Dynabrade 10600, 10601, 10602, 10603, 10604 Important Operating, Maintenance And Safety Instructions
2.82 N•m
T
A
3
A
3
A
2
O
1
Models:
10600 – Non-Vacuum
10601 – Vac-Ready
10602 – Basic Vac
10603 – Deluxe Vac
10604 – Central Vac-Ready
Air Powered, Random Orbital Sander, 10,000 RPM
Parts Page Reorder No. APD00•10
Effective November, 2000
Supercedes APD96•05
8" Dynorbital
®
Random Orbital Sander
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools
(ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade’s
Warning/Safety Operating Instructions for more complete safety information.
WARNING
!
Index Key
No. Part# Description
1 11579 Spacer (4) (Ctl.-Vac Only)
2 96427 Washer (4) (Ctl.-Vac Only)
3 96424 Screw (4) (Ctl.-Vac Only)
4 57735 Shroud (Ctl.-Vac Only)
5 57371 Shroud
6 97010 Screw (9)
7 95886 Washer (13)
8 56235 Pad (Vac)
56234 Pad ( Non-Vac)
9 95898 Screw
10 95887 Set Screw
11 54628 Counter Balance
12 01678 Screw (3)
13 54627 Mounting Plate
14 56133 Bearing
15 54685 Bearing Retainer
16 01788 Screw (6)
17 01211 Lock Washer (10)
18 57368 Wiper
19 57397 Wiper Retainer
20 56046 Lock Ring
21 54672 Shaft
22 54673 Key
23 02695 Bearing
24 54630 Front Bearing Plate
25 54705 Rotor/Blade Set (5/pkg.)
26 54631 Cylinder (Incl. 95865 Pin)
27 54629 Rear Bearing Plate
28 01206 Bearing
29 95626 Retaining Ring
30 57382 Gasket (Non-Vac)
57383 Gasket (Vac)
31 10614 Housing – 10600
10615 Housing – 10601
10615 Housing – 10602
10615 Housing – 10603
10616 Housing – 10604
32 95523 O-Ring (2)
33 56671 Handle
34 96123 Screw (2)
35 57396 Valve Stem
36 01464 Seal (2)
37 01472 Tip Valve
38 01468 Conical Spring
39 56673 Gasket
40 96328 O-Ring
41 98597 Retaining Ring
42 56672 Adapter Assembly
43 01024 O-Ring (2)
44 57343 Speed Regulator
45 54199 Muffler Seat
(Non-V, Ctl.-V)
46 54195 Muffler (Non-V, Ctl.-V)
47 54194 Muffler Cap
(Non-V, Ctl.-V)
48 57344 Throttle Lever
49 01017 Pin
50 96421 Flat Washer (2)
51 01494 Inlet Bushing
2
7
8
11
13
15
7
18
22
21
23
24
25
26
27
29
30
31
32
33
34 35 7 17 36 38
37
28
19
17
3
4
5
A
O
T
Oil: O
1
= Air Lube
Adhesive: A
1
= Loctite #609
A2= Loctite #271
A3= Loctite #242
Torque: N•m x 8.85 = In. - lbs.
Key
A
2
A
3
A
2
A
3
A
1
A
2
O
1
For Serial No. 9D1000 and Higher
1
48
49
39 40
41 42 43 44
45
46
47
51
36
17
16
50
10
9
12
16
20
3.38 N•m
T
2.82 N•m
T
9 N•m
T
2.82 N•m
T
23 N•m
T
34 N•m
T
6
1.7 N•m
T
14
6
AUTOMOTIVE
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade®Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade Rotar y Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/ accessory on tool.
2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid
damaging valve body housing.
3. Connect power source to tool. Be careful not to depress throttle lever in the process.
Maintenance Instructions:
1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to
correct the cause before use.
2. Some silencers on air tools may clog with use. Clean and replace as required.
3. All Dynabrade Rotary Vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if
the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1pt. 473ml.)
is recommended.
4. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic
components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.
5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.
6. AMotor Tune-Up Kit (P/N 96122) is available which includes assorted parts to help maintain motor in peek operating condition. Please refer to
Dynabrade's Preventative Maintenance Schedule for a guide to expectant life of component parts.
7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,
chlorinated hydrocarbons or nitro carbons.
2
(APD00•10)
Full One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to
have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety
practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Model Length Height Weight Air Flow Rate Sound Motor Motor Air Pressure
Number Inch (mm) Inch (mm) Pound ( kg) SCFM (LPM) Level Hp (W RPM PSIG (bars)
10600 12" (305) 4-1/2" (114) 3.4 lbs. (15.1) 21 (595) 80 dBA .31 (231) 10,000 90 (6.2)
10601-10603 12" (305) 4-1/2" (114) 3.4 lbs. (15.1) 21 (595) 89 dBA .31 (231) 10,000 90 (6.2)
10604 12" (305) 4-1/2" (114) 3.4 lbs. (15.1) 21 (595) 83 dBA .31 (231) 10,000 90 (6.2)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 3/8" (10 mm)
• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
• Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
• Inspect abrasives/accessories for damage or defects prior to installation on tools.
• Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can
most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings
causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon
proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of
this tool.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Loading...