Dynamic Cooking Systems BGB30-BQR Service Manual

THE PROFESSIONAL
30” BGB GRILL

Use and Care Guide

MODELS:

BGB30-BQR

1

Thank you for selecting this DCS Professional “BGB” Series Grills. Because of these appliances unique
features we have developed this Use and Care Guide. It contains valuable information on how to properly
operate and maintain your new appliance for years of safe and enjoyable cooking.

To help serve you better,please fill out and submit your Ownership Registration Card by visiting our website
at www.dcsappliances.com and selecting “Customer Service” on the home page and then select
“Ownership Registration” or submit the enclosed Ownership Registration Card to the address below. In
addition, keep this guide handy, as it will help answer questions that may arise as you use your new
appliance.

For your convenience,product questions can be answered by a DCS Consumer Service Representative at
1-888-281-5698, Fax: [phone], email: [e-mail],or by mail:

WAR NI NG

Improper installation, adjustment alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating and
maintenance instructions thoroughly before use, installing or servicing this
equipment. For outdoor use only.

FOR YOUR SAFETY

1. Do Not store or use gasoline or any other flammable vapors and liquids in
the vicinity of this or any other appliance.

2. An LP cynlinder not connected for use shall not be stored int he vicinity of
this or any other appliance.

FOR YOUR SAFETY

IF YOU SMELL GAS:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues,immediately call your gas supplier or your fire department.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647

A MESSAGE TO OUR CUSTOMERS

2

SAFETY PRACTICES & PRECAUTIONS.......................................................................................................3-5

GRILL MODELS................................................................................................................................................................6

GAS REQUIREMENTS..............................................................................................................................................7-8

LOCATING GRILL / BUILT-IN CLEARANCES.........................................................................................9-10

BUILT-IN CONSTRUCTION DETAILS..............................................................................................................11

LEAK TESTING ...............................................................................................................................................................12

INSTALLER FINAL CHECKLIST...........................................................................................................................13

BURNER ADJUSTMENTS.......................................................................................................................................14

USING THE GRILL .................................................................................................................................................15-17

LIGHTING INSTRUCTIONS ...................................................................................................................................17

USING THE ROTISSERIE ..................................................................................................................................18-21

CARE & CLEANING.....................................................................................................................................................22

BURNER REMOVAL & CLEANING ...................................................................................................................23

TROUBLESHOOTING................................................................................................................................................24

PA RT S LISTS

Grill Burner Assembly Parts List ..................................................................................................................25

Grill Body Parts List ..........................................................................................................................................26

Rotisserie Assembly Parts List......................................................................................................................27

30 Grill Cart Parts List......................................................................................................................................28

Cart Assembly Instrucitons.....................................................................................................................29-31

WIRING DIAGRAM

Wiring Diagram – BGA30-BQR Models ....................................................................................................32

SERVICE..............................................................................................................................................................................33

WAR RANT Y......................................................................................................................................................................34

TABLE OF CONTENTS

3

IMPORTANT SAFETY NOTICE:

Certain Liquid Propane dealers may fill liquid propane cylinders for use in the
grill beyond cylinder filling capacity. This “Overfilling” may create a dangerous
condition.

“Overfilled” tanks can build up excess pressure. As a safety device, the tanks pressure relief valve will
vent propane gas vapor to relieve this excess pressure. This vapor is combustible and therefore can be
ignited. To reduce this danger, you should take the following safety precautions:

1. When you have your tank filled, be sure you tell the supplier to fill it to no more than 3/4 (75%)
of its total capacity.

2. If you own or use an extra spare tank, or have a disconnected tank, you
should NEVER store it near or under the grill/cart unit or heat box, or near
any other ignition or heat source. A metallic sticker with this warning is
attached to the grill to remind you, your family and all others who may
use your BBQ grill of these safety precautions.

Do not remove this sticker.

WAR NING:

Do not try lighting this appliance without reading the
“LIGHTING INSTRUCTIONS” section of this manual.

This Grill is for outdoor use only.

WAR NING:

Push and hold the igniter button, turn the selected burner knob to “HI”. If
burner does not light in 4 to 5 seconds turn knob “OFF” and wait 5 minutes
before trying again for any accumulated gas to dissipate.

 Begin by insuring proper installation and servicing. Follow the installation instructions

provided with this product. Have your grill installed by a qualified technician. Have the installer
show you where the gas supply shut off valve is located so that you know where to shut off the
gas to the grill. If you smell gas, your installer has not done a proper job of checking for leaks.
If the connections are not perfectly sealed, you can have a small leak and therefore a faint gas
smell. Finding a leak is not a “do-it-yourself ”procedure. Some leaks can only be found with the
burner control in the “ON”position and this must be done by a qualified technician.

 Children should not be left alone or unattended in an area where the grill is being used. Never

allow them to sit, stand or play on or around the grill at any time. When in use, portions of the
grill get hot enough to cause severe burns.

 Do not store items of interest to children around or below the grill, in the cart or masonry

enclosure. Never allow children to crawl inside a cart or enclosure.

 Never let clothing,pot holders or other flammable materials come in contact with or too close

to any grate, burner or hot surface until it has cooled. Fabric may ignite and result in personal
injury.

 Do not heat unopened food containers as a build-up of pressure may cause the container to

burst.

 Always use a covered hand when opening the grill lid and only do so slowly to allow heat and

steam to escape.

 Never lean over an open grill. When lighting a burner, always pay close attention to what you

are doing. Be certain you are pushing the ignition button when you attempt to light the grill.

SAFETY PRACTICES & PRECAUTIONS

4

For personal safety,wear proper apparel. Loose fitting garments or sleeves should never be worn while
using this appliance. Some synthetic fabrics are highly flammable and should not be worn while cook-
ing. Only certain types of glass, heat-proof glass ceramic, earthenware,or other glazed utensils are suit-
able for grill use. Use of these types of materials may break with sudden temperature changes. Use
only on low or medium heat settings according to the manufacturer’s directions.

WAR NING:

Spiders and insects can nest in the burners of this and any other grill, and cause
the gas to flow from the front of the burner. This is a very dangerous condition
which can cause a fire to occur behind the valve panel, thereby damaging the
grill components and making it unsafe to operate.

WAR NING:

Keep the area surrounding the grill free from combustible materials, trash, or
combustible fluids and vapors such as gasoline or charcoal lighter fluid. Do
not obstruct the flow of combustion and ventilation air.

WAR NING:

Never use the grill in windy conditions. If located in a consistently windy area
(oceanfront, mountaintop, etc.) a wind break will be required. Always adhere
to the specified clearances listed.

PREFERRED AIR FLOW

GRILL EXHAUST

EXHAUST

FLAME

BURNER

WIND

WIND

PRIMARY

INTAKE

AIR FLOW

EXHAUST VENT FLOW

GRILL PLACEMENT

 When using the grill, do not touch the grill burner grate or immediate surrounding area as

these areas become extremely hot and could cause burns.

 Grease is flammable. Let hot grease cool before attempting to handle it. Avoid letting grease

deposits collect in the drip pan. Clean often.

 Do not use aluminum foil to line drip pans or grill racks. This can severely upset combustion air

flow or trap excessive heat in the control area. The result of this can be melted knobs or
damaged ignition components.

SAFETY PRACTICES & PRECAUTIONS

FLAME LIFT

5

 When using the open top burners always use flat bottomed utensils which are large enough to

cover the burner. Adjust the flame so that it heats only the bottom of the pan to avoid ignition
of clothing. Position handles inward away from open edges of the unit to avoid burns
associated with unintentional spillovers. Hold the handle of the pan to prevent movement of
the utensil when turning or stirring food. For proper lighting and performance of the burners
keep the ports clean. It is necessary to clean them periodically for optimum performance.

 Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the

grill while it is hot. Some cleaners produce noxious fumes or can ignite if applied to a hot
surface.

 Be sure all grill controls are turned off and the grill is cool before using any type of aerosol

cleaner on or around the grill. The chemical that produces the spraying action could, in the
presence of heat, ignite or cause metal parts to corrode.

 Do not use the grill for cooking excessively fatty meats or products which promote flare-ups.

 Never grill without the drip pan and grease tray in place and pushed all the way to the back of

the grill. Without it hot grease could leak downward and produce a fire or explosion hazard.

 Do not operate the grill under unprotected combustible construction. Use only in well

ventilated areas. Do not use in buildings, garages, sheds, breezeway or other such enclosed
areas. This unit is for outdoor use only.

 If a cart unit is stored indoors ensure that it is cool, fold the side shelf down, then push, never

pull, the grill. If LP,the cylinder must be unhooked and the LP cylinder stored outside in a well
ventilated area, out of reach of children.

 Do not use charcoal in the grill.

 Keep any electrical supply cord,or the rotisserie motor cord away from the heated areas of the

grill and water (pools, fountains, puddles).

 Never use a dented or rusty LP tank. Keep the ventilation openings of the cylinder enclosure

free and clear from debris.

 Use only dry potholders; moist or damp potholders on hot surfaces may cause burns from

steam. Do not use a towel or bulky cloth in place of potholders. Do not let potholders touch
hot portions of the grill or burner grate.

 CALIFORNIA PROPOSITION 65-WARNING: The Burning of gas cooking fuel generates some

by-products which are on the list of substances which are known by the State of California to
cause cancer or reproductive harm. California law requires businesses to warn customers of
potential exposure to such substances. To minimize exposure to these substances always
operate this unit according to the Use and Care Manual,ensuring you provide good ventilation
when cooking with gas.

 This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles

and/or boats.

SAFETY PRACTICES & PRECAUTIONS

6

BGB30-BQR

GRILL MODELS

R

O

T

I

S

S

E

R

I

E

7

Verify the type of gas supply to be used, either
natural or LP, and make sure the marking on the
appliance rating plate agrees with that of the
supply. The rating plate is located on the inside
back wall of the Grill. Never connect an
unregulated gas line to the appliance.

An installer supplied gas shut-off valve must be
installed in an easily accessible location. All
installer supplied parts must conform to local
codes, or in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70 or the
Canadian Electrical Code, CSA C22.1, and the
National Fuel Gas Code, ANSI Z223.1 or
CAN/CGA-B149.1 Natural Gas Installation Code
or CAN/CGA-B149.2 Propane Installation Code.

All pipe sealants must be an approved type and
resistant to the actions of LP gases. Never use
pipe sealant on flare fittings. All gas connections should be made by a qualified technician and in
accordance with local codes and ordinances. In the absence of local codes, the installation must
comply with the national fuel gas code ANSI Z223.1. Gas conversion kits are available from the factory.
When ordering gas conversion kits have the model number, and the type of gas (natural or LP) from
your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB30-BQR - 50,0 00 Btu/hr
The appliance and its individual shut off valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The
appliance must be isolated from the gas supply piping system by closing its individual manual shut­off valve during any pressure testing of the gas supply piping system at test pressures equal to or less
than 1/2 PSIG (3.5 kPa.). The installation of this appliance must conform with local codes or, in the
absence of local codes, with the national fuel gas code, ANSI Z223.1. Installation in Canada must be in
accordance with the Standard CAN/CGA-B149.2 Propane Installation Code and local codes.

NATURAL GAS HOOK UP:

(This type of connection should be performed by a certified or
licenced technician only.)
Connection: 1/2" NPT male with 3/8" flare adapter. Operating pressure: 4.0" W.C.
Supply pressure: 5" to 14" water column. If in excess of 14" W.C. a step down regulator is required.

Check with your local gas utility company or with local codes for instructions on installing gas supply
lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas line is too
small, the grill will not function properly. Any joint sealant used must be an approved type and be
resistive to the actions of LP gases.

TO HOOK-UP THE FITTINGS SUPPLIED WITH THE GRILL:

Assemble as shown (Fig.01). Use threading compound on male threads only. Do not use threading
compound on the male end of the 1/2 NPT to 3/8 flare adapter. Use a second pipe wrench to hold the
grill inlet pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points
in the direction of gas flow towards the unit,away from the supply. Do not forget to place the installer
supplied gas valve in an accessible location.

FIG.01 Natural Gas

GAS REQUIREMENTS

Bottom of unit

Coupling

1/2 NPT
Close
NIpple

Regulator

4.0" W.C.

Adapter 1/2 NPT
to 3/8 flare fitting

Do not put threading
compound on these
threads

*Installation must conform with local
codes or with the National Fuel Gas
Code ANSI Z223.1 or the CAN/CGA­B149.2 Propane Installation Code

Threading compound
must be resistant to LP gas

1/2 NPT
Close
NIpple

Installer supplied shut-off
valve must be easily
accessible*

8

LP GAS HOOK UP (TYPE 1 OR QCC1 REGULATOR):

Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assembly for
connection to a standard 20 lb. LP cylinder (Type 1). The LP tank is not included.

Connection: 1/2" NPT male with a 3/8" Flare adapter (included). LP Hose with a quick disconnect and
fittings are included. Operating pressure: 10.0" W.C.

To connect the LP regulator/hose assembly to the tank/valve assembly, first make sure the main valve on
the tank is completely closed. Although the flow of gas is stopped when the Type 1 system is discon­nected as part of of its safety feature, you should always turn off the LP tank main valve (Fig.02) after each
use and during transport of the tank or unit. Insert the regulator inlet into the tank valve and turn to the
black coupler clockwise until the coupler tightens up. Do not overtighten the coupler. Turn the main
tank valve on and turn the burner control valves on the unit to the “HI” position for about 20 seconds to
allow the air in the system to purge, turn valves off and wait 5 minutes before attempting to light the
burners.

To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn
counter clockwise. The inlet will then disengage, remove the inlet from the tank valve opening if it has
not already done so when it disengaged. Your local LP filling station should be equipped with the proper
equipment to fill your tank.

LP TANK REQUIREMENTS:

A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. Never use a
cylinder with a damaged valve. Always check for leaks after every LP tank change. The LP gas cylinder must be
constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of
Transportation (DOT or CAN/CSA-B339) and designed for use with a Type 1 system only. Do not change the
regulator/hose assembly from that supplied with the unit or attempt to use a Type 1 equipped regulator/hose
assembly with a standard 510 POL tank/valve assembly. The cylinder must be provided with a shut-off valve
terminating in an LP gas supply cylinder valve outlet specified, as applicable, for connection Type 1. If the

appliance is stored indoors,the cylinder must be disconnected and removed from the appliance. Cylinders
must be stored outdoors in a well-ventilated area out of the reach of children.

NOTE:When an LP unit is directly attached into an LP house system, the step down regulator MUST be

used to reduce the supply pressure to a max. 14”W.C.and min. 11” W.C. to the grill regulator.

FIG.02 LP Gas

GAS REQUIREMENTS

Adapter 1/2 NPT
to 3/8 flare fitting

Do not put threading
compound on these
threads

Bottom of unit

Threading compound
must be resistant to LP gas

Type 1 Regulator

Main Valve

LP Regulator hose
assembly 10" W.C.

*Installation must conform with local
codes or with the National Fuel Gas
Code ANSI Z223.1 or the CAN/CGA­B149.2 Propane Installation Code

Type 1 Tank

9

INSULATED JACKET:

Do not install the Grill under overhead unprotected combustible construction. If the Grill is to be
placed into a combustible enclosure use only the DCS insulated jacket which has specifically been
designed and tested for this purpose and is available from your dealer.

Location:

When determining a suitable location take into account concerns such as exposure to wind,proximity
to traffic paths and keeping any gas or electrical supply lines as short as possible. Locate the grill only
in a well ventilated area. Never locate the grill in a building, garage, breezeway, shed or other such
enclosed areas. During heavy use, the grill will produce a lot of smoke. Ensure there is adequate area
for it to dissipate.

IMPORTANT :

Gas fittings, regulator, and installer supplied shut-off valves must be easily
accessible.

Clearances to Combustible Construction:

A Minimum of 12" from the sides and a minimum of 12" from the back must be maintained from the
Grill above and below the cooking surface to adjacent vertical combustible construction. (Fig. 03) Do
not install under unprotected combustible construction.

Clearances to Non-Combustible Construction:

A minimum of 3" clearance from the back of the grill to non-combustible construction is required for
the purpose of allowing the lid to open fully. It is desirable to allow at least 6" side clearance to non­combustible construction above the cooking surface for counter space. If you’ll be using the rotisserie
option, the space is essential for motor and skewer clearance. The Grill can be placed directly adjacent
to non-combustible construction below the cooking surface. (Fig.03)

WARNING :

Failure to maitain required clearances creates a fire hazard that may result in
property damage or serious personal injury.

LOCATING GRILL/BUILT-IN CLEARANCES

FIG.03

30" Models = 39"

12"
(to left
and right
side of
grill to
combustible
construction)

(with rotisserie motor mounted)

R

O

T

I
S

S

E

R

I
E

rotisserie
motor

24-1/4"

10-1/2"

26-1/2"

Bottom of
support flange

grill

exhaust

3" (to non-combustible
construction / minimum

lid clearance)

12"

Maintain12"
from combustible
construction

10 -1/16"

2"

22-3/4"

25-1/2"

10

IMPORTANT:

It is recommended that a minmum of 10 sq. inches of ventilation opening be
provided for both the left and right sides, as well as the back of enclosure (fig.
3A). In order to safely dissapate unburned gas vapors in the event of a gas
supply leak.

WAR NING:

Note specific built in enclosure ventilaiton requirments. See text and fig 3A.

GENERAL

The Grill is designed for easy placement into masonry enclosures. For non-combustible applications
the grill drops into the opening shown in (Fig. 04) and hangs from its side flanges. A deck is not
required to support it from the bottom. When using the insulated jacket in a combustible enclosure
application, see the bottom of Fig. 04. The jacket assembly must be supported from the bottom by a
ledge on each side or a solid deck beneath the entire grill or insulated jacket.

Review the detail drawing shown (Fig. 04) and take into account the provisions shown for gas line
hook-up clearance in the right rear corner. The supporting ledges or deck must be level and flat. The
counter should also be level.

LOCATING GRILL/BUILT-IN CLEARANCES

FIG.3A

10 in.2 Min. ventilation

left hand side

1" Min.

Ventilation Requirements:

2

10 in.

Min. ventilation

on the back side

10 in.2 Min. ventilation
on the right hand side

11

j

BUILT–IN CONSTRUCTION DETAILS

FIG.04

grill

exhaust

3" (to non-combustible construction /
minimum lid clearance),

12" (to combustible construction)

13-3/4"

Bottom of
support flange

10-1/16"

2"

Standard layout for non-combustible enclosure:

10-1/8"

35-1/2"
Max.

Layout for insulated jacket only - combustible enclosure:

NOTE: See page 28, #29 for insulated

acket part ordering information.

22-3/4"

25-1/2"

30" Models = 28-1/2"

NOTE: See page 10
for ventilation notes.

30" Models = 34-7/8"

18-1/2"

20"

30" Models = 28"

3/4"

NOTE: If using a backguard apron or rear
wall, locate electrical service on the right
hand side for rotisserie motor connection

3" Min. for Lid
Clearance

22-3/4"

4" x 4" opening
for gas supply line

opening for access doors

NOTE: If using a backguard apron or rear
wall, locate electrical service on the right
hand side for rotisserie motor connection

3" Min. for Lid
Clearance

23-3/4"

11-1/8"

35-1/2"
Max.

18-1/2"

20"

30" Models = 28"

4" x 4" opening
for gas supply line

3-1/2"

opening for access doors

12

GENERAL:

Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete
gas tightness check must be performed at the installation site due to possible mishandling in
shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the whole
system for leaks, or immediately check if the smell of gas is detected.

Before Te sting:

Do not smoke while leak testing. Extinguish all open flames. Never leak test with an open flame.

Make a soap solution of one part liquid detergent and one part water. You will need a spray bottle,
brush,or rag to apply the solution to the fittings. For LP units,check with a full cylinder. The valve panel
must be removed to check the valves and fittings. Remove the knobs and the safety valve knob, then
remove the 4 screws which fasten the valve panel to the unit (you will need a torx head for this). Pull
the valve panel outward and unplug the wires from the ignition module and the back of the ignition
button. Remove the screws which hold the service panel in place.

To Test:

Make sure all control valves are in the“OFF” position. Turn the gas supply“ON”. Check all connections
from the supply line, or LP cylinder up to and including the manifold pipe assembly. Apply the soap
solution around the connection, valve, tubing and end of the manifold. Soap bubbles will appear
where a leak is present. If a leak is present, immediately turn off gas supply, tighten any leaking
connections, turn gas on, and recheck. Check all the gas connections at the base of the control valves
where they screw into the manifold pipe.

To check rotis burner and safety valve the burner must be lit, then leak test the connections located
behind the service panel. If you cannot stop a gas leak turn off the gas supply and call your local gas
utility, or the dealer you purchased the appliance from. Only those parts recommended by the
manufacturer should be used on the Grill. Substitution can void the warranty.

WARNING :

Do not use the grill until all connections have been checked and do not leak.

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy water near
the shut-off valve of the gas supply valve. Spray all the fittings. Bubbles indicate leaks. (Fig. 05 & 06)

LEAK TESTING

FIG.05 LP Gas

FIG.06 Nat. Gas

Bottom of unit

Bottom of unit

LEAK TEST POINTS

CHECK HOSE FOR
SIGNS OF ABRASIONS,
CRACKS, OR LEAKS

LP TANK

LEAK TEST POINTS

13

INSTALLER FINAL CHECKLIST:

GRILL BURNER FLAME HEIGHT:

To access the grill burner air shutters first remove the valve panel by removing it the same way as
described on page 12, section “Before Testing”.With a screw driver, loosen the lock-screw on the face
of the air shutter. Light the burner and adjust according to the directions below.

❏ Specified 12” clearances

maintained to combustibles.

❏ Verified proper enclosure

ventilation.

❏ Nylon straps removed from

burners.

❏ All internal packaging

removed.

❏ Knobs turn freely, bezels

centered.

❏ Each burner lights satisfac-

torily,individually or with
adjacent burner lit.

❏ Air shutters adjusted.

❏ Adjustable low setting satis-

factory.

❏ Drip pan in place properly

and sliding freely.

❏ Pressure regulator

connected and set for 4.0"
W.C.Natural, 11.2" W.C.LP
gas.

❏ Manual shut-off valve

installed and accessible.

❏ Unit tested and free of

leaks.

❏ User informed of gas supply

shut-off valve location.

❏ All radiants are assembled

(see page 15) and put in
place.

 PLEASE LEAVE THESE

INSTRUCTIONS WITH THE
USER.

 USER, PLEASE RETAIN

THESE INSTRUCTIONS
FOR FUTURE REFERENCE.

FIG. 07 Burner Flame Height

Sealed Burner

INSTALLER CHECKLIST/BURNER ADJUSTMENTS

FIG.09

3/8"

1-1/2"

14

Grill Burner Air Adjustment:

Each grill burner is tested and adjusted at the factory prior to shipment; however,variations in the local
gas supply or a conversion from one gas to another may make it necessary to adjust the burners. The
flames of the burners (except the rotisserie burner) should be visually checked and compared to that
of the drawing in Fig.07 and Fig. 09. Flames should be blue and stable with no yellow tips, excessive
noise or lifting. If any of these conditions exist, check if the air shutter or burner ports are blocked by
dirt, debris, spider webs, etc. Proceed with air shutter adjustment. The amount of air which enters a
burner is governed by a sheet metal cup at the inlet of the burner called an air shutter. It is locked in
place by a set screw which must be loosened prior to lighting the burner for adjustment.

Note: Side burner has no flame adjustment.

To Adjus t:

1. Be careful as the burner may be very hot.

2. If the flame is yellow, indicating insufficient air, turn the airshutter counterclockwise to allow more
air to the burner.

3. If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air
shutter clockwise.

4. Once adjusted turn the burner off and reverse steps to reassemble.

LOW SETTING ADJUSTMENTS:

The valves on the grill feature an adjustable low setting. Due to fluctuations in gas pressure, heating
value or gas conversion,you may feel it necessary to increase or
decrease gas flow in the low position. We do not recommend
adjusting the infrared rotis burner.

To Adjus t:

1. Light the burner.

2. Turn the control knob to the lowest setting (all the way

counter-clockwise).

3. Remove the knob.

4. While holding the valve shaft with pliers, insert a thin, flat

tipped screwdriver into the shaft and while viewing the
burner adjust to a minimum stable flame (Fig.10).

WAR NI NG: IMPORTANT!

Before lighting, inspect the gas supply piping or hose prior to turning the gas
"on". If there is evidence of cuts, wear, or abrasion, it must be replaced prior to
use.

FIG.10 Low Setting Adjustment

GRILL BURNER ADJUSTMENTS

15

GRILL:

Each grill section consists of a large stainless steel burner, stainless steel heat
baffles, a series of ceramic rods encased in a stainless steel rack, and a
stainless steel heat retaining grate. Each burner is rated at 25,000 Btu/hr.
Below the burners there is a stainless steel heat baffle which reflects usable
heat upward into the cooking area and reduces temperatures of the drip pan
below. Above the burners are stainless steel radiants which encase the
ceramic rods and protect the grill burner ports from blockage.

RADIANT ASSSEMBLY INSTALLATION:

1. Unpack ceramic rods and remove radiant (Fig. 12)
from the unit.

2. Unlock radiant end cap by pushing it up with two
fingers (Fig.13).

3. Place 18 ceramic rods on the radiant (Fig.14).

4. Lock radiant end cap (Fig.15).

5. Place the assembled radiant in the unit (Fig.16).

NOTE: In case a ceramic rod breaks:

a) Unlock radiant end cap by pushing it up with two fingers (Fig.13) or pliers may be used.
b) Replace broken ceramic rod.
c) Lock radiant end cap.

The Grill is supplied with radiant ceramic rods.Because of the porosity of ceramic rods, performance is
superior in the rods’ ability to capture heat as it rises from the grill burners. They also possess the
thermal mass needed for results. Flare ups are controlled because our radiant ceramic rods keep
grease from getting to the flames and igniting. The intense heat produced by this system produces
true grilled flavor as fats and juices are brought to the surface of the food and caramelized.
Discoloration is normal after use.

FIG.12

FIG.13

FIG.14

FIG.15

FIG.16

USING THE GRILL

FIG.11

16

REPLACEMENT OF REGULATORS AND HOSE

The pressure regulator and hose assembly supplied with the unit must be used. The replacement
pressure regulators and hose assembly must be the type specified by the manufacturer. Do not use
the grill if the odor of gas is present. If the unit is LP, screw the regulator into the tank and leak check
the hose and regulator connections with a soap and water solution before operating the grill. Turn all
knobs to "OFF" then turn on the gas supply. If LP, is there gas in the tank?

 Always keep your face and body as far away from the grill as possible when lighting.

 DO NOT leave the grill unattended while cooking.

 Keep a spray bottle of soapy water near the gas supply valve and check the connections before

each use.

 Do not attempt to "LITE" the grill if the odor of gas is present.

 Wait 5 minutes before relighting a hot grill.

IMPORTANT - USING THE GRILL:

Grilling requires high heat for searing and proper browning. Most foods are cooked at the “MEDIUM”
heat setting for the entire cooking time. However, when grilling large pieces of meat or poultry, it may
be necessary to turn the heat to a lower setting after the initial browning. This cooks the food through
without burning the outside. Foods cooked for a long time or basted with a sugary marinade may
need a lower heat setting near the end of the cooking time.

1. Check to be certain the drip pan and grease tray are in place.

2. Light the grill burners using the instructions in Use and Care Manual.

3. With the grill lid open, turn the control knob to “HI” to light. Preheat the grill for 5 to 10
minutes.

4. Place the food on the grill and cook to the desired doneness. Adjust heat setting, if
necessary. The control knob may be set to any position between “HI” and “LO”- most grilling
is between “MED” and “LO”.

5. Allow grill to cool and clean the grates, drip pan and grease tray after each use.

Note: If using LP gas, your preheat time may be shorter than recommended. To prevent

overcooking or burning you may want to lower heat settings.

GRILLING HINTS:

The doneness of meat, whether rare, medium, or well done, is affected to a large degree by the
thickness of the cut. Expert chefs say it is impossible to have a rare doneness with a thin cut of meat.
The cooking time is affected by the kind of meat, the size and shape of the cut, the temperature of the
meat when cooking begins, and the degree of doneness desired. When defrosting meats it is
recommended that it be done overnight in the refrigerator as opposed to a microwave. This in general
yields a juicier cut of meat. Use a spatula instead of tongs or a fork to turn the meat, as a spatula will
not puncture the meat and let the juices run out. To get the juiciest meats, add seasoning or salt after
the cooking is finished and turn the meat only once (juices are lost when the meat is turned several
times). Turn the meat just after the juices begin to bubble to the surface. Trim any excess fat from the
meat before cooking. To prevent steaks or chops from curling during cooking, slit the fat around the
edges at 2-inch intervals.

USING THE GRILL

17

Grilling Method Note: Indirect cooking method is a popular alternative to direct heat grilling. Indirect
cooking uses heat from adjacent burners to cook food and in many cases, reduces the possibility of
overcooked or overly browned food. Foods most appropriate for indirect grilling included breads, thicker
pieces of chicken or steaks.

TO LIGHT THE GRILL BURNER:

NOTE: Open the grill lid and/or remove the top grate cover before lighting. Turn all knobs to “OFF”.

Tur n the main gas supply on. If you smell gas, shut-off gas supply and call for service.

Push and hold the ignition button, turn the selected burner knob to “HI”.If burner does not light in 4
to 5 seconds, turn knob “OFF” and wait 5 minutes before trying again for any accumulated gas to
dissipate.

Match Lighting:

If the burner will not light after several attempts then the burner can be match lit. If you’ve just
attempted to light the burner with the ignition, allow 5 minutes for any accumulated gas to dissipate.
Keep your face as far away from the grill as possible and hold and pass a lit,long stem match over the
hole located on the top left for burner on the left, or the right hole for the right burner (on page 18,
Fig.18). Push and turn the control knob which is centered on the burner where the lit match is located,
to “HI”. If the burner does not light in 4 seconds turn the knob off,wait 5 minutes and try again.

Once the left or right burner is lit, the adjacent burner(s) can be lit by the cross-lighting method. For
center burners to cross light,light the adjacent far left or right burner using the standard or match light
procedure. Push and turn the control knob for the desired center burner to “HI”.The gas will be ignited
by the adjacent burners flame. If the burner does not light in 4 seconds, turn knob off,wait 5 minutes
and try again.

HEAT

Burner Off

Indirect Heat Grilling

Food
Grill

Rack

Burner

Direct Heat Grilling

(Hot Dogs, Hamburgers,

Typical Thickness Steaks/Chicken)

HEAT HEAT

USING THE GRILL/LIGHTING INSTRUCTIONS

FIG.17

FIG.18

18

USING THE ROTISSERIE

The grill rotisserie system is designed to cook
items from the back using infrared heat. The
location of the burner allows the placement of the
rotis basting pan (included) beneath the food to
collect juices and drippings for basting and gravy.
To flavor the contents of the basting pan, you can
add herbs, onion, garlic, or spices. Hams are
especially good with the addition of pineapple
slices and brown sugar to the basting pan. The
rotisserie burner is an infrared type which
provides intense searing radiant heat. Preferred
by chefs over other methods, this intense heat is
magnificent for searing in the natural juices and nutrients found in quality cuts of meat.

Once lit, the rotis burner will reach cooking temperatures in about 1 minute. The orange/red glow will
even out in about 5 minutes.

The rotis motor is equipped with metal gears and is capable of turning up to a 25 lb. cut of meat or
poultry. The rotis motor on the grills is secured down to a cast rotis block with two black screw- down
knobs. The rotis block is in turn bolted to the right side panel. The rod for the rotis is assembled into
the motor assembly by placing the pointed end into the motor, and resting the handle end on the
support at the left side of the grill. With the rod pushed as far as possible into the motor,the grooved
rod should rest on the rollers.

To load the rod begin with the handle in place, and slide one
of the meat holders (prongs facing away from the handle)
onto the rod. Push the rod through the center of the food,
then slide the second meat holder (prongs toward the food)
onto the rod. Center the product to be cooked on the rod
then push the meat holders firmly together. Tighten the L
shape nut with pliers. It may also be necessary to wrap the
food with butchers string or dental floss (never use nylon or
plastic string) to secure any loose portions. Once the food is
secure, insert the rod into the motor. If needed, remove the
grill grates. Place the basting pan beneath the food. It is
normal for the rod to flex when larger cuts of meat are being
cooked.

Also, the motor is equipped with a halogen bulb to provide
light when other sources of light are not sufficient. Use only
a 50W Max. Halogen Narrow Flood replacement bulb.

CAUTION:

Halogen lamps are constructed of a glass bulb with a pressurized internal
filament tube that operates at high temperatures and could unexpectedly
shatter. Should the outer bulb break, particles of extremely hot glass could be
discharged into the fixture enclosure and/or surrounding environment,
thereby creating a risk of personal injury or fire. When replacing the bulb, let
the bulb cool, and assure that power to the light has been turned off. Never
allow the hot bulb to come into contact with water. DO NOT TOUCH the Light
Bulb when in use. They may be hot enough to cause injury.

FIG. 22

FIG. 23

LIGHT

MOTOR

ROD

19

IMPORTANT:

Never have the grill burners (bottom burners) on during Rotisserie cooking. It
will burn your meat and make it very dry. Use only one thing on at a time, grill
or rotisserie.

PREPARATION
Recommended:

Dental floss or butcher string, scissors, broiler pan (bottom only), pliers, instant read thermometer, foil,
and hot pads.

Working Area:

Allow enough space to accommodate food and
rotisserie rod assembly in a clean environment.

Meat Preparation:

Tie meat with butcher string or Dental floss in
three areas. Buy a roast that is equally balanced
from top to bottom in size. The meat will cook
more evenly while on the Rotisserie. For Poultry,
tie wings and legs to the body using Dental floss
or butcher string to prevent flopping around
while turning. (Fig. 24)

1. Determine the center placement for the food, put 1st prong on Rod, turn L shape screw to
tighten.

2. Center tied meat/poultry on Rod, place second prong, turn L shape screw to tighten. (Fig. 25)

3. Pick up Rod, rotate it to check for balance. If not, adjust prongs and food to balance.Take pliers
and tighten the L shape screw on both sides of the prong.

4. Remove grates and top rack on the grill, place bottom portion of broiler pan on ceramic rods,
so meat drippings can be caught in pan. (Fig. 26)

USING THE ROTISSERIE

FIG. 24

FIG. 25

FIG. 26

20

USING THE ROTISSERIE

COOKING ON ROTISSERIE

1. Place prepared rod into motor,lay across to other side in groove. (Fig.27)

2. Verify placement as shown in Fig.28.

3. Ignite Burner, start Rotisserie Motor,and keep on High for cooking all meats on the Rotisserie.

4. To check temperature, turn off motor, turn temperature to low while using your instant read
thermometer. For poultry it should read 170º in breast. Thermometer should touch the
breastbone, then lift up 3/4 inch from the bone to get a more accurate temperature. Turn on
motor,return heat to high if more cooking is needed. Repeat above instructions. (Fig. 29)

5. Remove Rod,using hot pads, place meat or poultry on broiler pan bottom,then remove prongs.
(Fig.30)

CAUTION:

The fork rods are very sharp. Keep hands away from tips when removing the
food.

6. Cover with foil for a 15 to 20 minute waiting time. Meat will carve better and juices will go back
into the meat.

FIG. 27

FIG. 28

FIG. 29

FIG. 30

21

USING THE ROTISSERIE

TO LIGHT THE ROTISSERIE BURNER:

The location of the rotis burner makes it more susceptible to strong wind conditions,more so than the
protected grill burners. For this reason you should avoid operating the rotis during windy conditions.
As an added safety feature we’ve equipped the burner with an automatic safety valve which will not
allow gas to flow to the rotis burner unless the following conditions are present with the knob on:

1. The safety valve button is pressed, and held down.

2. The safety valve thermocouple has been sufficiently heated to keep safety valve open.

Open the lid. Push and hold the ignition button. You’ll hear a snapping sound. Turn the control knob
to “HI”. Engage the safety valve button and continue to hold until the burner is lit. Once lit, turn control
knob to desired setting. If the burner does not light within 4 to 5 seconds, release the safety valve
button and turn the control knob to “OFF” and wait 5 minutes before trying again.

 If relighting a hot burner, wait 5 minutes.

 Never leave the control knob on if rotis is not in use.

 Never light a grill burner under the rotis while rotisserie burner is lit.

MANUAL LIGHTING:

To manually light the rotisserie, place a
butane lighter near the tip of the thermo­couple as shown in Fig.31. Turn the control
knob to “HI”.Hold the safety valve button in
for about 4 to 5 seconds or until the burner
remains lit. Once lit, turn control knob to
desired setting. If the burner does not light
within 4 or 5 seconds, release the safety
valve button and turn the control knob to
“OFF” and wait 5 minutes before trying
again.

WAR NING:

Keep hands and face away from front of burner! STAND TO THE SIDE WHEN
LIGHTING. ONCE LIT MOVE HAND AWAY QUICKLY.

WAR NING:

Electrical Grounding Instructions: This appliance (rotisserie motor) is equipped
with a three-prong (grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from this plug.

The Rotisserie motor must be electrically grounded in accordance with local codes or, in the absence
of local codes,with the National Electrical Code,ANSI/NFPA 70-1990. Keep the Rotisserie motor electric
cord away from the heated surfaces of the grill. When not in use, remove and store the motor in a dry
location.

Thermocouple

FIG. 31

22

CARE AND CLEANING

BATTERY
REPLACEMENT:

1. Remove drip pan.

2. Open cart door.

3. Pull battery downwards
(This may require use of
pliers.)

4. Re-install upward and
push to snap - Fig. 32.
(Polarity is shown in
Fig. 33).

NOTE: Battery condition should be checked at least once a year.

GRILL GRATES:

The easiest way to clean the grill is immediately after cooking is completed and after turning off the
flame. Wear a barbeque mitt to protect your hand from the heat and steam. Dip a fine brass bristle
barbeque brush in tap water and scrub the hot grill.

DRIP PAN AND GREASE TRAY:

The full width drip pan with grease tray will collect grease from the grill section and boil overs and
spills from the power burners. Allow the pan and its contents to cool before attempting to clean.
Clean grease from the pan often to avoid the possibility of a grease fire.

CERAMIC RODS:

It is not necessary to remove the ceramic rods for cleaning. They burn themselves clean during the
next cooking operation. Periodically the trays holding the ceramic rods need to be turned over, and
shaken free of debris for a thorough cleaning. How often you use the grill and the amount and type
of food cooked will determine when it is necessary to clean the ceramic rods. If grease can be seen on
the top of the tubes or if you get a lot of flare-up during cooking,the tubes need to be turned over and
heated on “HIGH” for 30 minutes; longer for heavy soil.

STAINLESS STEEL:

The Grill is made from non-rusting and non-magnetic stainless steel. After initial usage, areas of the
grill may discolor from the intense heat given off by the burners, this is normal. There are many
different stainless steel cleaners available. Always use the mildest cleaning procedure first, scrubbing
in the direction of the grain. To touch up noticeable scratches in the stainless steel, sand very lightly
with dry 100 grit emery paper in the direction of the grain. Specks of grease can gather on the surfaces
of the stainless steel and bake on to the surface and give the appearance of rust. For removal use an
abrasive pad (Scotch Brite is good) in conjunction with a stainless steel cleaner. Always rub in the
direction of the grain.

Note: Stainless steel tends to rust in presence of chlorides and sulfides specially in coastal areas.

To ensure rust prevention, wash all stainless steel surfaces every 3-4 weeks with fresh water
and stainless cleaner.

FIG. 33

FIG. 32

23

GRILL BURNER:

Remove the grill grates,then lift out the grill radiant tray. Grasp the burner, pull it up and slightly to the
rear of the unit so the burner head comes off the brass orifice at the front, angle the burner sideways,
and remove.

Grill burner cleaning:

Clean the exterior of the burner with a wire brush. Clear
stubborn scale with a metal scraper. Clear any clogged ports
with a straightened paper clip. Never use a wooden toothpick
as it may break off and clog the port. Shake out any debris
through the air shutter. Use a flashlight to inspect the burner
inlet to ensure it is not blocked. If obstructions can be seen,
use a metal wire coat hanger that has been straightened out.

ORIFICE CLEANING:

With the burner removed, remove the orifice and shine a flashlight through the opening to ensure
there is no blockage. Use a needle to clear any debris. Be extremely careful not to enlarge the hole or
break off the needle. See Fig. 35.

WAR NING:

IT IS EXTREMELY IMPORTANT TO
CENTER THE BURNER ON THE
ORIFICE PROPERLY TO PREVENT A
FIRE HAZARD OR EXPLOSTION.

Be careful not to upset the air shutters’ original position (unless readjusting). Lower the rear of the
burner into the cutouts on the support channel at the rear of the burner box. Make sure it is level and
does not rock. Light all of the burners and check for proper flame characteristics. If adjustments are
necessary, refer to (page 14). Do this prior to cooking on the grill.

BURNER REMOVAL AND CLEANING

FIG. 35

5/16" min

Orifice must be securely
fitted inside venturi hole.

Control
Valve

Burner Venturi

24

TROUBLESHOOTING

BEFORE CALLING FOR SERVICE:

If the grill does not function properly, use the following checklist before contacting your dealer for
service. You may save the cost of a service call. Troubleshooting is for general purposes only. If the
problem persists and you feel you require service, contact your dealer or the nearest authorized
agency to perform service. Only authorized agencies can perform warranty service. Call DCS Customer
Service at [phone].

Grill won’t light when the ignition button is pushed:

1. Ensure the grill is cool. Remove the grill top grates and the ceramic radiant trays, watch the
electrode tip. You should see a spark jump from the tip of the electrode when the ignition
button is pushed.

2. If there is no spark when ignition button is pushed, check the battery condition. Battery

condition should be checked at least once a year.

3. Attempt to match light the burner (see page 17-18). Check to see that other burners on the unit
operate. Clean ignition tip of any debris.

Burner flame is yellow or orange,in conjunction with the odor of gas:

1. Check the burner inlet for obstructions such as spider webs. Check the air shutter for proper
adjustment.

2. Grill may be in a dusty area. Move to less dusty area if possible.

Low heat with knob in “HI” position:

1. If only one of the burners appears low, clean the orifice and burner, clearing ports of any
obstruction (see page 25).

2. Grill may be in a dusty area. Move to less dusty area if possible.

3. Check for proper gas supply and pressure.

4. Pre-heat grill for a full 15 minutes.

5. If using LP, gas check for empty tank.

Optional Rotisserie won’t light:

1. Is there is a spark at the electrode?

2. Does the rotis burner light when attempting to match light?

Optional Rotisserie lights, but will not hold flame once button is released:

1. Continue holding safety valve button in depressed position until burner remains lit when
released.

25

ITEM DESCRIPTION PART NO.

1Grate BGB30 19503-01

1a Grate BGB30 19503-02

2Radiant Assembly BGB-30 33248

2a Radiant Cap 33246

2b Radiant 33245

3Ceramic Rods 9.50 32224

4Tube Burner 12285

5Heat Shield,Fire Box 41190

6Manifold Assembly

BGB30-BQRL 33177-01

BGB30-BQRN 33177-02

TEM DESCRIPTION PART NO.

7Washer 15005-15

8Screw 15003-15

9Air Shutter 12003-1

10 Control Valve 13017

11 Ignition Button 18353

12 Wire With Terminals 16438-04

13 Bezel 14006-PL

14 Screw 15001-29

15 Knob BGA 14351

16 NI-Chrome Wire Coil 32313

17 Collector Box 32801

18 Burner Electrode 14.5” 16281-02

Burner Electrode 29” 16281-03

19 Screw 15001-23

20 Wire w/ Terminals 16438-01

21 Nut 15140

22 Screw 15001-17

23 Bracket,Igniter 33223

24 Alkaline 9V Battery 18354

25 Battery Igniter 18350

26 Screw 15002-36

27 Regulator, LP Gas 13230

28 Regulator, Nat.Gas 13035

GRILL BURNER ASSEMBLY

1a

1

2

27

3

19

17

23

16

24

4

18

5

13

6

14

25

28

7

15

9

10

8

11

2a

2b

8

7

20

21

22

26

12

26

GRILL BODY PARTS LIST

ITEM DESCRIPTION PART NO.

9Service Panel, BGB30 33218

10 Firebox,BGB30 33290

12 Bottom/Back Panel,BGB30 33208

14 Landing Ledge,BGB30 33207

15 Rack Roller 14197-02

16 Front Baffle,BGB30 33213

17 Safety Valve Box 33068

19 Drip Pan Assembly, BGB30 33178

21 Screw 15002-17

22 Keps Nut 15021-04

23 Nut 15004-09

24 Drip Pan,BGB30 33215

25 Handle,Drip Pan,BGB30 33214

26 Screw 15001-23

27 Logo 17382-01

28 Valve Panel, BGA30 33212

29 *Insulated Jacket 30,Stainless Steel BGB30-IJS

* For use when building into
combustible enclosures (see
page 11 for built-in details)

7

3

5

23

25

21

29

24

19

2

4

9

10

14

12

1

6

8

15

16

17

22

26

27

28

ITEM DESCRIPTION PART NO.

1Lid Assembly,BGB30 33291

2Lid,BGB30 33220

3Bolt 15003-06

4Stanchion, Lid Handle,R/H 18372-01

5Lid Handle,BGB30 55773-01

6Stanchion, Lid Handle,L/H 18372-02

7Warming Rack,BGB30 19504

8Screw 15001-23

27

ITEM DESCRIPTION PART NO.

16 Bolt 15003-21
17 Bulb 16235
18 Rotisserie,Motor Assembly

Right Side Mounting (Standard Configuration) 33060-01

Left Side Mounting (Special Order) 33060-02
19 Rotis Block 14155
20 Rotis Mounting Arm 14161
21 Screw 15003-09
22 Bracket,Rotis Support R/H 33173-01
23 Bracket,Rotis Support L/H 33173-02
24 Tube Safety Valve/I/R Burner, BGB30 18526-02
25 Safety Valve Knob 14108
26 Safety Valve Bezel 14160
27 Safety Valve 91107
28 Tubing Manifold/Safety Valve 18526-01
29 Control Valve 13017
30 Bezel 14006-PL
31 Knob BGA 14351

ITEM DESCRIPTION PART NO.

1Fork Rotisserie 19010-02
2Rotisserie Rod, BGB30 19511
3Handle, Rotisserie Rod 18040
4Screw 15001-26
5Heat Shield,BGB30 33217
6I/R Burner,BGB30 12021-02
7Wrapper,I/R Burner,BGB30 33216
8Elbow 18030

9Electrode,Rotisserie 16568
10 Electrode Housing L/H 32047-01
11 Thermocouple 13007-2
12 Acorn Nut 15019-06
13 Rack Roller 18211
14 Screw 15001-23

15 Acorn Nut 15019-07

ROTISSERIE ASSEMBLY

24

10

2

3

4

5

19

20

13

18

22

6

11

7

8

9

27

1

23

26

28

25

29

30

31

12 13

15

16

12

21

14

14

17

28

30 GRILL CART PARTS LIST

ITEM DESCRIPTION PART NO.

1Side Shelf Tray 41067

2Side Shelf End Cap 14205

3Side Shelf Assembly 18212

4Bolt 15003-06

5Left Body Panel 33275

6Rear Body Panel 33272

7Right Side Body Panel 33330

8Door Header 33277

9Retainer Tank 33278

10 Frame Cart W/A 33329

11 Hex Bolt 15003-06

12 5”Caster w/o Brake 18022

5” Caster w/Brake 18022-1

13 Nut 15021-09

14 Caster Stiffener 41126

NOTE: Carts sold separately.

ITEM DESCRIPTION PART NO.

15 Siro handle DCS 18204-02

16 Rubber Bump 18403

17 Door Catch 14204

18 Screw 15002-50

19 Door Assembly 33326

20 MS1/4-20 15002-61

21 Hub Cap 41075-02-SP

22 Retaining Ring (E-Style) 15121-01

23 8”Solid Rubber Wheel 18264

24 Axle 33282

25 Bracket Mounting Door Catcher 33327

26 Screw 15002-36

27 Door Catcher Bracket 33017

28 Top Hinge R/H Assembly 41188-01

29 Bottom Hinge R/H Assembly 41184-01

15

2

3

4

5

18

23

27

17

25

17

6

16

7

10

13

14

29

1

24

12

16

8

11

9

19

28

22

21

26

20

29

CART ASSEMBLY INSTRUCTIONS

IMPORTANT:

THE CART MUST BE ASSEMBLED BEFORE ANY GAS CONNECTION CAN BE MADE.

TOOLS REQUIRED (not included):

Phillips Head Screwdriver. 7/16”Wrench or Socket, Protective Gloves To Be Worn

BEFORE ASSEMBLING THE CART:

STEP 1:

Remove packaging

a) Cut shrink wrap and banding material off.

b) Remove top cardboard tray and cardboard corners and then cut bottom tray to allow cart to be rolled out.

c) Recycle packaging.

STEP 2:

Remove side shelves and side trays from inside and discard bubble wrap.

STEP 4:

Attach the side shelf on the right side (left side is optional side burner location)

a) Attach shelf to the right side

of the cart using 1/4 nuts and
bolts provided [leave out (1)
bolt as shown].

b) Do not tighten bolts

(finger tight only) until
completing Step 5-E.

Leave this bolt
out until Step 5

STEP 3:

Part list included

P

art No. Description Quantity

1) 10348 Bag, Hardware, Self adhesive (1)

2) 17726 Assemby instructions BGB Cart (1)

3) 15001-23 Machined Philip screws 10x24x1/2(Use for Step 5 and Step 6) (5)

4) 15003-06 Hexbolt 1/4x20x1/2 (Use for Step 4) (5)

5) 15021-09 Nut Hex 1/4–20 (Use for Step 4) (5)

6) 15147 (1/4–20) 2”bolt (Use for Step 5) (2)

Keps
nuts
and
bolts

30

CART ASSEMBLY INSTRUCTIONS

STEP 5:

Grill placement onto cart

A) Remove drip tray/pan for easier handling.Place grill head on cart

B) Slide back

C) Ease over rear flange

D) Secure with screws

E) Install bolts from Step 4. After head is in place, install bolts omitted from Step #4 and tighten all bolts

on bracket.

NOTE: The bolt secures the side bracket to the grill head assembly for added side shelf strength.

A) After drip tray/pan is removed,

carefully place grill head on cart
(2 person minimum).

C-1) Grill head should rest over

rear cart flange as shown on
right.

C) Lift grill over rear flange of

cart (be aware of pinch
points).

D) Secure grill to rear of cart with

phillips-head screws (provided).

B) Once Grill rests on cart, ease grill

to rear of cart as shown.

Pinch Point

STEP 6:

Final assembly

Install remaining screws in front of head to cart. Slide drip tray/pan back
into place. Move side shelf bars up and set trays into place.

Secure grill to the front of the cart
with Phillips-head screws
(provided).

E) Install bolts omitted from Step

4 to secure grill body to the cart
side for added strength.

31

CART ASSEMBLY INSTRUCTIONS

IMPORTANT

Please see Grill Use/Care Guide for proper gas hookup, testing, and safety
precautions before using the Professional Grill.

CONVENIENCES:

Easy lowering of side shelf

STEP 8:

Gas hookup - LP hookup

Attach LP gas line connector hose assembly (as shown in “LP Gas Hookup”
section - Use/Care Guide) and then connect to LP tank as shown below.

STEP 7:

A) Side tray adjustment

1) Take the tray and place it onto the handle at a upright position.

2) Make sure the tray sits snugly around the handle.

3) Then tighten the rest of the loose bolts that were not tightened in Step 4.

B) Side shelf adjustment

1) With extended use,the shelves
may become unleveled and need
to be readjusted.

2) In between the bracket where
the handle slides in is a 3/8”
adjustment screw. Grasping the handle as shown, raise up the shelf and hold while with other hand using a
3/32 allen wrench turn to the desired level.

Shelf Level
Adjustment

32

WIRING DIAGRAM BGB30-BQR MODELS

Wiring Diagram
P/N # 18529

I/R Burner Electrode
#16568

Burner Electrodes

#16281-02

#16281-03

#16438-01

9 Volt Battery
#18354

Ignition Module

#16438-04

#16438-04

Ignition Switch
#18353

33

SERVICE

HOW TO OBTAIN SERVICE:

For warranty service, contact DCS Customer Service at [phone]. Before you call, please have the
following information ready:

 Model Number

 Serial Number

 Date of installation

 A brief description of the problem

Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your satisfaction,
please write or fax us at:

Write:

DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647

Fax us at: [phone]

34

WARRANTY

Length of Warranty:

One (1) Year Full parts and Labor Covers the entire product
Five (5) Year comprehensive warranty covering the porcelainized cast iron rangetop burners,

grill radiant assemblies, and drip pans. Should structural deterioration occur to the degree of
non-performance, a replacement will be furnished.
Lifetime Warranty on all stainless steel components, including stainless steel grill burners
and stainless steel grill racks (excluding discoloration or surface corrosion).

DCS Will Pay For

All repair labor and parts found to be defective due to materials or workmanship for one full year “IN
HOME” warranty during the first year of ownership. This does not apply if the unit was subjected to
other than normal household use. Service must be provided by Authorized Factory Technician during
normal working hours. No charges will be made for repair or replacement at the location of initial
installation or factory for parts returned pre-paid, through the dealer and claimed within the warranty
period, and found by DCS to be defective.

Replacement will be F.O.B. DCS, and DCS will not be liable for any transportation costs, labor costs, or
export duties. This warranty shall not apply, nor can we assume responsibility for damage that might
result from failure to follow manufactures instructions or local codes, where the appliance has been
tampered with or altered in anyway or which, in our judgement, has been subjected to misuse,
negligence, or accident.

DCS Will Not Pay For

n Installation or start-up.

n Shipping damage.

n Service by an unauthorized technician.

n Damage or repairs due to service by an unauthorized technician or the use of unauthorized

parts.

n Service during other than normal working hours.

n Improper installation, such as improper hook-up, etc.

n Service visits to teach you how to use the appliance; correct the installation; reset circuit

breakers or replace home fuses.

n Repairs due to other than normal household use.

n Damage caused from accident, abuse,alteration, misuse,incorrect installation or installation not

in accordance with local codes.

n Units installed in non-residential application such as day care centers, bed and breakfast

centers, churches, nursing homes, restaurants, hotels,schools, etc.

This warranty applies to appliances used in residential applications; it does not cover their use in
commercial situations. This warranty is for products purchased and retained in the 50 states of the
U.S.A., the District of Columbia and Canada. This warranty applies even if you should move during the
warranty period. Should the appliance be sold by the original purchaser during the warranty period,
the new owner continues to be protected until the expiration date of the original purchaser’s warranty
period.

This warranty is in lieu of all other warranties,express or implied, and all implied warranties, including
warranties of merchantability and fitness for a particular purpose, are hereby disclaimed to the full
extent permitted by law. To the extent that implied warranties may not be disclaimed, the duration of
any implied warranties, including implied warranties of merchantability and fitness for a particular
purpose, are limited to the duration of this express warranty. This warranty gives you specific legal
rights. You may also have other rights which vary from state to state.