Dynamic Engineering PCI2PMC User Manual

DYNAMIC ENGINEERING

150 DuBois St. Suite C, Santa Cruz, Calif. 95060

831-457-8891 Fax [phone]

http://www.dyneng.com

[e-mail]

Est. 1988

User Manual

PCI2PMC

PCI Single Slot PMC Compatible Carrier

Use Your PMC in a PC

Manual Revision H1

Corresponding Hardware: Revision H

10-2000-0608

Embedded Solutions Page 2

PCI2PMC

PCI and PMC Compatible Carrier

Dynamic Engineering
150 DuBois St. Suite C
Santa Cruz, CA 95060
831-457-8891
831-457-4793 FAX

This document contains information of
proprietary interest to Dynamic Engineering. It
has been supplied in confidence and the
recipient, by accepting this material, agrees that
the subject matter will not be copied or
reproduced, in whole or in part, nor its contents
revealed in any manner or to any person except
to meet the purpose for which it was delivered.

Dynamic Engineering has made every effort to
ensure that this manual is accurate and
complete. Still, the company reserves the right to
make improvements or changes in the product
described in this document at any time and
without notice. Furthermore, Dynamic
Engineering assumes no liability arising out of
the application or use of the device described
herein.

The electronic equipment described herein
generates, uses, and can radiate radio
frequency energy. Operation of this equipment
in a residential area is likely to cause radio
interference, in which case the user, at his own
expense, will be required to take whatever
measures may be required to correct the
interference.

Dynamic Engineering’s products are not
authorized for use as critical components in life
support devices or systems without the express
written approval of the president of Dynamic
Engineering.

Connection of incompatible hardware is likely to
cause serious damage.

©2000-2010 by Dynamic Engineering.
Other trademarks and registered trademarks are
owned by
their respective manufactures.

Embedded Solutions Page 3

Table of Contents

PRODUCT DESCRIPTION 5

USAGE NOTES: 6

Notes: 8

PMC MODULE BACKPLANE IO INTERFACE PIN ASSIGNMENT 9

APPLICATIONS GUIDE 10

Interfacing 10

Construction and Reliability 11

Thermal Considerations 11

WARRANTY AND REPAIR 12

Service Policy 12

Out of Warranty Repairs 12

For Service Contact: Customer Service Department Dynamic Engineering 12

SPECIFICATIONS 13

ORDER INFORMATION 14

Embedded Solutions Page 4

List of Figures

FIGURE 1 PCI2PMC PN4 INTERFACE STANDARD 9

Embedded Solutions Page 5

Product Description

PCI2PMC is part of the PCI and PMC Compatible family of modular I/O components.
The PC2PMC adapts one PMC to one PCI slot. Dynamic Engineering has several
versions of the PCI2PMC including bridged and two slot versions. The PCI2PMC is a
single slot passive design.

Special features:

• Universal PCI 1/2 length card.
LED’s are green and steady on when the voltages are active.

• LED1 is PMC Busmode “Present”

• LED2 is 3.3V to PMC

• LED3 is 3.3 from PCI bus.

• LED4 is 3.3 from Regulator

• LED5 is plus 5

• LED6 is plus 12

• LED7 is minus 12

• Jumper selection for onboard 1500mA regulator or PCI 3.3V supply

• 32 or 64 bit operation

•10 ohm series resistors on AD31-0

• Clamping Diodes on critical PCI signals

• Zero delay buffer for PCI clock distribution

• PrPMC clocking options

• Front panel connector access through PCI bracket

• User IO [Pn4] available through 2 cable connectors (DIN IDC and SCSI II compatible)

• Spare pins on SCSI connector can be jumper selected to 5V or ground.

• Matched length IO.

• Cooling cutout for increased airflow to PMC

• Jumper selection on M66EN

• JTAG and Monarch mode control header options

PCI2PMC is a passive design incurring no added delays in connection from the PCI to
the PMC buses. The design incorporates features to prevent the physical length of the
traces from affecting operation. There may be cases where the backplane can’t support
all slots with PCI2PMC cards installed.

Our bridged products including PCIBPMC, PCIBPMCET, PCIBPMCX1, and
PCIBPMCX2 can be used in situations where a bridge is desired. Please refer to the
Dynamic Engineering website for more information on these and other products.