ADSL2+ Wireless Modem Router
Single Ethernet Port with 11g Wireless and Firewall
RTA1030W
FEATURES
>
Broadband Internet Access up to 24 Mbps
>
Supports ADSL, ADSL2 and ADSL2+
>
Simple Configuration
>
Integrated 54 Mbps Wireless Access
>
Wireless Security, WEP and WPA
>
Single
Ethernet Port for Internet Sharing
>
Suitable for Home and Office Networks
>
Security Firewall & DMZ
>
VPN Passthrough
>
Port Forwarding, UPnP™ and QoS
>
Lifetime technical support
NZ 0800 653 962
AUS 1800 063 962
12 month
warranty
www.dynalink.co.nz
www.dynalink.com.au
Get Connected.
Single Ethernet Port with 11g Wireless and Firewall
Technical Specifications (RTA1030W)
ADSL Compliance
ADSL
• ANSI T1.413 Issue 2
• ITU G.992.1 Annex A (G.dmt)
• ITU G.992.2 Annex A (G.lite)
• ITU G.994.1 (G.hs)
• Support dying gasp
• Maximum Rate: 8 Mbps downstream and
1 Mbps upstream
ADSL2
• ITU G.992.3 Annex A (G.dmt)
• ITU G.992.4 Annex A (G.lite)
• Maximum Rate: 12 Mbps downstream and
1 Mbps upstream
ADSL2+
• ITU G.992.5 Annex A (G.dmt)
• Maximum Rate: 24 Mbps downstream and
1.2 Mbps upstream
ATM
• PPPoA (RFC 2364) and PPPoA Bridged mode
• PPPoE (RFC 2516) and PPPoE Bridged mode
• IPoA (RFC 2225)
• Bridged mode over AAL5 (RFC2684/1483)
• ATM Forum UNI 3.1 / 4.0 compliant PVCs
• UBR and CBR with traffic shaping
• OAM F4/F5 loopback cells
Configuration and Management
• Embedded web configuration interface with
password protection
• Remote management control
• Telnet session for local or remote management
• System events logging
• DSL connection diagnostics
• Firmware upgrade via web browser
• User setting backup & restore
• SNMPv1/v2 agent with MIB-II, ADSL Line MIB
Routing
• NAT / PAT allows multiple users to share
Internet access
• UPnP IGD with NAT traversal capability
• Port Forwarding: users can setup multiple virtual
servers (e.g., Web, FTP, Mail servers) on the
local network.
• Static routing & dynamic routing RIPv1/v2
• DNS Relay, Dynamic DNS
• DHCP Client/Relay/Server
• IGMP Proxy
• Support IP/Bridge QoS for different traffic classes
• Support IP/Bridge QoS to prioritise transmission
of different traffic classes
• Support 802.1Q VLAN Tagging
Security
• PAP, CHAP, and MS-CHAP/CHAP2 for
PPP authentication
• Firewall based on incoming & outgoing filtering
of IP address/Port number/Protocol type
• Ping blocking from WAN
• DMZ hosting
Supported Applications
• Application Level Gateways preset for Auth/Ident,
DNS, FTP, PPTP, IPSEC, POP3, SMTP, SSH, TELNET,
TFTP & WEB servers. Multiple Virtual Servers can
be setup in local network.
• VPN passthrough
• NetMeeting, MSN Messenger, FTP, Quick Time,
mIRC, Real Player, CuSeeMe, online gaming.
Bridging
• IEEE 802.1d self-learning bridge
• Learning up to 4096 MAC addresses
• Transparent Bridging between 10/100 Mb
Ethernet and USB
• Supports IGMP Snooping
• Supports 802.1Q VLAN packet pass-through
www.dynalink.co.nz www.dynalink.com.au
Single Ethernet Port with 11g Wireless and Firewall
Technical Specifications (RTA1030W)
Hardware Interface
• One RJ-11 port for ADSL connection
• IEEE 802.11g and 802.11b Wireless LAN interface
• Single Ethernet port for IEEE 802.3/802.3u 10/100
Base-T auto-sensing, auto cross-over
• One USB port compliant to USB v1.1
• One hidden reset button for restoring factory
default settings
Chipset
• Broadcom BCM6348 single-chip ADSL2+ with
integrated MIPS32 CPU, transceiver & Analog
Front End
• Broadcom BCM4318 single-chip 802.11g wireless
LAN solution
Wireless LAN
• Supports IEEE 802.11g and 802.11b
• Data Rates: 54, 48, 36, 24, 18, 12, 9, 6 Mbps for
802.11g and 11, 5.5, 2, 1 Mbps for 802.11b
• Diversity antenna system: one external antenna
and one internal antenna
• Maximum RF output power: 18dBm for 802.11g
• Coverage Area:
802.11g: LOS (Outdoors): Max. 50 meters;
Indoors: Max. 20 meters
802.11b: LOS (Outdoors): Max. 180 meters;
Indoors: Max. 60 meters
• Support WEP (Wired Equivalent Privacy) RC4 with
64-bit or 128-bit key length
• Support Access Control List, only registered WLAN
clients are allowed
• Support 802.1x, WPA-PSK, WPA, WPA2 & Mixed
WAP/WPA2.
Regulatory Approval and Compliance
•ACA
• Telecom New Zealand PTC270
Power Requirement and Operation
Environment Requirement
• Power Adaptor: Output 12 VAC, 1A
• Power Consumption: less than 10 W
• Ambient Temperature: 0 to 40°C
• Relative Humidity: 20% to 90% (non-condensing)
Physical
• Front Panel: 6 LED Indicators
• Back Panel
www.dynalink.co.nz www.dynalink.com.au
Loading...