Page 1
Safety, Operation and Maintenance – Save This Document and Educate All Personnel
Parts Page Reorder No. PD12•22
Effective June, 2012
WARNING
Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel as well
as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Standards Institute (ANSI).
Safety Requirements for the Use, Care and Protection of Abrasive Wheels – ANSI B7.1, Compressed Air and Gas Institute (CAGI) Safety Code
for Portable Air Tools – B186.1, Code of Federal Regulation – CFR 29 Part 1910, International Organization for Standardization (ISO) Hand
Held Non-Electric Power Tools – ISO 11148, Safety Requirements and applicable State and Local Regulations.
Find The Most Current Offering of Support Documents and Accessories at www.Dynabrade.com
Read and understand tool manual before work starts
to reduce risk of injury to operator, visitors, and tool.
Ear protection to be worn when exposure to sound,
exceeds the limits of applicable Federal, State or
local statues, ordinances and/or regulations.
Practice safety requirements. Work alert, have proper
attire, and do not operate tools under the influence
of alcohol or drugs.
Air line hazard, pressurized supply lines and flexible
hoses can cause serious injury. Do not use damaged,
frayed or deteriorated air hoses and fittings.
Eye protection must be worn at all times, eye
protection to conform to ANSI Z87.1.
Respiratory protection to be used when exposed to
contaminants that exceed the applicable threshold
limit values required by law.
Some dust created by sanding, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SAFETY and OPERATING INSTRUCTIONS
DO NOT USE Tool for Anything Other Than Its Intended Applications.
Training: Proper care, maintenance, and storage of your air tool will maximize tools performance and reduce chance for accident.
Employer's Responsibility: Provide operators with safety instructions and training for safe use of tools and accessories.
Report to Your Supervisor any Condition of the Tool, Accessories or Operation you Consider Unsafe.
Tool Intent: 2" & 3" Diameter Disc Sanders are ideal for material removal and finishing using 2" & 3" Backup
pads with appropriate sized abrasives.
Carefully Read and Understand the General
and Sander/Polisher sections found in Tool
Safety and Operating Guidelines (PN00001676)
Before Handling or Using Tool.
Carefully Read all instructions before operating or servicing
any Dynabrade®Abrasive Power Tool. Products offered by
Dynabrade are not to be modified, converted or otherwise
altered from the original design.
Model Pad Type
Spindle
Thread
Muffler RPM
48520
2" Locking-Type (Female) 1/4"-20 Extended 12,000
48521
2" Locking-Type (Female) 1/4"-20 Extended 15,000
48522
2" Locking-Type (Female) 1/4"-20 Extended 20,000
48530
3" Locking-Type (Female) 1/4"-20 Extended 12,000
48531
3" Locking-Type (Female) 1/4"-20 Extended 15,000
48532
3" Locking-Type (Female) 1/4"-20 Extended 20,000
48540
2" Locking-Type (Female) 1/4"-20 Standard 12,000
48541
2" Locking-Type (Female) 1/4"-20 Standard 15,000
48542
2" Locking-Type (Female) 1/4"-20 Standard 20,000
2" & 3" Disc Sanders
Right Angle, Rear Exhaust
SANDER / POLISHER
Model 48520
Page 2
MAINTENANCE INSTRUCTIONS
Important: To keep tool safe, a Preventative Maintenance Program is
recommended. The program should included inspection of the tool and all
related accessories and consumables, including air lines, pressure regulators,
filters, oilers, etc. refer to CAGI B186.1 for additional maintenance information.
If accessory or tool breakage occurs, investigate failure to determine the cause
and correct before issuing tool for work. Use the following schedule as a
starting point in developing a Preventative Maintenance Program. If tool does
not operate properly (RPM, Vibration, Start/Stop) after these scheduled
checks or at any time, the tool must be repaired and corrected before returning
tool to use.
INSTALLATION
• To ensure long life and dependable service, use a Closed Loop Air System
and Filter-Regulator-Lubricator as diagramed below.
• Each tool should have its own dedicated hose connected to an air supply
manifold. Quick disconnects should be installed at the manifold in an effort
to reduce contamination into the tool.
• It is strongly recommended that all Dynabrade rotary vane air tools be used
with a Filter-Regulator-Lubricator to minimize the possibility of misuse due
to unclean air, wet air or insufficient lubrication. Dynabrade recommends the
following: 10681 Air Line Filter-Regulator-Lubricator — Provides accurate
air pressure regulation, two-stage filtration of water contaminants and
micro-mist lubrication of pneumatic components.
• Dynabrade recommends one drop of air lube per minute for each 20 SCFM
(example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute) Dynabrade Air Lube (P/N 95842:
1pt/473ml) is recommended.
MAINTENANCE SCHEDULE
Daily (every 8 hours):
• Inspect tool and accessories for damage or broken parts. Replace items
as necessary to ensure proper operation and safety.
• Lubricate motor as recommended. Use Dynabrade Air Lube (P/N 95842:
1pt/473ml) 10W/NR. (1 Drop per minute of air lube per 20 SCFM.)
• Check air line pressure with a gage. (MAX. 90 PSIG or 6.2 Bar operating
pressure at the air inlet of the tool.)
• Right angled gear and wick system through gear case grease fitting with
3 plunges of gear oil (P/N 95848) and grease gun (P/N 95541). (Prime
grease gun prior to greasing.)
• Check tool for proper operation: If operating improperly or demonstrates
unusual vibration, the tool must be serviced and problem corrected before
further use.
Every 20 Hours or Once a Week Which Ever Comes First:
• Check free speed of tool without the abrasive accessory mounted. Measure
RPM (speed) with tachometer and with air pressure set at 90 PSIG while the
tool is running. If a governed tool is operating at a higher speed than the
RPM marked on the tool housing, the tool must be serviced and corrected
before use. A non-governed tool may exceed the RPM marked on the tool
by 10% when operated at free speed with no accessories.
• If tool is running fast look for worn, damaged or missing governors, air
control rings and silencers. Special care must be taken when servicing
governors and speed control devices. Injection molded governor assemblies
are non-serviceable and must be replaced.
• If tool is running slow look for clogged inlet screen, air stream, silencer(s)
or a malfunctioning governor (see concerns for servicing governors).
Service as required.
Every 50 Hours:
• Lubricate planetary gears through gear case grease fitting with 3 plunges
of grease (P/N 95542) and grease gun (P/N 95541). (Prime grease gun
prior to greasing.)
REPAIR
• Use only genuine Dynabrade replacement parts to ensure quality. To order
replacement parts, specify Model#, Serial# and RPM of your air tool.
• Mineral spirits are recommended when cleaning the tool and parts. Do
not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point
(example: WD-40
®
).
• Motor Tune-Up Kit are available (when applicable) which includes high wear
and medium wear motor parts.
• Air tool markings must be kept legible at all times, if not, reorder housing
and replace. User is responsible for maintaining specification information.
• After maintenance is performed on tool, add a few drops of Dynabrade
Air Lube (P/N 95842) to the tool inlet and start the tool a few times
to lubricate air motor. Verify RPM (per 20 hr maintenance schedule),
vibration and operation.
HANDLING & STORAGE
• Use of tool rests, hangers and/or balancers is recommended.
• Protect tool inlet from debris (see Notice).
• DO NOT carry tool by air hose or near the tool throttle lever.
• Store accessories in protective racks or compartments to prevent damage.
• Follow the handling instructions outlined in the operating instructions when
carrying the tool and when changing accessories.
• Protect accessories from exposure to water, solvents, high humidity,
freezing temperature and extreme temperature changes.
END OF USE/ DISPOSAL
When tool has reached its end of useful service, disassemble tool into its
primary components (i.e. steel, aluminum and plastic part) and recycle or discard
per local, state and/or federal regulations as to not harm the environment.
NOTICE
All Dynabrade motors use the highest quality parts and metals available and
are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication.
Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor
blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment
which has been subjected to misuse such as unclean air, wet air or a lack
of lubrication during the use of this tool.
2
Filter
Regulator
Lubricator
90 PSIG
(6.2 Bar)
To Tool Station
Ball
Valve
Ball
Valve
Filter
Regulator
Lubricator
Air Flow
Drain
Valve
Drain
Valve
Air Tool
Air Compressor
and Receiver
Drain Valve
Air Hose
90 PSIG MAX
(6.2 Bar)
Air Flow
Refrigerated
Air Dryer
1 DROP/MIN.
20 SCFM
LUBRICATOR SETTING
• Dynabrade Air Power Tools are designed to operate at 90 PSIG
(6.2 Bar) maximum air pressure at the tool inlet, when the tool is
running. Use recommended regulator to control air pressure.
• Ideally the air supply should be free from moisture. To facilitate
removing moisture from air supply, the installation of a refrigerated
air dryer after the compressor and the use of drain valves at each
tool station is recommended.
➤
➤
➤
➤
➤
➤
AIR SYSTEM
Closed Loop Pipe System, Sloped in Direction of Air Flow
Page 3
48520
– 12,000 RPM
48521
– 15,000 RPM
48522
– 20,000 RPM
48530
– 12,000 RPM
48531
– 15,000 RPM
48532
– 20,000 RPM
48540
– 12,000 RPM
48541
– 15,000 RPM
48542
– 20,000 RPM
2" & 3" Disc Sander
Complete Assembly
Adhesive: A4= Loctite #680
A8= Loctite #567
A10= Loctite #243
Torque: N•m x 8.85 = In. - lbs.
Oil: O
1
= Air Lube
O
A
T
W
KEY
ITEM P/N DESCRIPTION QTY.
1
51344
51346
2" LOCKING-TYPE PAD
3" LOCKING-TYPE PAD
1
2 02029 SPINDLE - 1/4"-20 1
3 02035 LOCK NUT 1
4 01486 FELT SILENCER 1
5 54520 BEARING 1
6 54557 SHIM PACK (3/PKG) AR
7
02623
02597
02599
GEAR – 12,000 RPM
GEAR – 15,000 RPM
GEAR – 20,000 RPM
1
8
02042 BOTTOM WICK
1
9
02043 TOP WICK
1
10 02031 HOUSING ASSEMBLY 1
10.1 02033 BEARING 1
10.2 02041 GREASE PLATE 1
10.3 01041 LUBRICANT FITTING 1
10.4
———
HOUSING 1
11 01547 INSULATOR COLLAR 1
12
45294
45295
45296
SHORT BLOCK ASSY – 12,000 RPM
SHORT BLOCK ASSY – 15,000 RPM
SHORT BLOCK ASSY – 20,000 RPM
1
12.1
02624
02598
02600
PINION – 12,000 RPM
PINION – 15,000 RPM
PINION – 20,000 RPM
1
12.2 02649 BEARING 1
12.3 01479 SPACER 1
12.4 54529 SHIM PACK (3/PKG) AR
12.5 01478 FRONT BEARING PLATE 1
12.6 50767 PIN 2
12.7 45293 ROTOR 1
12.8 01480 VANE (4/PKG) 1
12.9 01476 CYLINDER 1
12.10 02676 REAR BEARING PLATE 1
12.11 02696 BEARING 1
13 45272 GOVERNOR ASSEMBLY 1
14 45320 GOVERNOR CHAMBER 1
15 45307 HOUSING ASSEMBLY 1
16 96077 O-RING 1
17
———
SLEEVE - See Chart Page 4 1
18 97060 PIN 1
19 45315 BUSHING 1
20 97045 PIN 1
21 45263 THROTTLE LEVER 1
22 45310 SEAL 1
23 58365 TIP VALVE 1
24 01468 SPRING 1
25 01564 AIR CONTROL RING 1
26 94535 STANDARD MUFFLER ASSEMBLY 1
26.1 95711 SNAP RING 1
26.2 01486 FELT SILENCER 4
26.3 96065 O-RING 1
26.4 01446 AIR DEFLECTOR 1
26.5 95620 RETAINING RING 1
26.6 01578 INLET ADAPTER ASSEMBLY 1
27 94520 EXTENDED MUFFLER ASSEMBLY 1
27.1 95438 O-RING 1
27.2 94521 MUFFLER BASE 1
27.3 94524 SINTERED BRONZE 1
27.4 94525 FELT SILENCER 1
27.5 94522 MUFFLER CAP 1
27.6 95375 O-RING 1
27.7 94526 SPACER 1
27.8 94523 INLET ADAPTER ASSEMBLY 1
P/N DESCRIPTION QTY.
95262 WRENCH – 14 MM 1
95541 GUN 1
95848 GEAR OIL 1
2
4
5
6
7
8
1
23 N•m
T
A
8
A
4
W
1
W
1
3
10.1
10.2
10.3
10.4
LH
9
A
10
17 N•m
T
11
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
12.10
12.11
LH
LH
0.8 N•m
T
A
10
13
14
15
16
17
18
20
21
34 N•m
T
Always follow adhesive manufacturers
cleaning and priming recommendations.
Models: 48540, 48541, 48542
Models:
48520, 48521,
48522, 48530,
48531, 48532
26.1
26.1
26.3
27.2
26.4
26.5
27.3
26.2
27.1
A
8
T
28
A
8
O
1
T
28
O
1
26.6
27.4
27.6
27.7
27.5
2 N•m
T
A
8
19
22
23
24
25
2" Dia. Models
Standard Exhaust
3" Dia. Models
3
Extended Exhaust Extended Exhaust
27.8
AR – “As Required”
Wicking: W1= Wicking Gear Oil
Page 4
DYNABRADE, INC. www.dynabrade.com
8989 Sheridan Drive •Clarence, NY 14031-1419 •Phone: (716) 631-0100 •Fax: 716-631-2073 •International Fax: 716-631-2524
© DYNABRADE, INC., 2012 PRINTED IN USA PD12.22_12/12R1
American National Standards Institute (ANSI)
1899 L Street, NW, 11th Floor • Washington, DC 20036 • Tel: 1 (202) 293-8020
Compressed Air & Gas Institute (CAGI)
1300 Sumner Ave. • Cleveland, OH 44115-2851
Tel: 1 (216) 241-7333 • Fax. (216) 241-0105
European Committee for Standardization (EN)
Rue de Stassart 36 • B - 1050 Brussels, Belgium
International Organization of Standards (ISO)
Case postale 56 • CH-1211 Geneva 20
Tel: + 41 22 749 01 11 • Fax: + 41 22 749 09 47
Government Printing Office (GPO)
Superintendent of Documents • Attn: New Orders
P.O. Box 371954 • Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
MACHINE SPECIFICATIONS
REFERENCE CONTACT INFORMATION
LIFETIME WARRANTY
To validate Dynabrade Lifetime Warranty, you must register each tool at: www.dynabrade.com. Registration of each tool at website is required.
Dynabrade will not honor Lifetime Warranty on unregistered tools. Please view the entire Lifetime Warranty Policy at : www.dynabrade.com.
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. 1/4" (6 mm)
Sound Level is the pressure measurement according to the method outlined in ISO regulation ISO-15744
2" Diameter - Standard Exhaust
Model Speed Power Sound Air Consumption Air Pressure Weight Length Height
48520 12,000 RPM .4 hp (298 W) 76 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.3 lb. (0.6 kg) 8" (203 mm) 3.5" (89 mm)
48521 15,000 RPM .4 hp (298 W) 79 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.3 lb. (0.6 kg) 8" (203 mm) 3.5" (89 mm)
48522 20,000 RPM .4 hp (298 W) 78 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.3 lb. (0.6 kg) 8" (203 mm) 3.5" (89 mm)
48530 12,000 RPM .4 hp (298 W) 78 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.4 lb. (0.63 kg) 8" (203 mm) 3.5" (89 mm)
48531 15,000 RPM .4 hp (298 W) 79 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.4 lb. (0.63 kg) 8" (203 mm) 3.5" (89 mm)
48532 20,000 RPM .4 hp (298 W) 78 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.4 lb. (0.63 kg) 8" (203 mm) 3.5" (89 mm)
48540 12,000 RPM .4 hp (298 W) 81 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.1 lb. (0.5 kg) 6.5" (164 mm) 3.5" (89 mm)
48541 15,000 RPM .4 hp (298 W) 83 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.1 lb. (0.5 kg) 6.5" (164 mm) 3.5" (89 mm)
48542 20,000 RPM .4 hp (298 W) 81 db(A) 25 SCFM (708 LPM) 90 PSIG (6.2 Bars) 1.1 lb. (0.5 kg) 6.5" (164 mm) 3.5" (89 mm)
OPTIONAL ACCESSORIES
SLEEVE IDENTIFICATION CHART (ITEM #17)
Motor Tune-Up Kit
•
Includes assorted parts to help
maintain and repair motor.
Part No. 96541
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
Part No. 95842: 1pt. (473 ml)
Part No. 95843: 1 gal. (3.8 L)
Gear Oil
•
For geared tools utilizing a wick-type
lubrication system.
•
Apply every 8 hours of operation.
Part No. 95848: 2.5 oz. (74 ml) Tube.
Hex Key Wrench
•
12 mm hex
•
Use in housing core
or air inlet.
Part No. 96399
Crowfoot Wrench
•
3/8" Drive
•
34 mm
•
Use on throttle body, housing
core and lock nuts.
Part No. 96460
Lock Ring Tool
Part No. 50971
•
For removal/tightening
of 02035 Lock Nut.
P/N DESCRIPTION QTY.
45235 SLEEVE - MDL 48540 1
45234 SLEEVE - MDL 48541 1
45233 SLEEVE - MDL 48542 1
P/N DESCRIPTION QTY.
45241 SLEEVE - MDL 48520 1
45240 SLEEVE - MDL 48521 1
45239 SLEEVE - MDL 48522 1
P/N DESCRIPTION QTY.
45238 SLEEVE - MDL 48530 1
45237 SLEEVE - MDL 48531 1
45236 SLEEVE - MDL 48532 1
2" Diameter - Extended Exhaust 3" Diameter - Extended Exhaust
Overhose Assembly
•
Redirects exhaust
away from operator.
Part No. 94994
•
For use with standard
exhaust models only.
Part No. 94995
•
For use with extended
exhaust models only.
Loading...