Dynalite DMC2 Installation Instructions Manual

www.lighting.philips.com/dynalite

DMC2-UL, DMC2-CE

441 mm (17.36 in)

523 mm (20.59 in)

540 mm (21.26 in)

380 mm (14.96 in)

106 mm

(4.17 in)

285 mm (11.22 in)

352 mm (13.86 in)

X 4

Modules

1 2

Installation Instructions

Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l’installazione
Installatie-instructies

インストール手 順

安装指示

40° C (104° F)

0° C (32° F)

≤

90%

Modular Controller

DMC2

Devices must be installed by a

qualied electrician in accordance with
all national and local electrical and
construction codes and regulations.

Les appareils doivent être installés par un
électricien diplômé conformément à tous les
codes et réglementations électriques et de
construction nationaux et locaux.

Die Geräte sind von einem qualizierten Elektriker
in Übereinstimmung mit allen geltenden
Vorschriften zu installieren.

Los dispositivos deben ser instalados por un
electricista calicado y cumpliendo todas las
normas y regulaciones, tanto nacionales como
locales, sobre instalaciones eléctricas y obras.

I dispositivi devono essere installati da un
elettricista qualicato in conformità con le norme
locali e nazionali vigenti in materia di costruzioni
edilizie e installazione di impianti elettrici.

De apparaten moeten worden aangebracht
door een gekwaliceerde elektricien en in
overeenstemming met alle nationale en
plaatselijke elektriciteits- en bouwvoorschriften.

装置を取り付ける際は、資格のある電気技師に依頼し、
国および地域の電気および建設に関するすべての法令に
従 ってくだ さい 。

根据国家/地区及当地的电气与建筑规范和法规，该设
备必须由有资质的电工进行安装。

.

IEC Pollution Degree II

2

3 A 3 B

4

N1
N2
N3
L1
L2
L3

N1

L1

N2

L2

N3

L3

N1

L1

N2

L2

N3

L3

Supply
Module

Output
Module 1

Output
Module 2

Communications
Module

+24 V
GND

BUS

BUS

BUS

IEC Overvoltage Category III

3

DCM-DyNet

DCM-DyNet

1 Nm

8.8 Lb-in

5

6

4

MODULE

1

2

Installation example
Exemple d'installation
Installationsbeispiel
Ejemplo de instalación
Esempio di installazione
Installatievoorbeeld

設置例`

安装示例

1 Nm

8.8 Lb-in

8

DSM2-XX

1 Nm

8.8 Lb-in

DSM2

7

5

N1

SUPPLY

N1

L1

N2

L2

N3

L3

MODULE 1

N1

L1

N2

L2

N3

L3

MODULE 2

N2

N3

L1

L2

L3

N

L1

L2

L3

MODULE

Installation example

Exemple d'installation
Installationsbeispiel
Ejemplo de instalación
Esempio di installazione
Installatievoorbeeld

設置例`

安装示例

N1

SUPPLY

N1

L1

N2

L2

N3

L3

MODULE 1MODULE 2

N2

N3

L1

L2

L3

N

L1

L2

L3

MODULE

Installation example

Exemple d'installation
Installationsbeispiel
Ejemplo de instalación
Esempio di installazione
Installatievoorbeeld

設置例`

安装示例

10

9 A 9 B

DyNet RS-485

DSM2

1

2

DCM-DyNet

11

12

DMC2 DMC4

Refer to enclosure label for earth bar wire gauge and

torque ratings

Refer to enclosure label for earth bar wire gauge and

torque ratings

Device must be de-energized before terminating cables.

Do not energize without the front lid top cover in place.

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice – This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help. Any modications not approved by the manufacturer of this device could void the user’s authority to operate this device.

Installation of a home and building automation and control system shall comply with HD 60364-4-41. The temperature limits and current-carrying capacities for
the communication wires specied in HD 384.5.523 shall not be exceeded.

This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB­003 du Canada: CAN ICES-3(B)/NMB-3(B).

13

1

2

4

3

14

Channel 1:

Channel 2:

Channel 3:

Channel 1:

Channel 2:

Channel 3:

Channel 1:

Channel 2:

Channel 3:

AZZ 431 0818 R12

© 2019 Signify Holding. All rights reserved. Specications are subject to
change without notice. No representation or warranty as to the accuracy or
completeness of the information included herein is given and any liability
for any action in reliance thereon is disclaimed. Philips and the Philips
Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other
trademarks are owned by Signify Holding or their respective owners.

www.lighting.philips.com/dynalite