Dynabrade DynaFine 10800, DynaFine 10810 Important Operating, Maintenance And Safety Instructions

Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes
and regulations. Please refer to Dynabrade's Warning/Safety Operating Instructions for more complete safety information.

Models:
10800 — 15,000 RPM
10810 — Versatility Kit

DynaFine

TM

Parts Page Reorder No.APD97•08

Effective April, 1997

WARNING

!

57961 Cam Assembly

53161 Front Bearing Plate 95884 Hose Clamp Assy. 11016 Bearing 96258 Screw (2)

40544 Bearing 01560 Exhaust Cover50777 Rotor50767 Pin

95558 Retaining Ring

01476 Cylinder

*01448 Throttle Lever

01480 Blades (4) (4 pkg.)

01472 Tip Valve 96065 O-Ring

01464 Seal

12132 Pin

Left Hand Threads

01469 Regulator

(incl. O-rings)

01024 O-Ring

95730 O-Ring

01449 Valve Stem

01488 Housing

Please indicate:
Model #, Serial #,
and RPM
when ordering
replacement parts.

01548 Gasket

95523 O-Ring

01558 Collar

01461 Lock Nut

See inside for Important Operating, Maintenance and Safety Instructions.

01468 Spring

95711 Retaining Ring

57970 Air Control Ring

94522 Muffler Cap

94525 Felt Muffler

94524 Sintered Muffler

94521 Muffler Base

95438 O-Ring

94523 Inlet Adapter

94526 Spacer

95735 O-Ring

01546 Housing

01470 Insert

*Optional 01462 Safety-Lock Lever available.

Loctite/Hernon: L2= Loctite #271,
L

3

= Loctite #609, L4= Hernon #940

Torque: N•m x 8.85 = In. - lbs.

T

2

= 10 N•m, T3= 23 N•m, T4= 28 N•m,

T5= 45 N•m

KEY

L

T

O

T

5

O

T

3

L

4

O

Air Powered Detail Sander.

Shaded parts represent 94520 Muffler Assembly.

T

4

T

2

Right Hand Threads

57976 Boot Assembly 57953 Hook-Face Pad

L

3

Oil

G

Grease

G

L

2

L

4

L

4

AUTOMOTIVE

02673 Rear Bearing Plate

02696 Bearing02679 Shield

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.

Operating Instructions:

Warning: Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety

procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.

2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging

valve body housing.

3. Connect power source to tool. Be careful not to depress throttle lever in the process.

4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be

serviced to correct the cause before use.

Maintenance Instructions:

1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct

the cause before use.

2. Some silencers on air tools may clog with use. Clean and replace as required.

3. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool
specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.

4. An air line filter-regulator-lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11289 Air Line Filter-

Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic
components. Operates 40 CFM @ 100 PSI has 3/8" NPT female ports.

5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.

6. A motor tune-up kit (P/N 96236) is available which includes assorted parts to help maintain motor in peek operating condition.

7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,

chlorinated hydrocarbons or nitro carbons.

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from
Dynabrade, Inc.

•

Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).

•

Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.

•

Always disconnect power supply before changing abrasive/accessory or making machine adjustments.

•

Inspect abrasives/accessories for damage or defects prior to installation on tools.

•

Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

Notice

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can
most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings
causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon
proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of
this tool.

2

(APD97•08)

One Y ear W arranty

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to
have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety
practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal
performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.

Machine Length Weight Spindle Air Flow Rate Sound Motor Motor Air Pressure

Number Inch (mm) Pound (kg) Thread SCFM (LPM) Level HP (W) RPM PSI (Bars)

10800 9.0" (228.6) 1.60 lbs. (.72) None 19.0 (538) 65 dBA .03 (22.4) 15,000 90 (6.21)

Additional specifications: Air Inlet Thread 1/4" (6 mm) NPT • Hose Size 1/2" (13 mm)