Dynabrade 61300, 61301, 61302, 61303, 61304 Operating Manual

Reorder No. PD05.20

Supersedes PD04.21

IMPORTANT SAFETY INSTRUCTIONS

1. Components used in packaging (ie. plastic bags) can be

dangerous keep away from children and animals.

2. The unit is for DRY USE ONLY and must be stored in a dry room.

3. The use of this machine for anything not specified in this

manual may be dangerous and must be avoided.

4. The suction nozzle should be kept away from the body,
especially delicate areas such as the eyes, ears and mouth.

5. The equipment should be correctly assembled before use.

6. Ensure that power socket is correct for the machine.

7. Check the voltage indicated on the rating plate is the same as

the supply voltage.

8. These machines are not designed for picking up health
endangering dusts or inflammable/explosive substances.

9. Never leave the equipment unattended while in use.

10. Never use this equipment to pick up any kind of liquid.

11. Never carry out any maintenance on the machine without first

disconnecting from the main supply, if the machine is to be left
unattended the supply should also be terminated.

12. The main supply cable should not be used to pull or lift the
machine.

13. The machine should never be emersed in water or a pressure
jet of water used for cleaning.

14. Periodically examine the main cable and machine for damage.
If any damage is found contact your service centre for repair.

15. Should extension cables be used, ensure that the cable rating
is suitable for use with the equipment. Do not use the cable
coiled as this could result in a voltage drop or overheating.
Keep dry at all times.

16. This equipment should NOT be used to pick up water from
containers, lavatories, tubs, etc.

17. Service and repairs must be carried out by qualified personnel
only. Replacement parts for the machine must be
manufacturers original spare parts only.

18. The manufacturer cannot be held responsible for any
damage/injury caused to persons or property, because of the
incorrect use of the machine due to procedures being used
which are not specified in this instruction manual.

These Portable Vacuum Systems have been developed as a
safe, portable, mobile, yet powerful industrial tool for
commercial use. To ensure that this quality equipment is
properly used and maintained to its full capability, please
carefully read the following safety instructions and operating
procedures before commencement of the operation.

When operating this equipment, basic precautions should always be strictly followed

including the instructions listed below:

“M” CLASS DRY VACUUM

When employed in accordance with their intended use, the industrial vacuum
cleaners described in these operating instructions are suitable for picking up

non-flammable, dry dusts. They correspond to dust class “M” in accordance to:

EN 60335-2-69. By SLG, Germany

61300 (9.9 gal./36 ltr.) 120v-60Hz (US)
61301 (17 gal./64 ltr.) 120v-60Hz (US)
61302 (9.9 gal./36 ltr.) 230v-50Hz (UK)
61303 (17 gal./64 ltr.) 230v-50Hz (UK)
61304 (9.9 gal./36 ltr.) 110v-60Hz (UK)

61305 (17 gal./64 ltr.) 110v-60Hz (UK)
61306 (9.9 gal./36 ltr.) 230v-50Hz (EUR)
61307 (17 gal./64 ltr.) 230v-50Hz (EUR)
61308 (9.9 gal./36 ltr.) 230v-50Hz (OUS)
61309 (17 gal./64 ltr.) 230v-50Hz (OUS)

Portable Vacuum System

Operating Manual

ASSEMBLY INSTRUCTIONS

1. While opening the carton, carefully inspect outside of the

carton for any sign of transportation damage, and if so, notify
your shipper immediately.

2. Open carton and remove hoses, hose connectors and other
accessories.

3. Lay carton on its back and wheel the unit out.

4. Remove all packing, release the unit and remove

Motorhead/Vacuum Head Assembly to make sure no packing
materials are left inside the unit.

5. Check to make sure the filter is seated firmly. If not, tighten at
base of filter unit.

7. Remove the vacuum hose assembly. Note that the air supply
tube (the smaller of the two) protrudes at both ends and is
longer than the vacuum hose.

8. Connect quick coupler male end to air outlets located on
vacuum head assembly.

9. Insert vacuum hoses.

10. Connect air supply to air inlet fitting (1/4" NPT female threads)

located at the back side of Motorhead. Air pressure should be
adjusted according to the pressure requirement of the air tools

you are using. Do not exceed 150 PSIG (10.3 kg/cm2). Some
pressure drop is unavoidable between the main air supply and
the air tools due to internal flow resistance in a long air hose.

Air pressure of 20 to 30 PSIG (1.4 to 2.0 kg/cm2) higher
than the air pressure specified for the air tool being used
is recommended.

The installation of a Dynabrade Filter-Regulator-Lubricator
(FRL Part No. 11411) is highly recommended to protect the
unit and the air tools.

Where it is critical to avoid shocks or sparks caused by
static electricity, an air supply hose which is electrically
conductive and ground must be used.

11. All Dynabrade Vacuum Models come with a sample dust bag.

Install bag inside main body. Make sure that vacuum
connection tube protrudes through the hole in the bag.

12. Order dust bags (Part No. 64682) before you run out of them.

13. Return Motorhead/Vacuum Head Assembly to the unit and lock

the two rim clamps to secure Motorhead/Vacuum Head
Assembly in position.

14. Connect your Dynabrade air tool or accessory and you are now
ready for working with the Dynabrade Portable Vacuum System.

CAUTION

THIS IS A PRECISION PIECE OF EQUIPMENT designed for dust extraction to keep your ENVIRONMENT
and your REPUTATION “DUST-FREE.” Read operating instructions before using Dynabrade Portable
Vacuum System and be thoroughly conversant with safety precautions in your locality.

Refer to the drawing and parts list for the name and location of parts.

OPERATING INSTRUCTIONS

1. Always wear safety glasses and any other safety items

required by law.

2. The vacuum system will operate by an on/auto/manual switch
located on the front of the Motorhead/Vacuum Head Assembly.
This switch must be turned on to activate the Motorhead.

3. VACUUM SPEED CONTROL: Unit is equipped with a rheostat
motor control. Infinitely adjustable speed allows suction
regulation for wide range of tools.

4. ELECTRONIC THERMAL PROTECTION DEVICE: Unit is
equipped with a overload prevention system. If this feature is
activated a 20 MIN. COOL DOWN PERIOD inhibits use. After a
complete 20 min. cool down period has passed the Electronic
Thermal Protection Device will RE-SET automatically and
the unit will be on line ready for use.

5. VISUAL WARNING SIGNAL: Unit is equipped with a visual
warning (yellow) light to indicate when air velocity falls below
20m/s. Turn off vacuum and replace disposable collection bag.
The warning signal will RE-SET automatically and the unit will
be ready for use.

The following items should be well-noted for the effective use of the unit.

GROUNDING INSTRUCTIONS

This unit must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to
reduce the risk of electric shock.

Where it is critical to avoid shocks or sparks caused by static
electricity, an electrically conductive and grounded air supply
hose must be used.

PAGE 2

WARNING

Grounding by means of a ground wire between both ends of the air supply tubing
passing through vacuum hose is recommended.

NEW!

NEW!