Dynalite RR-4G, RR-AR Instruction Manual

Many of the Dynalite lighting accessories shown here are interchangeable with other
Dynalite flash heads and monolights.

RH1050 SH2000 Uni250R

MH2050 Sh4080 Uni400JR

RR-50

50º Reflector—10” diameter l

RR-80 80º Reflector—9” diameter l
RR-AR Angle Reducing Ring 140-60º l
RR-AF Accessory Frame l
RR-AFBD Accessory Frame w/4/ Barn Door l
RR-GH 7” Grid Spot Holder l
RR-4G 7” Grid Set (10,20,30,40º) l l l
SR-65 65º Grid Reflector 7” diameter l
UNI-GR7 65º Grid Reflector 7” diameter l
SR-65FF Barn Door & Filter Frame for SR-65 l l
SR-50 50º Grid Reflector 9” diameter l
UNI-GR9 50º Grid Reflector 9” diameter l
SR-503G 9” Grid Set (3) 20,30,40º for SR-50 l l
SR-503D 9” Barn Door for SR-50 l l
SR-80 80º Softlight Reflector with diffuser l l
SR-80FD Silk Diffuser for SR-80 l l
AR-0040 40º Long Throw Reflector 11” Diameter l
SR-65SN Snoot for SR-65 l l l
SR-OS Optical Spot (only) l
SR-OSTH Magnetic template holder 1
SR-OS20 20 Stainless steel templates w/case1
SR-OS25 25 Stainless steel templates w/case1
LB-2432 ProV 24” x 32” Lightbank l l l
LB-3648 ProV 36” x 48” Lightbank l l l

All Dyna-Lite speed rings, umbrellas, and light stands work with all Dynalite flash

Instruction Manual

Model # RR-GH Grid Holder
Model # RR-4G Grid Spot Set
Model # RR-AR Angle Reducing Ring

1050 Commerce Ave

Union, NJ 07083

800-722-6638 / Fax [phone]

[e-mail]

www.dynalite.com

Grid Holder & Grid Set Instructions

Your new Grid Set will add another dimension of light control to your Dynalite system.
The Grid Set consists of four grids per set: one set 10º, 20º, 30º, 40º, in black. The
grids will provide a basic spot light effect and will have a sharp fall-off light pattern.

The Grid Holder is the interface between the grids and your Dynalite RH-1050 and
MH2050 flash head. The SR-65 on your SH2000 and SH4080 flash heads also dou­bles as a 7” grid holder as well. Gels can also be used in the RR-GH grid holder and
the SR-65 reflector. Additionally, Comet grids, or any other 7” grid can be used in the
Dynalite Grid Holder.

Instructions:

Dynalite Grids are simple to use and require no
special instruction. They snap into the Dynalite
RR-GH grid holder or SR-65 reflector. To use the
Dynalite Grids follow this procedure:

1. Disconnect the flash head from the power
pack.

2. Install the Dynalite Grid Holder (RR-GH) on
flash head. NOTE: Make sure the three (3)
spring clips on the grid holder are on the
accessory ring.

3. Select the grid of your choice and gently
press the grid (RR-4G) into the grid holder.

4. To change or remove the grid, pull the at­tached Teflon tab.

5. To remove the Holder or Angle Reducing
Ring, let unit cool, then push the spring clips
up and over the accessory ring from the
back.

Packing and Storing:

Do not pack this or any accessory that is still hot to the touch. Hot accessories should
be allowed to cool prior to packing or storing

.

Use As Gel Holder:

To use various color gels, you must cut the gel material to fit into the grid adapter or
reflector. Trace the grid adapter on high temp gel material such as Roscolux Gel Mate­rial or equivalent. Cut out the round gel and insert it between the grid and the grid
holder.

Important Safeguards

Please take a moment to read these safety precautions and instructions. Spending
a few moments now will ensure years of use in the future.

1 Read and understand all instructions.
2 Care must be taken as burns could occur from touching the modeling lamp(s)

or flash tube(s).

3 Do not install or remove any accessory until the flash head is disconnected

from power pack.

4 Allow flash heads and accessories to cool completely before storing or removing

accessories or flash head.

5 Do not let cords or cables hang on or touch hot accessories or surfaces.

Please save these instructions so that all users may read this information

Angle Reducing Ring

The angle reducing ring allows you to
reduce the angle of coverage from
140º to 60º for the RH1050, MH2050
series flash heads. The quality of light
will be similar to the flash heads’ built­in reflector and will retain the “hard
edge” look.* To install, simply follow
the instructions for the grid holder on
the next page.