

PROGRAM SELECT
Digital Power

NiMH CHARGE Man
CURRENT 1.0A

NiMH CHARGE Aut
CUR LIMIT 1.0A

NiMH DISCHARGE

1.0A 12.0V

C=1.0A D=1.0A 1

NiCd CHARGE Man
CURRENT 1.0A

NiCd CHARGE Aut
CUR LIMIT 1.0A

NiCd DISCHARGE

1.0A 12.0V

C=1.0A D=1.0A 1

Pb CHARGE

0.1A 4.9V (2P)

Pb DISCHARGE

1.0A 4.9V (2P)

POWER MODE

2.0A 12.0V

HINWEIS: Diese Anwendung ist nicht geeignet für Personen mit reduzierter physikalischer Sensorik
oder eingeschränkten mentalen Fähigkeiten oder mangelhafter Erfahrung, solange sie nicht unter
Aufsicht und Anleitung einer für ihre Sicherheit verantwortlichen Person stehen.

ACHTUNG GEFAHR! Folgen Sie bitte sorgfältig diesen Anweisungen um das
Kurzschluss-oder Brandrisiko zu minimieren.

hINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen
von Horizon Hobby, LLC jederzeit geändert werden. Die aktuelle Produktliteratur finden Sie auf
horizonhobby.com unter der Registerkarte „Support“ für das betreffende Produkt.

SPEzIELLE BEDEUTUNGEN

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf
unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise
Sachschäden UND geringe oder keine Gefahr von Verletzungen ergeben.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich
Sachschäden UND die Gefahr von schweren Verletzungen.

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich
Sachschäden, Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit
oberflächliche Verletzungen.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit

den Produktfunktionen vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann
dies zu Schäden am Produkt oder persönlichem Eigentum führen oder schwere Verletzungen
verursachen.
Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem
Menschenverstand betrieben werden und benötigt gewisse mechanische Grundfähigkeiten. Wird
dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise betrieben, kann dies zu
Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses Produkt eignet
sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwachsenen.
Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, LLC, das Produkt zu zerlegen,
es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern.
Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist
unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen und
Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben
werden kann und Schäden oder schwere Verletzungen vermieden werden.

Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

ACHTUNG: Bitte stellen Sie sicher, dass die verwendeten Akkus mit den Spezifikationen

des Ladegerätes übereinstimmen und die Einstellungen des Ladegerät korrekt eingestellt
sind. Ein Nichtbefolgen kann zu großer Hitze und weiteren Fehlfunktionen führen, die zu
Personen- oder Sachschäden führen können. Bitte kontaktieren Sie Horizonhobby oder einen
autorisierten Händler wenn Sie Fragen zur Akkukompatibilität haben.

WARNUNG: Lassen Sie niemals das Ladegerät unbeaufsichtigt. Überschreiten Sie niemals den

maximalen Ladestrom. Laden Sie niemals nicht geeignete Akkus oder Akkus im falschen Mode.

Falsche oder Fehlbedienung kann zu großer Hitze, Feuer oder tödlichen Verletzungen führen.

WARNUNG: Unaufmerksamkeit oder falscher Gebrauch des Produktes in Zusammenhang

mit den folgenden Warnungen kann zu Fehlfunktionen, elektrischen Störungen, große

Hitzeentwicklung, FEUER, und tötlichen Verletzungen und Sachbeschädigungen führen.

Li** BAL-CHG 6S
C= 5000mAh 5.0A

Li** CHARGE 6S
C= 5000mAh 5.0A

Li** STORAGE 6S
C= 5000mAh 5.0A

Li** DCHG 3.0

1.0A 18.0V(6S)

PROGRAM SELECT
Li** Battery

PROGRAM SELECT
Li** Battery

DYNAMITE
DYNC2040

Li** BAL-CHG 3S
C= 2200mAh 2.2A

Li** DCHG 3.0V

1.0A 9.0V(3S)

LiPo STORAGE 3S
C= 3200mAh 2.0A

Li** BAL-CHG 3S
C= 3200mAh 3.2A

DYNc2040

SIchErhEITShINWEISE UND WArNUNGEN

• LASSEN SIE DAS, LADEGERÄT UND AKKU NIEMALS UN¬BEAUFSICHTIGT WÄHREND
DES BETRIEBES.

• LADEN SIE NIEMALS AKKUS ÜBER NACHT.

• Versuchen Sie niemals defekte, beschädigte oder nasse Akkus zu laden.

• Versuchen Sie niemals einen Akkupack zu laden der aus verschiedenen Akkutypen besteht.

• Erlauben Sie nicht Kinder unter 14 Jahren Akkus zu laden.

• Laden Sie niemals Akkus in extrem heißen oder kalten Orten oder in direkter Sonneneinstrahlung.

• Laden Sie niemals einen Akku dessen Kabel gekürzt oder beschädigt ist.

• Verwenden Sie niemals ein gekürztes oder beschädigtes Netz- oder Stromkabel.

• Schließen Sie niemals ein Ladegerät an eine 12 Volt Fahrzeugbatterie an wenn das Fahrzeug läuft.

• Versuchen Sie niemals ein Ladegerät auseinander zu bauen oder eine beschädigtes Ladegerät zu

verwenden.

• Schließen Sie am Ladegerät niemals gleichzeitig den AC oder DC Stromeingang an.

• Schließen Sie niemals den DC Anschluss am AC Netzstrom an.

• Verwenden Sie nur wiederaufladbare Akkus die für das Laden in dem korrekten Programm des

Ladegerätes geeignet sind.

• Überprüfen Sie immer den Akku vor dem Laden.

• Halten Sie den Akku stets fern von Materialien die durch Hitze beeinflusst werden können.

• Halten Sie den Ladevorgang im Blick und stets einen Feuerlöscher verfügbar.

• Sollte der Akku beim Laden oder im Flug beginnen, sich auszudehnen oder anzuschwellen stoppen

Sie den Ladevorgang oder den Flug unverzüglich.

• Schließen Sie zuerst das Ladekabel an das Ladegerät an und dann den Akku um Kurzschlüsse zu
vermeiden. Trennen Sie die Verbindung in umgekehrter Reihenfolge.

• Schließen Sie den Pluspolanschluss (+) und den Minuspolanschluss (-) stets korrekt an.

• Trennen Sie nach dem Laden immer den Akku vom Ladegerät und lassen das Ladegerät zwischen

dem Laden abkühlen.

• Laden Sie stets in einem gut belüfteten Bereich.

• Beenden Sie bei Fehlfunktion sofort alle Prozesse und kontakten den technischen Service von

Horizon Hobby.

• Laden Sie nur wiederaufladbare Akkus. Dass Laden von nicht aufladbaren Batterien kann diesem
zum Platzen bringen und Verletzungen und Sachschäden zur Folge haben.

• Die Mehrfachsteckdose sollte sich in der Nähe der Ausrüstung befinden und leicht erreichbar sein.