Dynamic Engineering PMC-UNIV-TEST, PMC-UNIV-TEST-ENG User Manual

DYNAMIC ENGINEERING

150 Dubois St. Suite C, Santa Cruz, CA 95060

831-457-8891 Fax [phone]

http://www.dyneng.com

[e-mail]

Est. 1988

User Manual

PMC-UNIV-TEST

PMC-UNIV-TEST-ENG

Revision A1 Revised 9/24/18

Corresponding Hardware: Revision A

Fab numbers: 10-2018-1201

Embedded Solutions Page 2

PMC-UNIV-TEST
PCI and PMC Compatible Carrier

Dynamic Engineering
150 Dubois St. Suite C
Santa Cruz, CA 95060
831457-8891
831457-4793 FAX

This document contains information of
proprietary interest to Dynamic Engineering. It
has been supplied in confidence and the
recipient, by accepting this material, agrees that
the subject matter will not be copied or
reproduced, in whole or in part, nor its contents
revealed in any manner or to any person except
to meet the purpose for which it was delivered.

Dynamic Engineering has made every effort to
ensure that this manual is accurate and
complete. Still, the company reserves the right
to make improvements or changes in the
product described in this document at any time
and without notice. Furthermore, Dynamic
Engineering assumes no liability arising out of
the application or use of the device described
herein.

The electronic equipment described herein
generates, uses, and can radiate radio
frequency energy. Operation of this equipment
in a residential area is likely to cause radio
interference, in which case the user, at his own
expense, will be required to take whatever
measures may be required to correct the
interference.

Dynamic Engineering’s products are not
authorized for use as critical components in life
support devices or systems without the express
written approval of the president of Dynamic
Engineering.

Connection of incompatible hardware is likely to
cause serious damage.

©2018 by Dynamic Engineering.
Other trademarks and registered trademarks are owned by their
respective manufactures.

Embedded Solutions Page 3

PRODUCT DESCRIPTION 4!

Headers and TestPoints 6!

PMC Module Backplane IO Interface Pin Assignment 7!

Construction and Reliability 8!

Thermal Considerations 8!

WARRANTY AND REPAIR 9!

Service Policy 9!

Out of Warranty Repairs 9!

For Service Contact: 9!

SPECIFICATIONS 10!

ORDER INFORMATION 11!

FIGURE 1! PMC-UNIV-TEST PN4 INTERFACE STANDARD 7!

Table of Contents

List of Figures

Embedded Solutions Page 4

Product Description

PMC-UNIV-TEST and PMC-UNIV-TEST-ENG are part of the Dynamic Engineering PCI
and PMC Compatible family of modular I/O components. Both adapt a PMC to one PCI
slot. The devices are for test support. Testpoints for the PCI bus plus JTAG are
provided on both versions.

In a PCI position, the B side is forward the A side is the rear. PMC-UNIV-TEST has the
Host/carrier side connectors mounted to the A side. The PMC will have it’s main
component side forward in this configuration. The SCSI connector is routed to the Jn4
/ Pn4 PMC connector to provide a method of connecting to “user IO” while testing.

“B” Front side with the testpoints and SCSI.

“A” Rear side with carrier type connectors to mate to PMC.

Note mounting holes to optionally connect PMC to Carrier via 10 mm standoff positions.

Embedded Solutions Page 5

PMC-UNIV-TEST-ENG has some modifications when compared with the standard
version. The B side PMC type connectors are added, the SCSI is removed, and the
testpoints are moved to the opposite side. In this configuation the PMC side connectors
can be installed into the host board, and the PMC can be installed into the carrier
connectors on the A side [now facing up]. The testpoints are now on the A side to make
them more convenient and provide a method of probing the PCI bus while the PMC is
installed into the carrier via PMC-UNIV-TEST-ENG.

“B” Front side with the PMC type connectors – “plugs into

host”

“A” Rear side with carrier type connectors to mate to PMC.
Note headers are this side for the –ENG configuration as it will be up to mate with the
PMC. The headers will be away from the PMC A secondary riser may be required with
cPCI etc depending on how low the PMC connectors are located to the bottom edge of
the carrier.

Special features:

• Passive 32 bit Universal voltage design

• Bipass capacitors on all PMC power pins plus 10 uF on 5V and 3.3V.

• JTAG header routed to PMC connections

• PCI test points – easy to read staggered Silk labels both sides

• 8 grounds to support logic analyzer connection as well as ocilloscope

• User IO [Pn4] available through SCSI connector on standard model.

Embedded Solutions Page 6

Headers and TestPoints

PCI 56 testpoints are supplied each labeled with the PCI signal attached. Some names

are truncated to allow larger easier to read print.

JTAG TRST, TDI, TDO, TMST, TCK plus a 3.3V and a Ground reference to interface

with the installed PMC via the JTAG signals.

GND 8 Ground testpoints are spaced along the top of the PCI signals to support Logic

Analyzer and Ocilloscope reference. Each are labeled GND.

Embedded Solutions Page 7

PMC Module Backplane IO Interface Pin Assignment

The figure below gives the pin assignments for the PMC Module IO Interface – from
Pn4 to the PCIeBPMCX1 connectors. Also see the User Manual for your PMC board for
more information.

SCSI II [P2] Pn4
35 36 1 2

1 2 3 4
37 38 5 6
3 4 7 8
39 40 9 10
5 6 11 12
41 42 13 14
7 8 15 16
43 44 17 18
9 10 19 20
45 46 21 22
11 12 23 24
47 48 25 26
13 14 27 28
49 50 29 30
15 16 31 32
51 52 33 34
17 18 35 36
53 54 37 38
19 20 39 40
55 56 41 42
21 22 43 44
57 58 45 46
23 24 47 48
59 60 49 50
25 26 51 52
61 62 53 54
27 28 55 56
63 64 57 58
29 30 59 60
65 66 61 62
31 32 63 64
33 67 Open
34 68 Open

FIGURE 1 PMC-UNIV-TEST PN4 INTERFACE STANDARD

Read table:
P2-1 = Pn4-3
P2-35 = Pn4-1
etc.
Signals are matched length and differentially routed with 100 ohm impendance

Embedded Solutions Page 8

Construction and Reliability

PMC-UNIV-TEST is constructed out of 0.062 inch thick high temp RoHS compliant FR4
material.

Surface mounted components are used. The connectors are SMT for the PMC bus and
through hole for the testpoints and IO.

The PMC Module connectors are keyed and shrouded with Gold plated pins on both
plugs and receptacles. They are rated at 1 Amp per pin, 200 insertion cycles minimum.
These connectors make consistent, correct insertion easy and reliable. With careful
installation the connectors will last longer and jambing on will result in a shorter lifespan.

The PMC Module is secured against the carrier with the PMC connectors. It is
recommended, for enhanced security, that the PMC mounting screws are installed. The
screws and stand-off’s are supplied with the PMC from the OEM. Dynamic Engineering
has screws, standoffs, blank bezels and other PMC hardware available at a reasonable
cost if your PMC was not shipped with some of the required attachment hardware or if it
has been misplaced.

Thermal Considerations

If the PMC installed has a large heat dissipation; forced air cooling is recommended.
Since the PMC is vertical and the lid is off the box, standard air-flow may need to be
enhanced.

Embedded Solutions Page 9

Warranty and Repair

Please refer to the warranty page on our website for the current warranty offered and
options.

http://www.dyneng.com/warranty.html

Service Policy

Before returning a product for repair, verify as well as possible that the suspected unit is
at fault. Then call the Customer Service Department for a RETURN MATERIAL
AUTHORIZATION (RMA) number. Carefully package the unit, in the original shipping
carton if this is available, and ship prepaid and insured with the RMA number clearly
written on the outside of the package. Include a return address and the telephone
number of a technical contact. For out-of-warranty repairs, a purchase order for repair
charges must accompany the return. Dynamic Engineering will not be responsible for
damages due to improper packaging of returned items. For service on Dynamic
Engineering Products not purchased directly from Dynamic Engineering contact your
reseller. Products returned to Dynamic Engineering for repair by other than the original
customer will be treated as out-of-warranty.

Out of Warranty Repairs

Out of warranty repairs will be billed on a material and labor basis. Customer approval
will be obtained before repairing any item if the repair charges will exceed one half of
the quantity one list price for that unit. Return transportation and insurance will be billed
as part of the repair and is in addition to the minimum charge.

For Service Contact:

Customer Service Department
Dynamic Engineering
150 DuBois St. Suite C
Santa Cruz, CA 95060
831-457-8891 831-457-4793 fax Internet Address [e-mail]

Embedded Solutions Page 10

Specifications

Logic Interfaces: PCI 32 bit Universal Voltage.

Access types: All PCI supported

CLK rates supported: 25-66 [likely work at higher rates as PCI signals are matched and

controlled. ]

Software Interface: Passive, no SW required for adapter

Testpoints: PCI signals plus JTAG and grounds

Interface: PMC front bezel directly, rear IO via SCSI connector.

Dimensions: minimized to cover as little of the PMC as possible.

Construction: High Temp FR4 Multi-Layer Printed Circuit, Through Hole and

Surface Mount Components.

Embedded Solutions Page 11

Order Information

standard temperature range -40ó85øC
PMC-UNIV-TEST Vertical mount component side forward PMC adapter

into PCI. 32 bit universal voltage PCI bus interface.
Testpoints on PCI, JTAG signals. Impedance
controlled, matched length routing. SCSI connector
differentially routed to Pn4 for rear IO applications.

-ROHS [ROHS compliant parts and process]

-ENG add second connector set, remove SCSI,
switch headers to A side.

http://www.dyneng.com/PMC-UNIV-TEST.html

HDEterm68 http://www.dyneng.com/HDEterm68.html

68 pin SCSI II to 68 screw terminal converter with DIN
rail mounting.

HDEcabl68 http://www.dyneng.com/HDEcabl68.html

SCSI cables with latch blocks or thumbscrews and
various lengths are available. Custom lengths can be
ordered.

All information provided is Copyright Dynamic Engineering